aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for jjPlus JA76PF2Tomasz Maciej Nowak2019-03-186-4/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board. Specification SoC: Atheros AR7161 RAM: 64 MB DDR Flash: 16 MB SPI NOR Ethernet: 2x 10/100/1000 Mbps AR8316 LAN (CN11), WAN/PoE (CN6 - close to power barrel connector, 48 V) MiniPCI: 2x LEDS: 4x, which 3 are GPIO controlled Buttons: 2x GPIO controlled Reset (SW1, closer to ethernet ports), WPS (SW2) Serial: 1x (only RX and TX are wired) baud: 115200, parity: none, flow control: none Currently there is one caveat compared to ar71xx target images as the MAC addresses are random on every reboot. To remedy this one needs to store the WAN MAC address in RedBoot configuration. OpenWrt on first boot, after flashing, will read out the address and assign proper ones to both WAN and LAN ports. It is iportant to NOT keep the old configuration when doing sysupgrade from ar71xx. Upgrading from OpenWrt ar71xx image 1. Connect to serial port, 2. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n <openwrt_sysupgrade_image_name> 3. After writing new image OpenWrt will reboot, now interrupt boot process and enter RedBoot (bootloader) command line by pressing Ctrl+C, 4. Enter following commands (replace variable accordingly), set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_adress> (confirm storing the value by inputting y and pressing Enter) reset 5. Now board should restart and boot OpenWrt with proper MAC addresses. Installation 1. Prepare TFTP server with OpenWrt initramfs image, 2. Connect to WAN ethernet port, 3. Connect to serial port, 4. Power on the board and enter RedBoot (bootloader) command line by pressing Ctrl+C, 5. Enter following commands (replace variables accordingly): set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_address> (confirm storing the value by inputting y and pressing Enter) ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress> load -r -b 0x80060000 <openwrt_initramfs_image_name> exec -c "" 6. Now board should boot OpenWrt initramfs image, 7. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade <openwrt_sysupgrade_image_name> 8. Wait few minutes, after the D2 LED will stop blinking, the board is ready for configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: routerstation: prepare to use sysupgrade-tar format imageTomasz Maciej Nowak2019-03-182-5/+23
| | | | | | | | | | | | | | | | | | In PR [1] introducing initial support for Ubiquiti RouterStation boards, Mathias Kresin suggested to replace the combined sysupgrade image with tarball generated by sysupgrade-tar.sh. This would simplify deployment of sysupgrade as the kernel size (needed to update FIS partition) could be simply calculated on the fly instead of reading value from combined image header. Unfortunately this would break sysupgrade compatibility between ar71xx image and ath79 image. Therefore this commit creates migration path to use new sysuprade image, it adds code to accept both of them at this moment. The plan is to keep it until new stable version is released. Then the image recipe should be changed to new format and compatibility code for old image removed. 1. https://github.com/openwrt/openwrt/pull/1237 Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* lantiq: kernel 4.14: fix usb_phy1 reset status bit in vr9.dtsMartin Schiller2019-03-181-1/+1
| | | | | | The status of USB PHY 1 Reset Domain is also in bit 5 of RST_STAT2. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ath79: qca955x: add wmac migration hotplug eventTomasz Maciej Nowak2019-03-181-0/+32
| | | | | | | | | | | When upgrading from ar71xx target images to ath79 based ones, the integrated wireless interface changes its sysfs path. Therefore the previous enabled wireless interface will be disabled, which can cause false complains about it not working. This commit adds hotplug event which migrates to new path and will keep the wrireless interface enabled after upgrade. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: fix leds description for EnGenius EPG5000Tomasz Maciej Nowak2019-03-181-6/+6
| | | | | | | Align the LEDs deffinition with MACH file present in ar71xx target which has the correct LED functions and colors adescription. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* kernel: bump 4.14 to 4.14.106Koen Vandeputte2019-03-1812-26/+24
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.163Koen Vandeputte2019-03-182-3/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipset: size optimizationsDeng Qingfang2019-03-171-2/+5
| | | | | | | | | | | ipset utility was linked statically to libipset. Disable static library for dynamic linking to save space. Add -Wl,--gc-sections,--as-needed for further reduction MIPS ipk size: ipset: 29KiB -> 2KiB libipset: 39KiB -> 38KiB Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* Revert "tools/cmake: Update to 3.14.0"Stijn Tintel2019-03-175-8/+33
| | | | | | | | The cmake bump to 3.14.0 breaks build on all targets. Revert it for now. This reverts commit a3446257a8737bfc2899c5911791873561feecc7. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* tools/libelf: Add mirrors as main site is deadDaniel Engberg2019-03-171-2/+3
| | | | | | Main site hasn't resolved for days so just add a few mirrors instead Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/cmake: Update to 3.14.0Daniel Engberg2019-03-165-33/+8
| | | | | | | | | | Update CMake to 3.14.0 Refresh patches Remove inofficial fossies.org and replace with GitHub (link on official site) Remote 150-C-feature-checks-Match-warnings-more-strictly.patch as it's a no longer needed backport from upstream. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* mac80211: netifd: Use a mask when using `iw set antenna`Alexander Couzens2019-03-162-3/+6
| | | | | | | | The keyword "all" is only supported by `iw set antenna` if it's used as the only argument. Convert "all" into a mask before calling `iw set antenna`. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* mt76: update to the latest versionFelix Fietkau2019-03-161-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 00ac79d mt7603: fix initialization of max rx length 320af65 mt76: mt7603: use the correct hweight8() function bdee924 mt76: fix schedule while atomic in mt76x02_reset_state abcb544 mt76x02: do not enable RTS/CTS by default e97a209 mt76: remove mt76_queue dependency from tx_queue_skb function pointer ddd98f8 mt76: remove mt76_queue dependency from tx_prepare_skb function pointer 9bc2d56 mt76: remove mt76_queue dependency from tx_complete_skb function pointer 06c917f mt76: introduce mt76_sw_queue data structure 2dc63b0 mt76: introduce mt76_txq_id field in mt76_queue_entry 312f6fc mt76: remove irqsave/restore in locking for tx status fifo 0fe6386 mt76: move mt76x02_insert_hdr_pad in mt76-core module efe9a47 mt76: mmio: move mt76_insert_hdr_pad in mt76_dma_tx_queue_skb 0b03f87 mt76: move skb dma mapping before running tx_prepare_skb f977a92 mt76: introduce mt76_tx_info data structure 72fe286 mt76: use mac80211 txq scheduling b77b932 mt76: reduce locking in mt76_dma_tx_cleanup c0ab515 mt76: store wcid tx rate info in one u32 reduce locking f37ad72 mt76: mt76x02: store software PN/IV in wcid 5323005 mt76: move tx tasklet to struct mt76_dev 688d708 mt76: only schedule txqs from the tx tasklet 42ce040 mt76: use TX_NEEDS_ALIGNED4_SKBS 2660aa9 mt76: mt7603: store software PN/IV in wcid 3ce8a93 mt76: dma: add static qualifier to mt76_dma_tx_queue_skb 81a32aa mt7603: remove mt7603_mcu_init routine 48dc7e9 mt7603: core: do not use magic numbers in mt7603_reg_map 2236490 mt76: usb: reduce code indentation in mt76u_alloc_tx Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add a few performance improvement patchesFelix Fietkau2019-03-164-0/+297
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport flow dissector batman-adv supportFelix Fietkau2019-03-165-0/+2267
| | | | | | Improves performance on multicore systems handling batman-adv traffic Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: improve locking around the txq scheduling / airtime fairness APIFelix Fietkau2019-03-161-0/+214
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: backport the txq scheduling / airtime fairness APIFelix Fietkau2019-03-169-59/+1147
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix an unaligned access in the mesh hash table functionFelix Fietkau2019-03-161-0/+21
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: add support for suppressing the DHCP request hostname by setting it to *Felix Fietkau2019-03-161-0/+2
| | | | | | | | | dnsmasq (and probably other DHCP servers as well) does not like to hand out leases with duplicate host names. Adding support for skipping the hostname makes it easier to deploy setups where it is not guaranteed to be unique Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: update and fix the patch to allow 4-byte aligned tx skbsFelix Fietkau2019-03-1614-300/+371
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: allocate tailroom for forwarded mesh packetsFelix Fietkau2019-03-161-0/+37
| | | | | | Fixes a warning + packet loss on encrypted mesh networks with forwarding Signed-off-by: Felix Fietkau <nbd@nbd.name>
* iproute2: tc: reduce size of dynamic symbol tableTony Ambardar2019-03-142-1/+45
| | | | | | | | | | | | | In the case of SHARED_LIBS=y, don't use -export-dynamic to place *all* symbols into the dynamic symbol table. Instead, use --dynamic-list to export a smaller set of symbols similar to that defined in static-syms.h in the case of SHARED_LIBS=n, avoiding an 11 KB tc package size increase. The symbol set is based on that required by the only plugin, m_xt.so. Also increment PKG_RELEASE. Signed-off-by: Tony Ambardar <itugrok@yahoo.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE fixup]
* iproute2: tc: enable and fix support for using .so pluginsTony Ambardar2019-03-142-1/+107
| | | | | | | | | | | | | | | | | | | | | | | This enables using the tc module m_xt.so, which uses the act_ipt kernel module to allow tc actions based on iptables targets. e.g. tc filter add dev eth0 parent 1: prio 10 protocol ip \ u32 match u32 0 0 action xt -j DSCP --set-dscp-class BE Make the SHARED_LIBS parameter configurable and based on tc package selection. Fix a problem using the tc m_xt.so plugin as also described in https://bugs.debian.org/868059: Sync include/xtables.h from iptables to make sure the right offset is used when accessing structure members defined in libxtables. One could get “Extension does not know id …” otherwise. (See also: #868059) Patch to sync the included xtables.h with system iptables 1.6.x. This continues to work with iptables 1.8.2. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* iproute2: support eBFP/XDP object file loading, simplify linking libelfTony Ambardar2019-03-143-67/+30
| | | | | | | | | | | | | | Add build and runtime dependencies on libelf, allowing tc and ip-full to load BPF and XDP object files respectively. Define package 'tc' as a singleton package variant, which can be used to enable additional functionality limited only to tc. Also set ip-tiny as the default 'ip' variant. Preserve optionality of libelf by having configuration script follow the HAVE_ELF environment variable, used similarly to the HAVE_MNL variable. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* netifd: update to latest git HEAD (FS#2087)Hans Dedecker2019-03-141-3/+3
| | | | | | 81ac3bc interface-ip: fix delegate config update on reload (FS#2087) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* uboot-sunxi: add fix for A20-OLinuXino-Lime2-eMMC rev. K boardsZoltan HERPAI2019-03-131-0/+44
| | | | | | | The OLinuXino Lime2 rev. K boards use new PHYs (Micrel KSZ9031), so enable that. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: bump to 2019.01Zoltan HERPAI2019-03-135-9/+9
| | | | | | | | | | | | | | Tested on: Bananapro (A20) Banana Pi M3 (A83t) Linksprite pcDuino3 (A20) Olinuxino Lime (A10) Orange Pi 2 (H3) Pine64 (A64) Patches refreshed. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: ag71xx: Remove ndo_poll_controllerRosen Penev2019-03-131-17/+0
| | | | | | | | | | | | | | | | | | | | | | | | | It is unused by default and upstream is trying to remove it as it has negative effects when the driver is under load. Upstream explanation: netpoll: avoid capture effects for NAPI drivers As diagnosed by Song Liu, ndo_poll_controller() can be very dangerous on loaded hosts, since the cpu calling ndo_poll_controller() might steal all NAPI contexts (for all RX/TX queues of the NIC). This capture, showing one ksoftirqd eating all cycles can last for unlimited amount of time, since one cpu is generally not able to drain all the queues under load. It seems that all networking drivers that do use NAPI for their TX completions, should not provide a ndo_poll_controller() : Most NAPI drivers have netpoll support already handled in core networking stack, since netpoll_poll_dev( uses poll_napi(dev) to iterate through registered NAPI contexts for a device. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ar71xx: Speed up mtd extraction in ar71xx.shAdrian Schmutzler2019-03-131-2/+2
| | | | | | | | Although the amount of data read here is smaller than for the caldata, there still might be some speed gain compared to reading bytewise. And there is no harm ... Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Speed up caldata/eeprom handlingAdrian Schmutzler2019-03-132-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Speed comparison @ TP-Link TL-WDR4300 (just manually) results in a time reduction by three orders of magnitude (99.9 %). > time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096 4096+0 records in 4096+0 records out real 0m 15.85s user 0m 0.06s sys 0m 13.28s > time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.02s user 0m 0.00s sys 0m 0.02s Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Speed up caldata/eeprom handlingAdrian Schmutzler2019-03-132-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Speed comparison @ UBNT AC-Mesh (just manually) results in a time reduction by three orders of magnitude (99.9 %). > time dd if=/dev/mtd6 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096 4096+0 records in 4096+0 records out real 0m 16.84s user 0m 0.07s sys 0m 13.54s > time dd if=/dev/mtd6 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.02s user 0m 0.00s sys 0m 0.02s Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Rosen Penev <rosenp@gmail.com>
* apm821xx: usb: xhci: fix semicolon.cocci warningskbuild test robot2019-03-132-2/+2
| | | | | | | | | | | | drivers/usb/host/xhci-pci.c:788:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Fixes: 9e0fd1b52ad1 ("apm821xx: add support for the Netgear Centria N900 WNDR4700/WNDR4720") Signed-off-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [changed subject]
* gemini: Generate padded kernel+rootfs images for DIR-685Linus Walleij2019-03-135-3/+174
| | | | | | | | | | | | | | | | | | | | | We currently generate a kernel that boots from the harddrive in the DIR-685. That's not how we usually do things, so let's augment it to boot from flash and mount the rootfs using squashfs and JFFS2 like everyone else. Partition splitting only work when the partitions are inside of a "partitions" node which is why we have a patch like this (submitted upstream). Another patch drops the rootfs arguments and renames the firmware partition while adding the compatible "wrg" to it so the WRGG parser will kick in. Factory image was tested by bravely reflashing the DIR-685 from stock firmware using the web UI and the serial console boot loader. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* kernel: mtdsplit: wrgg: Support big and little endianLinus Walleij2019-03-131-0/+10
| | | | | | | | | | | | | | | | | | | The WRGG images exist in both big and little endian variants, as can be seen from the image generator in tools/firmware-utils/src/mkwrggimg.c, you either pass the "-b" flag or not. The D-Link DIR-685 is using little endian images so we need to support splitting these. Detect endianness like this: if the kernel entity size gets silly big (bigger than the flash memory) we are probably using the wrong endianness. Example: my kernel of 0x0067ff64 was switched around by wrong endianness and detected as 0x64ff67a0 (the actual size in swapped endianness + header 0xa0). Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add suport for EnGenius EPG5000Tomasz Maciej Nowak2019-03-135-12/+209
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band wireless router. Specification SoC: Qualcomm Atheros QCA9558 RAM: 256 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled Buttons: 2x GPIO controlled UART: 4 pin header, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Tools > Firmware, 4. Select OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Alternative installation 1. Prepare TFTP server with OpenWrt sysupgrade image, 2. Connect to one of LAN (yellow) ethernet ports, 3. Connect to UART port (leaving out VCC pin!), 4. Power on router, 5. When asked to enter a number 1 or 3 hit 2, this will select flashing image from TFTP server option, 6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8), then router ip (default is 192.168.99.9) and for last, image name downloaded from TFTP server (default is uImageESR1200_1750), 7. After providing all information U-Boot will start flashing the image, You can observe progress on console, it'll take few minutes and when the Power LED will stop blinking, router is ready for configuration. Additional information If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: aigo3d0a0tdagr useful for creating backup of original firmware. When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep the old configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ipq40xx: limit frequencies for Asus LyraMarius Genheimer2019-03-132-0/+4
| | | | | | | The Asus Lyra has filters in the antenna paths which limits the usable frequencies on both 5GHz radios. Signed-off-by: Marius Genheimer <mail@f0wl.cc>
* ipq40xx: add support for AVM FRITZ!Repeater 3000David Bauer2019-03-1311-6/+555
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M (NANYA NT5CC128M16JR-EK) FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI) ETH: Qualcomm QCA8072 WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac WiFi5: QCA9984 4T4R 4SS n/ac LED: - Connect green/blue/red - Power green BTN: WPS/Connect UART: 115200n8 3.3V VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz3000' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ3000.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz3000.bin uboot0 > mtd write /path/to/uboot-fritz3000.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* fritz-tools: add support for IPQ40xx platformDavid Bauer2019-03-133-5/+13
| | | | | | | | AVM devices based on Qualcomm IPQ40xx do not store sector health information in the OOB area. Make this check optional to support this platform. Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-fritz4040: bump version to 2019-03-03David Bauer2019-03-131-3/+3
| | | | | | Adds support for the AVM FRITZ!Repeater 3000 Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Add GL.iNet AR-300M-LiteJeff Kletsky2019-03-137-83/+91
| | | | | | | | | | | | | | | | | | | | | AR300M-Lite is single-Ethernet variant of the AR300M series Its eth0 would otherwise be assigned to the WAN interface making it unreachable firstboot or failsafe. Installation instructions from OEM (OpenWrt variant): * Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI), * Do not preserve settings * Access rebooted device via Ethernet at OpenWrt default address Add previously missing LED defaults for all three variants; -nand, -nor, -lite to the definitions in 01_leds Non-lite variants thanks to Andreas Ziegler https://patchwork.ozlabs.org/patch/1049396/ Runtime-tested: GL.iNet AR300M-Lite Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ramips: HC5861 drop unused gpio group define in dtsChen Minqiang2019-03-131-7/+0
| | | | Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add support for Xiaomi Mi Router 3 ProOzgur Can Leonard2019-03-136-2/+222
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: CPU: MediaTek MT7621AT (2x880MHz) RAM: 512MB DDR3 FLASH: 256MB NAND WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!) WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!) USB: 1x 3.0 ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000 LED: Power/Status BTN: RESET UART: 115200 8n1 Partition layout and boot: Stock Xiaomi firmware has the MTD split into (among others) - kernel0 (@0x200000) - kernel1 (@0x600000) - rootfs0 - rootfs1 - overlay (ubi) Xiaomi uboot expects to find kernels at 0x200000 & 0x600000 referred to as system 1 & system 2 respectively. a kernel is considered suitable for handing control over if its linux magic number exists & uImage CRC are correct. If either of those conditions fail, a matching sys'n'_fail flag is set in uboot env & a restart performed in the hope that the alternate kernel is okay. If neither kernel checksums ok and both are marked failed, system 2 is booted anyway. Note uboot's tftp flash install writes the transferred image to both kernel partitions. Installation: Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in kernel0 for ease of recovery, and install OpenWRT into kernel1 and after. The installation file for OpenWRT is a *squashfs-factory.bin file that contains the kernel and a ubi partition. This is flashed as follows: nvram set flag_try_sys1_failed=1 nvram set flag_try_sys2_failed=0 nvram commit dd if=factory.bin bs=1M count=4 | mtd write - kernel1 dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0 reboot Reverting to stock: The part of stock firmware we've kept in kernel0 allows us to run stock recovery, which will re-flash stock firmware from a *.bin file on a USB. For this we do the following: fw_setenv flag_try_sys1_failed 0 fw_setenv flag_try_sys2_failed 1 reboot After reboot the LED status light will blink red, at which point pressing the 'reset' button will cause stock firmware to be installed from USB. Issues: OpenWRT currently does not have support for the MT7615 wifi chips. There is ongoing work to add mt7615 support to the open source mt76 driver. Until that support is in place, there are closed-source kernel modules that can be used. See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170 Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [02_network remaps, Added link to notes]
* ath79: add support for LibreRouter v1Santiago Piccinini2019-03-135-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: QCA9558 RAM: 128M DDR2 Flash: 16MiB SPI-NOR ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through WiFi2: QCA9558 (bgn) 2T2R WiFi5: 2x mPCIE with AR9582 (an) 2T2R BTN: 1x Reset GPIO: multiple GPIO on header, PoE passthrough enable UART: 3.3V 115200 8N1 header on the board WDG: ATTiny13 watchdog JTAG: header on the board USB: 1x connector and 1x header on the board PoE: 10-32V input in ETH port 1, passthrough in port 2 mPCIE: 2x populated with radios (but replaceable) OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin using the web interface or with sysupgrade -n. Flash from bootloader (in case failsafe does not work) 1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART header in the board. 2. Connect an ETH cable and configure static ip addres 192.168.1.10/24 3. Turn on the device and stop the bootloader sending any key through the serial interface. 4. Use a TFTP server to serve <your image>-sysupgrade.bin file. 5. Execute the following commands at the bootloader prompt: ath> tftp 82000000 <your image>-sysupgrade.bin ath> erase 0x9f050000 +$filesize ath> cp.b 0x82000000 0x9f050000 $filesize ath> bootm 0x9f050000 More docs * Bootloader https://github.com/librerouterorg/u-boot * Board details (schematics, gerbers): https://github.com/librerouterorg/board Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
* ipq40xx: fix FRITZBox 7530 NAND controller nodeDavid Bauer2019-03-132-2/+0
| | | | | | | | This removes the 'cs-gpios' property from the AVM FRITZ!Box 7530 NAND controller node. As pointed out by Christian Lamparter, the property is not needed by the Qualcomm NAND controller driver. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix phy interrupt settingChristian Lamparter2019-03-132-2/+2
| | | | | | | | | | | | | This patch fixes a problem that was discovered during DSA development. On the MR33, the link change events from the external AR8035-PHY would never make it to the qca8k driver. The issue turned out to be a misplaced memcpy that was copying over the zero-initialized irq table, when it should have been set to PHY_POLL. Hence this patch moves the memcpy after the array has been initialized. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: tidy up 02_networksChristian Lamparter2019-03-131-2/+2
| | | | | | | | - fix linksys' EA6350v3 order - remove whitespace that should have been tabs Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* openssl: disable digests by default, misc fixesEneas U de Queiroz2019-03-124-2/+79
| | | | | | | | | | | | | | | | | | | | | | Openssh uses digest contexts across forks, which is not supported by the /dev/crypto engine. The speed of digests is usually not worth enabling them anyway. This changes the default of the DIGESTS option to NONE, so the user still has the option to enable them. Added another patch related to the use of encryption contexts across forks, that ignores a failure to close a previous open session when reinitializing a context, instead of failing the reinitialization. Added a link to the Cryptographic Hardware Accelerators document to the engine pacakges description, to provide more detailed instructions to configure the engines. Revert the removal of the OPENSSL_ENGINE_CRYPTO symbol, currently used by openssh. There is an open PR to update openssh; when merged, this symbol can be safely removed. Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [refresh patches]
* oxnas: install wireless driver on pogoplugproDaniel Golle2019-03-121-1/+1
| | | | | | | | PogoPlug Pro comes with AzureWave AW-NE762H PCIe module containing Ralink's Rt3090 chip supported by the rt2x00 driver. Install the driver as well as wpad-basic. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: rt2x00: import and update pending patchesDaniel Golle2019-03-1212-5/+192
| | | | | | | | | | | Imported from patchwork, patches marked with '=' have already been in our tree: [v3,1/4] cfg80211: add ratelimited variants of err and warn [v3,2/4] rt2x00: use ratelimited variants dev_warn/dev_err [v3,3/4] rt2x00: check number of EPROTO errors =[v3,4/4] rt2x00: do not print error when queue is full Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: also akitio,mycloud uses PCIe apparentlyDaniel Golle2019-03-121-0/+4
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 05:30:20 +0000