| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The
device was previously supported on the now removed ar71xx target.
SoC Atheros AR9344
WiFi Atheros AR9344 & Atheros AR9280
ETH Atheros AR8327
RAM 128M DDR2
FLASH 16M SPI-NOR
Installation
------------
Follow the Ubiquiti TFTP recovery procedure for this device.
1. Hold down the reset button while connecting power for 10 seconds.
2. Transfer the factory image via TFTP to the AP (192.168.1.20)
3. Wait 2 minutes for the AP to write the firmware to flash. The device
will automatically reboot to OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
Apply alphabetic sorting like in the other files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
There is no apparent reason to have an empty default case.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
Apply alphabetic sorting like in the other files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On devices with small amounts of RAM, zram-swap fails to initialise due to the
default compression algorithm (lzo-rle). Startup example on an AirGrid M2, with
32 MiB of RAM:
root@airgrid:/etc/config# /etc/init.d/zram start
zram_start: activating '/dev/zram0' for swapping (13 MegaBytes)
zram_reset: enforcing defaults via /sys/block/zram0/reset
sh: write error: Out of memory
mkswap: image is too small
swapon: /dev/zram0: Invalid argument
root@airgrid:/etc/config#
Fix this by defaulting to traditional lzo, which works fine and is always
available.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Edgecore ECW5211 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Edgecore ECW5410 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.
Installation instructions:
Through stock firmware or initramfs.
1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>
This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0
Note
Initramfs:
1. Connect to console
2. Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1
You need to interrupt the bootloader after rebooting and run:
run altbootcmd
This will switch your active rootfs partition to one you wrote to and boot from it.
So if rootfs1 is active, then it will change it to rootfs2.
This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.
5. Transfer sysupgrade image
6. Flash with sysupgrade -n.
Note that sysupgrade will write the image to rootfs partition that is not currently in use.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This imports the patch that adds bootargs-append support from IPQ40xx.
This way we can append additional boot arguments from DTS instead of only being able to overwrite them.
This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot.
But we still need to append console info and ubi root info.
This is used by Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
|
|
|
|
|
|
| |
IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it.
Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
|
|
|
|
|
| |
Its needed for Edgecore ECW5410 which does not use QCA8337 switch,
but rather 2x AR8033 PHY-s directly connected to GMAC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
|
|
|
|
|
|
|
| |
This enables the ipq-wifi package to be used on IPQ806x target.
Its needed for boards using a different BDF than one shipped in the upstream board-2.bin.
Currently needed for Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
|
|
|
|
| |
Remove trailing whitespaces in dts files.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
|
|
|
|
|
|
| |
Improves tx throughput when connecting to some APs (e.g. Asus RT-AC88U)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
| |
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.
Fixes: 480bf2827392 ("ath79: add support for Buffalo WZR-HP-AG300H")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The hardware of this device seems to be identical to WZR-HP-AG300H.
It was already implemented as a clone in ar71xx.
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM
- 32 MiB Flash
- WiFi 5 GHz a/n
- WiFi 2.4 GHz b/g/n
- 5x 1000Base-T Ethernet
- 1x USB 2.0
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
The Buffalo devices in ath79 share their image generation code,
so let's create a shared Device definition for them.
Since most of them use BUFFALO_HWVER := 3, this is moved as
default to the shared definition as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
vconfig has been disabled by default since 2015 [1] and there are
no remaining uses in entire OpenWrt trunk. However, we still set up
a specific name_type for it during boot.
While this setup is properly implemented to be only triggered when
vconfig is present, it still seems anachronistic and unnecessary
to set up a standard for a tool that is not used anymore.
Therefore, this removes the set_name_type initialization and leaves
it for those people actually using the tool to configure it as needed.
[1] 899a23227e55 ("busybox: improve applets & deprecate ifconfig, route")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Assign return value of kstrtoul to error variable instead of
conversion value.
Suggested-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
Use "make kernel_oldconfig" to update and sort target config.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
Seems like leftovers from development, remove them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
1172357 ubus: add new RESTful API
fe1888f ubus: fix blob_buf initialization
Fixes: 3d167ed805a9 ("uhttpd: update to the latest master")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
| |
Do some minor empty lines cleanup, i.e. remove those at EOF and
add some for cosmetic reasons/consistency.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit 34cc2c9a99f6542f009aa660790061f169aa96b3.
The reverted shell code is a very poor reimplementation of the existing
package-metadata.pl usergroup subcommand and the resulting file is not
used anymore, so drop this code.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
| |
Use the prepared .packageusergroup file to lookup user and group names
when processing the passed file mode.
Also replace the various subshell/cut invocations with a sequence of
standard variable interpolations which fixes paths with embedded colons
as a side-effect.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
| |
This file can be subsequently used to resolve symbolic user or group names
to their numeric IDs when packing ipk archives.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
| |
With the introduction of `./tmp/userids` the `ipkg-build` script can now
resolve values of "PKG_FILE_MODES", allowing users to set names rather
than numeric values.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Multiple packages contain a USERID variable defining required user and
group for the package to run. With the recent addition of
"PKG_FILE_MODES" it is possible to define user and group of specific
files, replacing (possibly insecure) post-inst scripts. These modes are
set during build time and put directly into the packages.
To allow user and group names rather than the numeric values, a mapping
like `/etc/passwd` is required by the `ipkg-build` script, mapping names
defined in "PKG_FILE_MODES" to a numeric value, as the build system does
not create any users during build.
This commit adds a single line to the `prepare-tmpinfo` target, so that
everytime the feeds are updated the *passwd like* content of
`./tmp/userids` is updated.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the RTL838x Architecture.
SoCs of this type are used in managed and un-managed Switches and Routers
with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash,
Ethernet including a DSA switch driver and internal and external PHYs used
with these switches.
Supported SoCs:
RTL8380M
RTL8381M
RTL8382M
The kernel will also boot on the following RTL839x SoCs, however driver
support apart from spi-nor is missing:
RTL8390
RTL8391
RTL8393
The following PHYs are supported:
RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port)
RTL8218B internal: internal PHY of the RTL838x chips
RTL8318b external (QSGMII 8-port GMAC phy)
RTL8382M SerDes for 2 SFP ports
Initialization sequences for the PHYs are provided in the form of
firmware files.
Flash driver supports 3 / 4 byte access
DSA switch driver supports VLANs, port isolation, STP and port mirroring.
The ALLNET ALL-SG8208M is supported as Proof of Concept:
RTL8382M SoC
1 MIPS 4KEc core @ 500MHz
8 Internal PHYs (RTL8218B)
128MB DRAM (Nanya NT5TU128MB)
16MB NOR Flash (MXIC 25L128)
8 GBEthernet ports with one green status LED each (SoC controlled)
1 Power LED (not configurable)
1 SYS LED (configurable)
1 On-Off switch (not configurable)
1 Reset button at the right behind right air-vent (not configurable)
1 Reset button on front panel (configurable)
12V 1A barrel connector
1 serial header with populated standard pin connector and with markings
GND TX RX Vcc(3.3V), connection properties: 115200 8N1
To install, upload the sysupgrade image to the OEM webpage.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
| |
Add support for uimage headers from ALLNET and provide support for the
SG8208M and SG8310PM devices' magic bytes.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This target has not been updated to 5.4 yet, and the only person
trying it (Koen) decided to retreat based on the following reasons:
- The target is not DT-aware at all
- The huge amount of effort required
- The SoC itself reached EoL at Cavium for some time now
- Upstream removed some important parts as it's also slowly getting EoL
over there
- The commercial product that used this will fade out shortly
- The amount of download for this binary suggest that the target is not
that popular
Since nobody has picked up the work since then, and this is the last
remaining 4.19-only target, finally drop it now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead
of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2
(May 10, 2019).
Check the installed u-boot release, and set the default accordingly.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
[bump PKG_RELEASE, use lower case for hex offset]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This board is equipped with Winbond W25Q256FV 32M SPI-NOR.
Fix partition size for that.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
| |
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
|
| |
this board has a pcie to sata bridge connected to pcie2 with a
separated pcie reset on gpio7.
add reset-gpios and corresponding pinctrl nodes into dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
|
|
| |
Backport upstream changes to initialize GDM settings and reset PPE
Allow GMAC to recognize the special tag to fix PPE packet parsing
Improve GRO performance by passing PPE L4 hash as skb hash
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
| |
All modifications made by update_kernel.sh/no manual intervention needed
Build-tested: x86_64
Run-tested: ipq806x (R7800)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
| |
55a7b6b netifd: vxlan: add aging and maxaddress options
11223f5 netifd: vxlan: add most missing boolean options
226566b netifd: vxlan: refactor mapping of boolean attrs
a3c033e netifd: vxlan: handle srcport range
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Mercury MW4530R is a TP-Link TL-WDR4310 clone.
Specification:
* SOC: Atheros AR9344 (560 MHz)
* RAM: 128 MiB
* Flash: 8192 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
Installation:
Flash factory image via OEM web interface.
Signed-off-by: Zhong Jianxin <azuwis@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove upstreamed patches:
generic-backport
701-v5.5-net-core-use-listified-Rx-for-GRO_NORMAL-in-napi_gro.patch
Manually merged:
mediatek/patches-5.4
0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch
All other modifications made by update_kernel.sh
Build-tested: ipq806x, lantiq/xrx200, mvebu, x86/64
Run-tested: ipq806x (R7800), mvebu (mamba, rango),
lantiq/xrx200 (Easybox 904 xDSL), x86/64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add community build/run tests to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
HooToo HT-TM05 and RAVPower RP-WD03 have almost identical hardware
(except for RAM size) and are from the same vendor (SunValley).
Create a common DTSI file for them.
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
The baud rate for the RAVPower RP-WD03 is 57600, not 115200.
Since this is the default from mt7620n.dtsi, the chosen node can
simply be removed from the device DTS.
Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
According to the User Manual, there is a "Wi-Fi LED" with blue and
green colors, doing the following by default:
Flashing Blue: System loading
Solid Blue: System loaded
Flashing Green: Connecting to the Internet
Solid Green: Connected to the Internet
According to this vendor behavior, we keep refer to the LED as "wifi"
but implement the according default behavior as in OEM firmware.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
The previously used location 0x4000 for ethernet is actually empty.
Therefore, fix the ethernet MAC address and set it as label-mac-address.
Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
The proper model name is RP-WD03 (i.e. with the RP- prefix).
Adjust all names to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
The patch is only included in kernel 5.5.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|