aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* mac80211: rt2x00: import upstream changes and rebase our patchesDaniel Golle2017-03-3049-189/+1676
| | | | | | | | Some of our local patches have been accepted upstream. And there are some more relevant changes (mostly for rt2800usb). Import them and rebase our remaining local patches on top. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ar71xx: Compex WPJ563 supportChristian Mehlis2017-03-3012-0/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc) - RAM: 128 MiB - Storage: 16MB NOR flash - Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO - Ethernet: 2x1G Tested and working: - ethernet / switch / lan / wan - 2.4GHz SoC wifi - PCIe - leds - buzzer Ramload: - tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin - bootm 0x84000000 Install: - tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin - erase 0x9f030000 +$filesize - erase 0x9f680000 +1 - cp.b $fileaddr 0x9f030000 $filesize Erasing 0x9f680000 is required because uboot defines "bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot the higher address. I think the 16 mb flash are intended to be used as 8+8mb for a fallback image. In my hardware only the lower address has a bootable image. But to make sure future hardware will boot lede too, I erase one block, so uboot will skip this address. Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar8327: Add workarounds for AR8337 switch.Vittorio Gambaletta2017-03-302-1/+62
| | | | | | | | | | | | | | | | RGMII RX delay setting needs to be always specified for AR8337 to avoid port 5 RX hang on high traffic / flood conditions. Also, the HOL registers that set per-port and per-packet-priority buffer sizes are updated with the reduced values suggested by the QCA switch team. Finally, AR8327 reserved register fixups are disabled for the AR8337. This patch is adapted from the Code Aurora QSDK, but with magic values mapped to proper defines. Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
* dnsmasq: use logical interface name for dhcp relay configKarl Vogel2017-03-291-1/+2
| | | | | | | | | The relay section should use the logical interface name and not the linux network device name directly. This to be consistent with other sections of the dnsmasq config where 'interface' means the logical interface. Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
* ar71xx: drop default CONSOLE valuesJohn Crispin2017-03-291-4/+0
| | | | | | Compex boards dont need to set these as they are default. Signed-off-by: John Crispin <john@phrozen.org>
* fstools: update to latest git HEADJohn Crispin2017-03-291-3/+3
| | | | | | | 20c16fc cmake: Make blockd link against libjson-c 92b4c2c libfstools: add basic documentation of mount functions Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: move Compex WPJ342 to generic build targetChristian Mehlis2017-03-293-7/+10
| | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: move Compex WPJ344 to generic build targetChristian Mehlis2017-03-293-7/+10
| | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: move Compex WPJ531 to generic build targetChristian Mehlis2017-03-293-7/+10
| | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: move Compex WPJ558 to generic build targetChristian Mehlis2017-03-293-7/+10
| | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* kernel: add w83627hf-wdt watchdog timer modulePhilip Prindeville2017-03-291-0/+15
| | | | | | | | | This is a 3rd party chipset which is not present on all Intel reference designs, so make it a module rather than baked in (this will also alleviate conflicts with drivers which also detect some of the same chipsets). Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* kernel: kmod packaging for Intel 10G ethernet ixgbe driverPhilip Prindeville2017-03-292-0/+35
| | | | | | | A lot of Ivybridge and Haswell servers have the 82598/82599 Ethernet controllers. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* firewall: document rules for IPSec ESP/ISAKMP with 'name' optionYousong Zhou2017-03-282-15/+16
| | | | | | | | | | These are recommended practices by REC-22 and REC-24 of RFC6092: "Recommended Simple Security Capabilities in Customer Premises Equipment (CPE) for Providing Residential IPv6 Internet Service" Fixes FS#640 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ipq8064: fix dwc3-of-simple module unloadingThomas Reifferscheid2017-03-281-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without patch unloading the dwc3-of-simple module went stuck after successfully removing hcd.1 during the hcd.0 removal: root@LEDE:/# rmmod dwc3-of-simple [ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 21.391931] usb usb4: USB disconnect, device number 1 [ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 21.406685] usb usb3: USB disconnect, device number 1 [ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 21.422521] usb usb2: USB disconnect, device number 1 followed by nothing. Sometimes a stall CPU was detected, or a kernel panic, or a reboot occurred after a couple of minutes. At the same time unloading the dwc3 module followed by dwc3-of-simple module was working repeatedly. root@LEDE:/# rmmod dwc3 [ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 53.827412] usb usb4: USB disconnect, device number 1 [ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 53.842314] usb usb3: USB disconnect, device number 1 [ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 53.857882] usb usb2: USB disconnect, device number 1 [ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 53.873696] usb usb1: USB disconnect, device number 1 [ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered root@LEDE:/# rmmod dwc3-of-simple root@LEDE:/# For the non-working case, the code was stuck in a readl() in http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91 because http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126 was disabling the wrong clocks when removing hcd.1 (it was disabling the clock of hcd.0). That's why the readl() went stuck when removing hcd.0 The patch however addresses the clock assignment from the .dtsi file. Most probably it went into openwrt here: https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261 copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116 Now unloading and repeated module loading is working just fine, no matter if you'd remove dwc3-of-simple or dwc3. root@LEDE:/# rmmod dwc3-of-simple [ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 24.089765] usb usb4: USB disconnect, device number 1 [ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 24.104522] usb usb3: USB disconnect, device number 1 [ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 24.120396] usb usb2: USB disconnect, device number 1 [ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 24.135948] usb usb1: USB disconnect, device number 1 [ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered root@LEDE:/# Fixes: dwc3-of-simple module unloading Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
* ipq8064: Fix dwc3 module unloadingThomas Reifferscheid2017-03-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow module unloading by fixing a mistake. qcom_dwc3_phy_write_readback() is expecting (phy, offset, mask, value) while the mistake was calling it with (phy, offset, value, mask) The patch is swapping value and mask. Without the patch unloading the dwc3 module was showing a write to QSCRATCH failed and repeated module loading was failing: root@LEDE:/# rmmod dwc3 [ 19.167998] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 19.168084] usb usb4: USB disconnect, device number 1 [ 19.173371] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 19.177134] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 19.182960] usb usb3: USB disconnect, device number 1 [ 19.189023] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 19.192989] qcom-dwc3-usb-phy 110f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED [ 19.199064] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 19.205912] usb usb2: USB disconnect, device number 1 [ 19.211611] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 19.215905] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 19.221751] usb usb1: USB disconnect, device number 1 [ 19.227307] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered [ 19.231795] qcom-dwc3-usb-phy 100f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED root@LEDE:/# modprobe dwc3 [ 29.583343] phy phy-100f8830.phy.4: phy init failed --> -110 [ 29.583399] dwc3 10000000.dwc3: failed to initialize core [ 29.588169] dwc3: probe of 10000000.dwc3 failed with error -110 [ 29.652943] phy phy-110f8830.phy.2: phy init failed --> -110 [ 29.652988] dwc3 11000000.dwc3: failed to initialize core [ 29.657735] dwc3: probe of 11000000.dwc3 failed with error -110 root@LEDE:/# With patch repeated module unloading and loading is working good: root@LEDE:/# rmmod dwc3 [ 22.622214] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 22.622298] usb usb4: USB disconnect, device number 1 [ 22.627401] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 22.631492] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 22.637054] usb usb3: USB disconnect, device number 1 [ 22.643721] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 22.647421] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 22.652910] usb usb2: USB disconnect, device number 1 [ 22.659219] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 22.662768] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 22.668604] usb usb1: USB disconnect, device number 1 [ 22.674803] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered root@LEDE:/# modprobe dwc3 [ 25.404592] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 25.404694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 25.409444] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010 [ 25.416589] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x10000000 [ 25.426509] hub 1-0:1.0: USB hub found [ 25.431626] hub 1-0:1.0: 1 port detected [ 25.435472] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 25.439206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 25.444573] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 25.452926] hub 2-0:1.0: USB hub found [ 25.460420] hub 2-0:1.0: 1 port detected [ 25.525037] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 25.525099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 25.529750] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010 [ 25.537002] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x11000000 [ 25.546583] hub 3-0:1.0: USB hub found [ 25.551997] hub 3-0:1.0: 1 port detected [ 25.555734] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 25.559621] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 25.564942] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 25.573063] hub 4-0:1.0: USB hub found [ 25.580842] hub 4-0:1.0: 1 port detected root@LEDE:/# Fixes: dwc3 module unloading Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
* mac80211: ath10k: allow failure getting board id via otpHannu Nyman2017-03-281-0/+11
| | | | | | | | | | | | | | | ath10k tries to fetch board id via otp, but that fails for many chips like QCA988x, QCA9984 etc. Recent commit cc189c0b7f removed the earlier hack that had allowed QCA radios to work, as that hack was incompatible with the new wifi chips being introduced to the source tree. Restore functionality for the existing wifi chips by modifying the return value of the 'board id via otp' function to a value that is recognised as a harmless error, so that name evaluation continues by using the board file. Patch originally suggested by Christian Lamparter in forum discussion. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ramips: fix pcie irq mapping for mt7621 on v4.9John Crispin2017-03-281-10/+18
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* bcm53xx: put kernel into TRX when building initramfs imagesRafał Miłecki2017-03-271-0/+25
| | | | | | | | | | | Many (most?) devices can't boot raw kernel using tftp and probably none allows flashing it. It's way more usable to have TRX with kernel containing initrams as such an image can be actually flashed. An exception are Buffalo devices which have recovery mode with support for booting kernels over TFTP. For them keep building default images. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: wpj531: fix GPIOs for LEDLeon M. George2017-03-271-4/+4
| | | | | | /sys/devices/platform/leds-gpio/leds/ was not initialised with working LEDs. Signed-off-by: Leon M. George <leon@georgemail.eu>
* ipq8064: enable 2nd USB port on R7500Thomas Reifferscheid2017-03-272-4/+6
| | | | | | | | | Makes use of the syscon tcsr and enables both USB ports. Cleans up qcom-ipq8064.dtsi from previous attempts. Fixes FS#497 Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
* kernel: Fix F2FS module dependenciesShane Peelar2017-03-271-0/+1
| | | | | | F2FS depends on the crc32_generic module (NOT crc32c_generic) Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>
* kernel: Add kmod-crypto-crc32 (crc32_generic.ko)Shane Peelar2017-03-271-0/+11
| | | | | | | This is needed for F2FS support (it depends on crc32_generic, not crc32c_generic). Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>
* package/boot/uboot-kirkwood: fix build errors for nsa310 and nsa325Paul Wassi2017-03-273-54/+14
| | | | | | | With upstream changes, the last update to U-Boot 2017.03 broke the nsa310 and nsa325 targets. Also fix some redefines. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* lantiq: align falcon code with ar9-vr9 codeStefan Koch2017-03-271-70/+3
| | | | Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
* lantiq: cleanup code ar9-vr9 partsStefan Koch2017-03-272-155/+131
| | | | | | | | | | - remove unused code within 500-ar9_vr9.patch - fixed return of IFX_ERROR (solves SIGSEGV in asterisk at failure) - align it a bit with 400-falcon.patch - remove 600-kernel-4.9.patch since changed parts are removed during cleanup Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
* ipq806x: tsens: convert degrees to millicelsiusPavel Kubelun2017-03-272-79/+79
| | | | | | | | | | Current driver shows temp in full degrees while other apps await it to be in millidegrees. Initially the driver represents termal data in millidegrees but then it gets divided by TSENS_FACTOR. So lets just set it to '1'. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: add ipq806x specific tsens driverPavel Kubelun2017-03-275-106/+1445
| | | | | | | | | | | | | | | | | Current upstream driver doesnt fully support ipq806x devices ipq806x has 11 sensors, the upstream one doesn't allow to check sensors 0-4, only 5-10. A specific driver for ipq806x has been found in Qualcomm SDK repo. https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c089e464cd7ce652419a0dc44d7959ce4d24b8a5 https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c23d94b702c4182862e7f5051a2b7d00bb922a29 https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=742f3684b62a6b9f082cb49404b1a92dc0b16bf5 https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c0a9b2e2a382c152fa128f5b864c800dd6dfb311 Merging it into LEDE with this commit. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* kernel: add arm64 erratums into configHauke Mehrtens2017-03-262-0/+25
| | | | | | | | Deactivate all the ARM64 erratums by default. The target code should activate them if needed. This fixes a problem with a new erratum added in kernel 4.9.17 breaking brcm2708. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: update spi driver to upstream versionHauke Mehrtens2017-03-265-82/+855
| | | | | | These patches are backported from upstream Linux kernel. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update kernel 4.9 to 4.9.17Hauke Mehrtens2017-03-2652-500/+84
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update kernel 4.4 to 4.4.56Hauke Mehrtens2017-03-2615-58/+25
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iw: enable MESH ID in scan outputMatthias Schiffer2017-03-251-4/+5
| | | | | | | | Make scan output useful for 802.11s meshes. The common print_ssid function is used, so this doesn't add any additional code. Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* busybox: vi: backporting patches to fix ZZ and :x commandYousong Zhou2017-03-253-1/+154
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* brcm2708: backport upstream ARM dts commitsRafał Miłecki2017-03-2420-26/+1211
| | | | | | | | | | | | This gets us in sync with dts from kernel 4.11. Two patches were already backported earlier. I decided to use 03x prefix as it's kind of similar to the 3xx prefix: 3xx - architecture specific patches It isn't any documented or strict rule though. We don't need to stick to it if we hit any problems. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
* lantiq: vr9 fxs support: remove unused wdog declarations and initializersStefan Koch2017-03-242-60/+4
| | | | | | | | | | modify 0152-lantiq-VPE.patch from commit e0229a16b000 ("lantiq: added support for VPE1") - remove wdog function declarations from header (asm/vpe.h) - remove wdog command line init functions (vpe.c) Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
* lantiq: vr9 fxs support: remove soft-watchdog functionalityStefan Koch2017-03-242-340/+0
| | | | | | | | | - remove patched header (vpe.h) because kernel already provides one (asm/vpe.h) - remove module softdog_vpe since watchdog functionality is unused - remove module softdog_vpe from Makefile Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
* lantiq: remove residual watchdog parts from ltq-vmmcStefan Koch2017-03-241-3/+94
| | | | | | | | | | | | modify 500-ar9_vr9.patch from commit 29367aac42d6 ("lantiq: ltq-vmmc add support for ar9-vr9") - remove unused dependencies to external watchdog functions (wdog setup is already disabled) - using header file from kernel (asm/vpe.h) instead patched file (vpe.h) - cleanup whitspace warning Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
* ramips: fix Xiaomi MiWiFi Nano firmware partition sizeMathias Kresin2017-03-241-1/+1
| | | | | | | | | | Even the commit message of the patch adding support for the MiWiFi Nano says that a 16 MB flash chip is used. Extend the firmware partition to make use of all available flash space. Fixes: FS#622 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath10k-firmware: do not select the qca988x by defaultMathias Kresin2017-03-241-1/+0
| | | | | | | | Do not select the qca988x by default as soon as kmod-ath10k is selected. We do support more ath10k chips than the qca988x in the meantime, so this dependency doesn't make sense any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: select ath10k firmware explicitMathias Kresin2017-03-242-3/+3
| | | | | | Do not rely on the default firmware selected by ath10k. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: fix Netgear X4 R7500 ath10k firmware selectionThomas Reifferscheid2017-03-241-1/+1
| | | | | | | Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches the ath10k chipset Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
* lantiq: fix pci with kernel 4.9Mathias Kresin2017-03-241-2/+3
| | | | | | | | Commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists") changed the controller list from reverse to straight order. Use the last entry in the controller list to get the fist conroller of the system. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: add MIPS pci fix send upstreamMathias Kresin2017-03-241-0/+31
| | | | | | | | | | | | | | | Upstream commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists") changed the controller list from reverse to straight order without taking care of the changed order for the scan of the recorded PCI controllers. Traverse the list in reverse order to restore the former behaviour. This patches fixes the following PCI error on lantiq: pci 0000:01:00.0: BAR 0: error updating (0x1c000004 != 0x000000) Signed-off-by: Mathias Kresin <dev@kresin.me>
* brcm2708: rename all patches from raspberrypi git tree to use 950 prefixRafał Miłecki2017-03-24196-0/+0
| | | | | | | | | | | | | | | | | | Right now all brcm2708 patches are extracted from the non-mainline raspberrypi/linux git tree. Many of them are hacks and/or are unneeded in LEDE. Raspberry Pi is getting better and better mainline support so it would be nice to finally start maintaining patches in a cleaner way: 1) Backport patches accepted in upstream tree 2) Start using upstream drivers 3) Pick only these patches that are needed for more complete support Handling above tasks requires grouping patches - ideally using the same prefixes as generic ones. It means we should rename existing patches to use some high prefix. This will allow e.g. use 0xx for backported code. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
* gdb: fix invalid sigprocmask callYousong Zhou2017-03-242-1/+44
| | | | | | Fixes FS#637 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: image: fix indentationPiotr Dymacz2017-03-234-553/+553
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for P&W R602N and CPE505NPiotr Dymacz2017-03-2313-8/+285
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-LINK TL-WR840N v2 and v3Vaclav Svoboda2017-03-2313-2/+115
| | | | | | | | | | | | | | This patch adds support for the TP-LINK TL-WR840N v2 and v3. - SoC: Qualcomm QCA9533-BL3A (650 MHz) - RAM: 32 MiB (Zentel A3S56D40GTP) - Flash: 4 MiB (v2: Macronix MX 25L323F) (v3: Winbond 25Q32FVSIG) - LAN: 4x 100M - WAN: 1x 100M Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ar71xx: add support for MikroTik hAP acRyan Mounce2017-03-2311-3/+175
| | | | | | | | | | | This patch adds initial support for the MikroTik RouterBOARD hAP ac (RB962UiGS-5HacT2HnT). All functions are supported except: -SFP cage (eth1) is not working -WLAN LEDs are not working Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: add support for MikroTik hAP ac liteRyan Mounce2017-03-2311-10/+47
| | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hAP ac lite (RB952Ui-5ac2nD). The hAP ac lite is nearly identical to the hAP, with an added QCA9887 5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 14:45:20 +0000