aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.10 to 5.10.30Rui Salvaterra2021-04-1614-87/+23
| | | | | | | | | | | | | | | | | | | | | Deleted (reverse-applicable): mvebu/patches-5.10/101-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch Automatically refreshed: bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch generic/backport-5.10/610-v5.13-02-netfilter-Fix-fall-through-warnings-for-Clang.patch generic/backport-5.10/610-v5.13-10-netfilter-nftables-update-table-flags-from-the-commi.patch generic/hack-5.10/204-module_strip.patch generic/hack-5.10/902-debloat_proc.patch generic/pending-5.10/203-kallsyms_uncompressed.patch generic/pending-5.10/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch generic/pending-5.10/920-mangle_bootargs.patch mediatek/patches-5.10/115-dts-bpi64-add-snand-support.patch mediatek/patches-5.10/602-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-MT7622.patch mediatek/patches-5.10/900-dts-mt7622-bpi-r64-aliases-for-dtoverlay.patch ramips/patches-5.10/323-mt7621-memory-detect.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ath79: mikrotik: enable SFP on RB922UAGS-5HPaCDRoger Pueyo Centelles2021-04-164-2/+51
| | | | | | | | | | | | | | | | This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD. GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable or disable transmission, but no change is observed. Therefore, it is left as output high to ensure the SFP module is forced to transmit. Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD 1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers 950 Mbps symmetric. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* gemini,layerscape,oxnas: don't disable option CONFIG_BPF_SYSCALLTony Ambardar2021-04-165-5/+0
| | | | | | | | Respect the generic kernel config setting, which is "enabled" tree-wide, as previously done for sunxi. Ref: 247ef4d98bab ("sunxi: enable CONFIG_BPF_SYSCALL and CONFIG_EMBEDDED") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: fix 10 Mbit PLL data for TP-Link EAP2xxDavid Bauer2021-04-151-0/+1
| | | | | | | | | | | Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP boards using a AR8033 SGMII PHY. Otherwise, 10 Mbit/s links do not transfer data. Reported-by: Tom Herbers <freifunk@tomherbers.de> Tested-by: Tom Herbers <freifunk@tomherbers.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix 10 Mbit PLL data for UniFi ACDavid Bauer2021-04-151-0/+2
| | | | | | | Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite / Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix link mode support list on UniFi ACDavid Bauer2021-04-152-0/+72
| | | | | | | | | | | | | | | | | | | | This fixes incorrect supported link modes indicated when using ethtool on the Ubiquiti UniFi AC lite / LR / Mesh. eroot@OpenWrt:~# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full The reason for this is, that since kernel 5.4 the PHY capabilities are read dynamically from the PHY. As Ubiquiti leaves the PHY in a wrong state, the capabilities of the SGMII side of the PHY are read. As a side effect, 10 Mbit/s link modes did not work on these boards. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips/mediatek: import a patch fixing bug in flow-offloadingDaniel Golle2021-04-151-0/+24
| | | | | | | | | | | From Frank Wunderlich <frank-w@public-files.de>: Issue were traffic problems after a while with increased ping times if flow offload is active. It turns out that key_offset with cookie is needed in rhashtable_params and head_offset was defined twice. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* libsemanage: fix pkgconfig pathsRosen Penev2021-04-151-1/+3
| | | | | | The pkgconfig file currently points to host paths. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* uboot-sunxi: update ATF dependencies for 3 boardsZoltan HERPAI2021-04-151-3/+3
| | | | | | | Fix 3 board definitions that were missed in the process of moving to the a64/h6 ATF blobs. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ramips: gpio-ralink: use ngpios, not ralink,num-gpiosIlya Lipnitskiy2021-04-1513-29/+51
| | | | | | | | | | | | | | | | DTS properties that match *-gpios are treated specially. Use ngpios instead, as most GPIO drivers upstream do. Fixes 5.10 DTS errors such as: OF: /palmbus@300000/gpio@600: could not find phandle Fixes DTC warnings such as: Warning (gpios_property): /palmbus@300000/gpio@600:ralink,num-gpios: Could not get phandle node for (cell 0) Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Cc: Daniel Golle <daniel@makrotopia.org>
* ramips: rt288x: replace hack with a kconfig changeIlya Lipnitskiy2021-04-152-45/+32
| | | | | | | | | Use an existing kernel config symbol to fix devices whose ramstart is not zero. See upstream patch message for more details. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Cc: Tobias Wolf <dev-NTEO@vplace.de> Cc: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7530 swconfig: fix race condition in register accessDENG Qingfang2021-04-151-6/+10
| | | | | | | | | | | | | | | | The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and does not hold a lock, which causes a race condition when multiple threads try to access a register, they may get unexpected results. To avoid this, handle the MDIO lock manually, and use the unlocked __mdiobus_{read,write} in the critical section. This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN operation and the swconfig LED link status poll race between each other. [1] https://forum.openwrt.org/t/mysterious-vlan-ids-on-mt7621-device/64495 Signed-off-by: DENG Qingfang <dqfext@gmail.com>
* ramips: drop obsolete arcs_cmdline override patchIlya Lipnitskiy2021-04-151-21/+0
| | | | | | | | CONFIG_MIPS_CMDLINE_FROM_DTB is set to 'y' for all ramips targets already, which will ensure that the value of 'bootargs' will take precedence over whatever is in arcs_cmdline. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* firmware-utils: tplink-safeloader: support displaying fw infoRafał Miłecki2021-04-141-4/+127
| | | | | | | | | | Add "-i" option for reading & displaying firmware info. First it lists in-firmware partitions ("fwup-ptn"). Then it checks for human understandable partitions and prints data found in each of them. This new feature is meant for development & debug purposes. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* uci: update to the latest masterRafał Miłecki2021-04-141-3/+3
| | | | | | 4b3db11 cli: add option for changing save path Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: add pending TRX patch for "firmware" partitionRafał Miłecki2021-04-141-0/+43
| | | | | | | This fixes partitioning on Linksys EA9500. With this change only the currently used firmware MTD partition gets parsed. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: limit crypto-hw-ccp to the x86Rafał Miłecki2021-04-131-0/+1
| | | | | | | | | | | | | | CRYPTO_DEV_CCP depends on X86 or ARM64 CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64 Compiling this driver makes sense for x86 mainly. If one day support for ARM64 board with AMD Secure Processor gets added this package may be updated. Trying to build this package on bcm4908 was causing: ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: crypto: format "crypto-hw-ccp" dependenciesRafał Miłecki2021-04-131-1/+8
| | | | | | | Use multiples lines for better readability and sort lines. Suggested-by: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mkmylofw: fix blocks paddingRafał Miłecki2021-04-131-1/+1
| | | | | | | | | | | | | | | The old code didn't make sense as it was using "len" variable which was guaranteed to be always 0. Loop right above broken code is: while (len > 0) { } With this recent ALIGN macro fix this resulted in subtracting block size from 0 and calling write_out_padding() with a negative length. To calculate amount of bytes needed for padding & alignment it should be enough to use % 4. Fixes: a2f66229450d ("firmware-utils: fix few random warnings") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: zyimage: drop POSIX SOURCE definesRafał Miłecki2021-04-131-2/+0
| | | | | | | | | | This fixes: src/zyimage.c:10:0: warning: "_POSIX_SOURCE" redefined src/zyimage.c:11:0: warning: "_POSIX_C_SOURCE" redefined This change has been tested on Linux with -Wextra and on Mac OS. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* tplink-safeloader: fix C7v5 factory flashing from vendor fw > v1.1.xPetr Štetiar2021-04-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently it's not possible to flash factory images on devices shipped with vendor firmware versions 1.1.0 Build 20201120 rel. 50406 (published 2020-12-22): (curFw_ver, newFw_ver) == (1.1, 1.0) [NM_Error](nm_checkSoftVer) 00848: Firmwave not supports, check failed. [NM_Error](nm_checkUpdateContent) 01084: software version dismatched [NM_Error](nm_buildUpgradeStruct) 01188: checkUpdateContent failed. They've even following note in release notes: Note: You will be unable to downgrade to the previous firmware version after updating this firmware. This version check in vendor firmware is implemented in /usr/bin/nvrammanager binary likely as following C code[1]: sscanf(buf, "%d.%d.%*s",&upd_fw_major, &upd_fw_minor); ... if (((int)upd_fw_major < (int)cur_fw_major) || ((ret = 1, cur_fw_major == upd_fw_major && (upd_fw_minor < (int)cur_fw_minor)))) { ret = 0; printf("[NM_Error](%s) %05d: Firmwave not supports, check failed.\r\n\r\n","nm_checkSoftVer" ,0x350); } ... return ret; So in order to fix this and make it future proof it should be enough to ship our factory firmware images with major version 7 (lucky number). Tested on latest firmware version 1.1.2 Build 20210125 rel.37999: Firmwave supports, check OK. (curFw_ver, newFw_ver) == (1.1, 7.0) check firmware ok! Flashing back to vendor firmware c7v5_us-up-ver1-1-2-P1[20210125-rel37999]_2021-01-25_10.33.55.bin works as well: U-Boot 1.1.4-gbec22107-dirty (Nov 18 2020 - 18:19:12) ... Firmware downloaded... filesize = 0xeeae77 fileaddr = 0x80060000. Firmware Recovery file length : 15642231 Firmware process id 2. handle_fw_cloud 146 Image verify OK! Firmware file Verify ok! product-info:product_name:Archer C7 product_ver:5.0.0 special_id:55530000 [Error]sysmgr_cfg_checkSupportList(): 1023 @ specialId 45550000 NOT Match. Firmware supports, check OK. Firmware Recovery check ok! 1. https://gist.github.com/ynezz/2e0583647d863386a66c3d231541b6d1 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add missing patch for kernel 5.10David Bauer2021-04-131-0/+9
| | | | | | | | | When adding the patch for the missing register, the patch file for the testing kernel 5.10 was not included. Fixes commit fbbad9a9a629 ("ath79: force SGMII SerDes mode to MAC operation") Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: force SGMII SerDes mode to MAC operationDavid Bauer2021-04-132-0/+14
| | | | | | | | | | | | | | | | | The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default. This only allows for 1000 Mbit/s links, however when used with an SGMII PHY in 100 Mbit/s link mode, the link remains dead. This strictly has nothing to do with the SerDes calibration, however it is done at the same point in the QCA reference U-Boot which is the blueprint for everything happening here. As the current state is more or less a hack, this should be fine. This fixes the issues outlined above on a TP-Link EAP-225 Outdoor. Reported-by: Tom Herbers <freifunk@tomherbers.de> Tested-by: Tom Herbers <freifunk@tomherbers.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* lantiq: kernel 5.10: disable ltq-deuMathias Kresin2021-04-121-1/+1
| | | | | | | | | | For linux 5.10, kmod-ltq-deu need to be migrated to the new crypto API/framework. Leave it in tree for now and enable it only for Kernel 5.4. Maybe someone picks up the work to migrate the package. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add Linux 5.10 support as testing kernelMathias Kresin2021-04-1224-91/+338
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Following changes are made to the Lantiq kernel patches: 0001-MIPS-lantiq-add-pcie-driver.patch The pci header isn't included by the of_pci header any longer 0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch Due to the merge of grx390 and ar10 clocks, extend support to grx390 0025-NET-MIPS-lantiq-adds-xrx200-legacy.patch The do_carrier arguments was dropped from phy_link_change. The phylib has always sets the third parameter to true so the flag is always changed anyway. of_get_phy_mode() returns an error, or 0 on success, and pass a pointer, of type phy_interface_t, where the phy mode should be stored now. So far an error wasn't considered. Print at least an error message if something unexpected happens. The stuck queue is now passed to xrx200_tx_timeout (the timeout handler) but not used so far. 0028-NET-lantiq-various-etop-fixes.patch ioremap has provided non-cached semantics by default since the Linux 2.6 days and was removed with kernel version 5.6. of_get_phy_mode() returns an error, or 0 on success, and pass a pointer, of type phy_interface_t, where the phy mode should be stored now. So far an error wasn't considered. Print at least an error message if something unexpected happens. 0042-arch-mips-increase-io_space_limit.patch Move IO space extension to laniq specific file Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: copy target to kernel 5.10Mathias Kresin2021-04-1226-0/+15000
| | | | | | | | | Duplicate kernel 5.4 config and patches for kernel 5.10. Duplicate the devicetree source files as well, they need kernel 5.10 specific adjustments. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: dts: mark PCI bridges as suchMathias Kresin2021-04-123-0/+6
| | | | | | | | Use the device_type property to mark PCI host bridges as such. With linux 5.10 it is mandatory, otherwise the PCI IO space is flages as PCI memory and the PCI init fails. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ltq-adsl: add kernel 5.10 compatiblityMathias Kresin2021-04-121-0/+14
| | | | | | | The pgprot argument to __vmalloc is always PAGE_KERNEL now and was removed. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ltq-vdsl: add kernel 5.10 compatiblityMathias Kresin2021-04-121-4/+16
| | | | | | | The pgprot argument to __vmalloc is always PAGE_KERNEL now and was removed. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ltq-atm/ltq-ptm: add kernel 5.10 compatiblityMathias Kresin2021-04-123-0/+25
| | | | | | | | | | The callback handling of the tasklet API was redesigned and the macros using the old syntax renamed to _OLD. The stuck queue is now passed to ndo_tx_timeout callback but not used so far. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ltq-tapi: add kernel 5.10 compatiblityMathias Kresin2021-04-121-0/+50
| | | | | | | | | | | | | Due to SCHED_FIFO being a broken scheduler model, all users of sched_setscheduler() are converted to sched_set_fifo_low() upstream and sched_setscheduler() is no longer exported. The callback handling of the tasklet API was redesigned and the macros using the old syntax renamed to _OLD. Signed-off-by: Mathias Kresin <dev@kresin.me> ltq tapi
* lantiq: ltq-vdsl-mei: add kernel 5.10 compatiblityMathias Kresin2021-04-122-7/+71
| | | | | | proc_create_data() expects a struct of type proc_ops. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ltq-ifxos: add kernel 5.10 compatiblityMathias Kresin2021-04-121-1/+10
| | | | | | | ioremap has provided non-cached semantics by default since the Linux 2.6 days and was removed with kernel version 5.6. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: fix deferred mtdblock registrationDaniel Golle2021-04-121-12/+7
| | | | | | | | | | Check if gendisk is already up instead of trying to figure out parent mtd device (which didn't work well). Reported-by: DENG Qingfang <dqfext@gmail.com> Reported-by: Koen Vandeputte <koen.vandeputte@citymesh.com> Fixes: 2809d0000744 ("kernel: support FIT partition parser on mtdblock devices") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi: add support for Banana Pi M2 BerryZoltan HERPAI2021-04-122-0/+17
| | | | | | | | | | | | | | | | | | CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz Memory: 1GB DDR3 Storage: SDcard, native SATA Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT USB: 4x USB 2.0 Installation: Use the standard sunxi installation to an SD-card. While the board is very similar to the M2 Ultra board (the V40 is the automotive version of the R40), as both the u-boot and kernel supports them separately, and some pins are different, let's add a separate device spec. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: mikrotik: enable 2nd USB on RouterBOARD 922UAGS-5HPacDKoen Vandeputte2021-04-121-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | RB922 boards have 2 separate USB controllers: - 1 is connected to Slot Type A - 1 is connected to the mini PCIe port Enable the 2nd one too. Before: [ 5.339304] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.355053] SCSI subsystem initialized [ 5.364184] ehci-fsl: Freescale EHCI Host controller driver [ 5.372377] ehci-platform: EHCI generic platform driver [ 5.378053] ehci-platform 1b000000.usb: EHCI Host Controller [ 5.383861] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 5.391932] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000 [ 5.410730] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 5.417739] hub 1-0:1.0: USB hub found [ 5.422280] hub 1-0:1.0: 1 port detected [ 5.434007] usbcore: registered new interface driver usb-storage After: [ 5.342988] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.358687] SCSI subsystem initialized [ 5.367813] ehci-fsl: Freescale EHCI Host controller driver [ 5.375998] ehci-platform: EHCI generic platform driver [ 5.381695] ehci-platform 1b000000.usb: EHCI Host Controller [ 5.387507] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 5.395571] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000 [ 5.416050] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 5.423089] hub 1-0:1.0: USB hub found [ 5.427578] hub 1-0:1.0: 1 port detected [ 5.432432] ehci-platform 1b400000.usb: EHCI Host Controller [ 5.438254] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2 [ 5.446325] ehci-platform 1b400000.usb: irq 15, io mem 0x1b400000 [ 5.468049] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00 [ 5.475082] hub 2-0:1.0: USB hub found [ 5.479574] hub 2-0:1.0: 1 port detected [ 5.491305] usbcore: registered new interface driver usb-storage Fixes: 8f93c05a59 ("ath79: add support for MikroTik RouterBOARD 922UAGS-5HPacD") Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* uboot-mediatek: minor fixes for bpi-r64 spi-nand default envDaniel Golle2021-04-111-5/+4
| | | | | | | * check image checksums before writing to flash * only bootmenu_0...9 are working, remove bootmenu_a entry Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi: add support for H6 boards and OrangePiOnePlusZoltan HERPAI2021-04-118-2/+531
| | | | | | | | | | | | | | | | | | | | Specifications: SoC Allwinner H6 @ 1.8 Ghz DRAM 1Gb LPDDR3 Power DC 5V @ 3A Video HDMI (Type 2.0A - full) Audio HDMI, on-board microphone Network 10/100/1000Mbps Ethernet (Realtek RTL8211) Storage microSD USB 1 USB2.0 Host, 1 USB2.0 OTG Debug Serial UART Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* arm-trusted-firmware-sunxi: move to use the common tf-a build code and bump ↵Zoltan HERPAI2021-04-112-14/+20
| | | | | | | | | | | | | | | | | | | | | | | | to latest version Create a -a64 package for now. Moving to the latest ATF was tested on a SoPine A64 board. U-Boot SPL 2020.04 (Feb 19 2021 - 11:28:19 +0000) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.4(release):reboot-15854-g42b39a13d2 NOTICE: BL31: Built : 22:45:53, Feb 22 2021 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x4090a28, model: SoPine with baseboard NOTICE: PSCI: System suspend is unavailable U-Boot 2020.04 (Feb 19 2021 - 11:28:19 +0000) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: SoPine with baseboard DRAM: 2 GiB Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: add ATF variable for specifying which flavour to useZoltan HERPAI2021-04-112-2/+11
| | | | | | | In preparation for H6 support (which requires a separate ATF blob), add an envvar to the A64 boards specifying which ATF blob to use. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* toolchain: gcc: Update to version 10.3.0Hauke Mehrtens2021-04-1120-6/+6
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* valgrind: Fix compile problem with MIPS soft floatHauke Mehrtens2021-04-111-0/+68
| | | | | | | | valgrind does not compile any more when using a GCC 10 for MIPS with soft float. Just remove the parts which are generating assembler which would not work. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-envtools: support environment in spi-nand on bpi-r64Daniel Golle2021-04-111-3/+11
| | | | | | | Default to U-Boot env in UBI if root device is not mmc block device. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: mt7622: add spi-nand support for bananapi bpi-r64Oskari Lemmela2021-04-114-12/+142
| | | | | | | | | | Some of bpi-r64 boards have serial NAND attached to SPI bus. Add SD card image support for installing openwrt to it. Default to nand upgrade if root device is not mmc block device. Separate preloader and uboot images for snand are generated. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* uboot-mediatek: add spi-nand build for bananapi bpi-r64Daniel Golle2021-04-113-21/+302
| | | | | | | | Some of bpi-r64 boards have serial NAND attached to SPI bus. Build U-Boot for booting from SPI-NAND. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mt76: add missing fileFelix Fietkau2021-04-111-2/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: update to the latest versionFelix Fietkau2021-04-111-3/+3
| | | | | | | | | | 028b7152b1a9 mt76: mt7921: remove 80+80 MHz support capabilities 7714dc914df6 mt76: report Rx timestamp ffd4cf15fa0e mt76: mt7915: add mmio.c fe8717dd573a mt76: mt7615: add missing SPDX tag in mmio.c 6b293c411d22 mt76: mt7615: always add rx header translation tlv when adding stations Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add client mode connection monitor fixFelix Fietkau2021-04-111-0/+31
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: support rx timestamps for HE ratesFelix Fietkau2021-04-111-0/+134
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mxs: add support for 5.10 as testing kernelZoltan HERPAI2021-04-112-0/+251
| | | | | | | | | | | | | | The 100-ARM-dts-imx23-introduce-mmc0_sck_cfg.patch does not need to be copied over as it's already merged upstream. Other notable change is the USB_CHIPIDEA_OF change to USB_CHIPIDEA_IMX [1]. [1] https://www.spinics.net/lists/linux-usb/msg193347.html Compile/runtime-tested on Olinuxino Micro (imx23). Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-08 11:06:18 +0000