aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-186-2/+378
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add Ubiquiti LED driverDavid Bauer2021-02-185-0/+242
| | | | | | | | | | | Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED controller based on the Holtek HT32F52241 MCU. This driver is initially used by the Ubiquiti UniFi 6 LR, however judging from FCC pictures the MCU is also found on the U6-Mesh as well as the U6-Extender. Signed-off-by: David Bauer <mail@david-bauer.net>
* bcm63xx: add kernel 5.10 supportÁlvaro Fernández Rojas2021-02-17141-0/+21640
| | | | | | Runtime-tested on Comtrend AR-5387un. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: update kernel 5.10 to 5.10.16Daniel Golle2021-02-173-4/+4
| | | | | | Compile and runtime-tested on mediatek/mt7622 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* build: fix build with CONFIG_STRIP_KERNEL_EXPORTSFelix Fietkau2021-02-171-3/+3
| | | | | | Only use symtab.h on the final kernel link Signed-off-by: Felix Fietkau <nbd@nbd.name>
* openssl: bump to 1.1.1jEneas U de Queiroz2021-02-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes 4 security vulnerabilities/bugs: - CVE-2021-2839 - SSLv2 vulnerability. Openssl 1.1.1 does not support SSLv2, but the affected functions still exist. Considered just a bug. - CVE-2021-2840 - calls EVP_CipherUpdate, EVP_EncryptUpdate and EVP_DecryptUpdate may overflow the output length argument in some cases where the input length is close to the maximum permissable length for an integer on the platform. In such cases the return value from the function call will be 1 (indicating success), but the output length value will be negative. - CVE-2021-2841 - The X509_issuer_and_serial_hash() function attempts to create a unique hash value based on the issuer and serial number data contained within an X509 certificate. However it was failing to correctly handle any errors that may occur while parsing the issuer field (which might occur if the issuer field is maliciously constructed). This may subsequently result in a NULL pointer deref and a crash leading to a potential denial of service attack. - Fixed SRP_Calc_client_key so that it runs in constant time. This could be exploited in a side channel attack to recover the password. The 3 CVEs above are currently awaiting analysis. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* gettext-full: update to 0.21Rosen Penev2021-02-1610-120/+395
| | | | | | | | | | | | | | Add m4 patch to avoid conflict with tools/autoconf-archive. Add build parallel as it seems to work now. Remove a bunch of uClibc-ng hacks as it is not in the tree anymore. Format security patch was fixed upstream. Refreshed other patches. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: 5.10: refresh patchesAdrian Schmutzler2021-02-165-36/+41
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.10: add missing partitions doc syntax commitAdrian Schmutzler2021-02-161-0/+324
| | | | | | | This patch has been added to 5.4, but not been copied to 5.10: 7495acb55573 ("kernel: backport mtd commit converting partitions doc syntax") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: hack-5.10: make UDP tunneling user-selectableAdrian Schmutzler2021-02-161-0/+11
| | | | | | | | | | | | | | | | This applies another patch from 5.4 to 5.10 as well: de09355f74c3 ("kernel/hack-5.4: make UDP tunneling user-selectable") UDP tunneling support isn't user-selectable, but it's required by WireGuard which is, for the time being, an out-of-tree module. We currently work around this issue by selecting an unrelated module which depends on UDP tunnelling (VXLAN). This is inconvenient, as it implies this unrelated module needs to be built-in when doing a monolithic build. Fix this inconvenience by making UDP tunneling user-selectable in the kernel configuration. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.4: fix .patch file extensionAdrian Schmutzler2021-02-161-0/+0
| | | | | | | File extension was truncated for pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.10: fix busy wait loop in mediatek PPE codeAdrian Schmutzler2021-02-161-1/+1
| | | | | | | | | | | | | | Reapply changes added to 5.4 but not copied to 5.10: 3da4acaa7bba ("kernel: fix busy wait loop in mediatek PPE code") The intention is for the loop to timeout if the body does not succeed. The current logic calls time_is_before_jiffies(timeout) which is false until after the timeout, so the loop body never executes. time_is_after_jiffies(timeout) will return true until timeout is less than jiffies, which is the intended behavior here. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* generic: ar8216: update version switch for of_get_phy_mode fixAdrian Schmutzler2021-02-161-2/+2
| | | | | | | | | | | | | Kernel has changed the of_get_phy_mode API in commit 0c65b2b90d13 ("net: of_get_phy_mode: Change API to solve int/unit warnings"). This is already included in kernel 5.5, so fix the version switch (though this will not actually matter for the versions we support). Similar driver adjustments to account for the API change will probably be necessary to various other local drivers. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* generic: ar8216: fix kernel 5.10 compile errorDavid Bauer2021-02-161-0/+8
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: add linux 5.10 supportFelix Fietkau2021-02-16159-11/+31996
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: make zstd initramfs selectableFelix Fietkau2021-02-162-1/+5
| | | | | | fix typo in kernel initramfs zstd compression option Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: build kernel image before building modules/packagesFelix Fietkau2021-02-161-3/+3
| | | | | | | This is needed for linux 5.10, where modules.builtin is generated from vmlinux.o Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: reorder more BuildPackages lines to deal with ABI_VERSIONFelix Fietkau2021-02-167-11/+13
| | | | | | | After the ABI version rework, packages need to be declared in the order of their dependencies, so that dependent packages will use the right ABI version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath10k-ct: switch to 5.10Álvaro Fernández Rojas2021-02-167-103/+79
| | | | | | | Let's switch to 5.10 now that mac80211 has been updated. Runtime-tested on ipq806x (Netgear R7800). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm4908: add bcm_sf2 fixes for the 5th GPHYRafał Miłecki2021-02-162-0/+76
| | | | | | | This allows using the last integrated PHY (and so e.g. WAN port on the ASUS GT-AC5300). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* build: IS_TTY is now set according to GNU Make's MAKE_TERMOUTR. Diez2021-02-151-1/+1
| | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Fixes: FS#2086 The logic for IS_TTY was broken, because it was testing stdin instead of stdout. MAKE_TERMOUT was introduced in GNU Make version 4.1 (05 Oct 2014), so it should be available everywhere nowadays. Signed-off-by: R. Diez <rdiezmail-openwrt@yahoo.com>
* build/prereq: require make 4.1 or laterPaul Spooren2021-02-152-3/+3
| | | | | | | | | | | | FS#2086 "IS_TTY in the makefile is broken" reports flawed detection of stdout piping to a file. The issue describes how e.g. terminal color codes and up in log files if running make like `make > log.txt`. The proposed solution uses the make variable "MAKE_TERMOUT", which was introduced in make 4.1. All major distributions seem to updated to 4.1 or later, so this ideally dosen't break anything. Signed-off-by: Paul Spooren <mail@aparcar.org>
* util-linux: move libuuid BuildPackage line further up to fix ABI versioningFelix Fietkau2021-02-161-1/+3
| | | | | | | After the ABI version rework, packages need to be declared in the order of their dependencies, so that dependent packages will use the right ABI version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: fix getting ABI version for binary packages from the same source packageFelix Fietkau2021-02-151-1/+1
| | | | | | | We can't rely on the .version file being created yet, so use package variables to get it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: Update to version 5.10.16-1Hauke Mehrtens2021-02-1512-185/+19
| | | | | | The removed patches were applied upstream. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Refresh patches againHauke Mehrtens2021-02-1514-110/+124
| | | | | | | A wrong quilt configuration was used last time. Fixes: ed1e234d87fc ("mac80211: refresh patches") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm4908: fix GPIOs support by limiting them to 64Rafał Miłecki2021-02-151-0/+23
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: use DTS patches sent upstreamRafał Miłecki2021-02-155-33/+145
| | | | | | | | There are 2 new patches: 1. Netgear R8000P switch ports 2. Netgear R8000P LEDs Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* build: filter out own packages on package version checkFelix Fietkau2021-02-151-2/+2
| | | | | | | This was accidentally dropped in 27a4a71c2408 ("metadata: handle ABI version rebuild tracking for transient dependencies") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/fakeroot: fix build regression on macOSFelix Fietkau2021-02-151-0/+42
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: update to the latest version, set ABI_VERSION dynamicallyFelix Fietkau2021-02-151-6/+8
| | | | | | 2537be018587 cmake: add a possibility to set library version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: only overwrite ABI version for provided packages when base version ↵Felix Fietkau2021-02-151-5/+5
| | | | | | | | changed Should avoid some spurious rebuilds Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Mostly revert "build: add support for fixing up library soname"Felix Fietkau2021-02-154-84/+0
| | | | | | | | | This reverts commit b12288fa69b171f7c9405518c9bed3581a06f7ce. The patchelf approach is too fragile, and the only users of this have been converted to make patching unnecessary Leave the abi_version_str variable in place in rules.mk Signed-off-by: Felix Fietkau <nbd@nbd.name>
* wolfssl: use libtool patch for PKG_ABI_VERSIONFelix Fietkau2021-02-151-1/+1
| | | | | | Makes it unnecessary to patch .so files after build Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: add support for patching libtool to include ABI version in sonameFelix Fietkau2021-02-151-0/+10
| | | | | | Use the version from PKG_ABI_VERSION Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: use build system variable to specify ABI versionFelix Fietkau2021-02-151-4/+5
| | | | | | This removes the need to patch it afterwards Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm4908: add USB packages to the DEFAULT_PACKAGESRafał Miłecki2021-02-151-0/+2
| | | | | | | All known 41 BCM4908 devices have USB ports so it makes sense to include those packages by default. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: fix backport of PMB driverRafał Miłecki2021-02-151-0/+8
| | | | | | | Missing Makefile change was preventing kernel from actually compiling the driver. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: drop ofpart patch dropped from upstream mtd treeRafał Miłecki2021-02-156-236/+653
| | | | | | It stopped ofpart_parser_init() from being called Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport "ofpart" mtd parser upstream quirks supportRafał Miłecki2021-02-156-29/+77
| | | | | | | | | | This adds quirks support to the "ofpart" parser. It's required to support fixed partitions that require some extra logic. Right now only BCM4908 binding is supported (BCM4908 requires detecting currently used "firmware" partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: fix busy wait loop in mediatek PPE codeIlya Lipnitskiy2021-02-151-1/+1
| | | | | | | | | | | The intention is for the loop to timeout if the body does not succeed. The current logic calls time_is_before_jiffies(timeout) which is false until after the timeout, so the loop body never executes. time_is_after_jiffies(timeout) will return true until timeout is less than jiffies, which is the intended behavior here. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* wolfssl: use dynamic ABI_VERSION depending on the configuration and package ↵Felix Fietkau2021-02-151-1/+3
| | | | | | version Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: use PKG_ABI_VERSIONFelix Fietkau2021-02-151-1/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* fakeroot: fix to work with glibc 2.33Ilya Lipnitskiy2021-02-151-0/+145
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following commit removed _STAT_VER definitions from glibc: https://sourceware.org/git/?p=glibc.git;a=commitdiff;h=8ed005daf0ab03e142500324a34087ce179ae78e That subsequently broke fakeroot: https://bugs.archlinux.org/task/69572 https://bugzilla.redhat.com/show_bug.cgi?id=1889862#c13 https://forum.openwrt.org/t/unable-to-build-toolchain-fakeroot-fails-perhaps-others-after-it/87966 Make the patch based on Jan Pazdziora's suggestion from here: https://lists.fedoraproject.org/archives/list/devel@lists.fedoraproject.org/message/SMQ3RYXEYTVZH6PLQMKNB3NM4XLPMNZO/ Add wrappers for newly exported symbols in glibc. Apply patch from Debian to fix warnings in fts_read and fts_children: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=676428 https://sources.debian.org/patches/fakeroot/1.25.3-1.1/eglibc-fts-without-LFS/ Fix __xmknod{,at} dev pointer argument. Switch default to assume * and not the absence of *. On glibc 2.33+, there is no definition for these functions in header files, so the compile test doesn't work. But, we can default to using the pointer (as is the case with newer glibc), and use the header file on older platforms to fail the test and use no pointer. Tested on my x86_64 Arch Linux machine, fakeroot unit tests pass. Also tested by building various .ipks and examining the tar contents, to ensure that the owner uid/gid was 0/0. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* tools/patchelf: bump to use latest masterIlya Lipnitskiy2021-02-151-4/+5
| | | | | | | | | | | | | | | | | | | Recent ABI_VERSION commits make use of patchelf. It was discovered that with patchelf 0.10(and even 0.12) various big endian targets fail to link against libubox SO that was processed through patchelf. Using latest master patchelf fixes those link errors. Potential commits affecting big-endian processing https://github.com/NixOS/patchelf/commit/884eccc4f061a3dbdbe63a4c73f1cc9bbf77fa7d https://github.com/NixOS/patchelf/commit/d148bae6c1291b93d660a156a1756670069cd8cc Recent builds with failures: http://buildbot.openwrt.org/master/images/builders/lantiq%2Fxrx200/builds/682 http://buildbot.openwrt.org/master/images/builders/ath79%2Fmikrotik/builds/449 Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* odhcpd: setup dhcpv4 server automagicallyDaniel Golle2021-02-152-6/+26
| | | | | | | | | | Automatically setup dhcpv4 server just like it's done for dhcpv6. To select whether odhcpd or dnsmasq are serving DHCPv4 requests there still is the 'maindhcp' option. To make things less confusing, make sure things really work out-of-the-box in case dnsmasq is not even installed at the time the uci-defaults script is being run. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Revert "wolfssl: use dynamic ABI_VERSION depending on the configuration and ↵Hauke Mehrtens2021-02-151-3/+1
| | | | | | | | | | | | | | | | package version" This fixes the build on MIPS BE like ath25 and ath79 target. We get this error message when linking libwolfssl: mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so when searching for -lwolfssl mips-openwrt-linux-musl/bin/ld: cannot find -lwolfssl collect2: error: ld returned 1 exit status This reverts commit 2591c83b3406c16d3c1cd2dc7fa59c3c1b901d3c. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "libubox: use PKG_ABI_VERSION"Hauke Mehrtens2021-02-151-4/+1
| | | | | | | | | | | | This fixes the build on MIPS BE like ath25 and ath79 target. We get this error message when linking libubox: mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags' mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so when searching for -lubox This reverts commit f421fefa8a34319c5ff5dcc1af39d6311ec1ad1e. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: mark toggle input on EX6150 as a switchKurt Roeckx2021-02-151-0/+1
| | | | | | | | | The Netgear EX6150 has an Access Point/Extender switch. Set it as an EV_SW. Otherwise when it's set to Access Point, it will trigger failsafe mode during boot. Fixes: FS#3590 Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
* Revert "imx6: bootscript-apalis: make it working on v2021.01 release"Petr Štetiar2021-02-141-4/+2
| | | | | | | | This reverts commit 4968fc8fb110612018af3ba2836be1b4744346e2 as the bump to v2021.01 needs swig on the host for pylibfdt which is needed by dtoc tool to generate .h/.c files from DTBs in SPL for mx6cuboxi_config. Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-17 14:07:11 +0000