| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
| |
eth_hw_addr_random additionally sets addr_assign_type to NET_ADDR_RANDOM.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is based on the EX6150v2, which should be identical to
the EX6100v2:
The device bears two MAC addresses ("MAC 1" and "MAC 2") that
correspond to phy0 and phy1.
The ethernet MAC address (gmac0) is the same as phy0.
As this one is accessible via local-mac-address in gmac0, the
latter is used for label-mac-device.
(Although this is a one-port, gmac1 also has a local-mac-address
assigned. This has the same vendor part as the other addresses,
but completely different data for the device part.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
If flash size is used as part of a device's title, it should be
specified as DEVICE_VARIANT like for the other devices so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
This fixes the remaining IMAGE_SIZE issues in ath79 target.
All devices in target have been checked, so together with
previous patches this target should be "clean" afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
So far, IMAGE_SIZE is set as follows:
tplink-4m* 3904k 0x3d0000
tplink-8m* 7936k 0x7c0000
tplink-16m* 15872k 0xf80000
However, based on the size of firmware partitions in DTS it should
be:
tplink-4m* 3904k 0x3d0000
tplink-8m* 8000k 0x7d0000
tplink-16m* 16192k 0xfd0000
All (!) 8m*/16m* devices actually follow the latter scheme, which
is also consistent in terms of left free space for other
partitions. Thus, fix it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by:
1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"),
since despite two all subdefinition have different values.
2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k).
3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node
since all have same size (it is defined in parent DTSI ...).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Factory image generated for Netgear WNR1000 v2 has incorrect device
and hardware ID information in header due to missing makefile
variables. This fix adds them to device section.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Attention: Kernel partition size has been enlarged to 4MB.
To switch, you must update to latest ar71xx-nand snapshort and flash the
sysupgrade-4M-Kernel.bin:
zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f
You will end up with a fresh config if you do not inject config into the image.
The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but
ath79 can only use the first 128MB. Therefore the complete NAND needs to be
overwritten. If not, the old UBI may make problems and lead to reboot loop.
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6716> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6716>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6716> ATSE NBG6716
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6716> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6716> ATGU
|NBG6716#
Signed-off-by: André Valentin <avalentin@marcant.net>
|
|
|
|
|
|
|
| |
-Fix the kernel image generation (more robust)
-Add a firmware partition table allowing easy upgrade to ath79
Signed-off-by: André Valentin <avalentin@marcant.net>
|
|
|
|
|
|
| |
128k header size support is needed for ZyXEL NBG6716.
Signed-off-by: André Valentin <avalentin@marcant.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- CMIIT ID: 2019AP2581
- SoC: MediaTek MT7621
- Flash: 16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM: 128MiB DDR3 (ESMT M15T1G1664A)
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
INSTALLATION:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.
With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.
For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).
Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".
[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
|
|
|
|
|
|
| |
request_irq requires irq names to be static/allocated and not on the stack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch removes a phy0tpt trigger from the power LED, which
seems to have been added by mistake.
WiFi LEDs using phy0radio and phy1radio triggers are present and
used correctly.
Cc: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
In mt7628an.dtsi, calibration data for wmac is already defined:
mediatek,mtd-eeprom = <&factory 0x0>;
Thus, this patch removes redundant entries of this property in
derived DTS files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
When caldata locations are defined with mediatek,mtd-eeprom the
MAC address is automatically read from offset +4. Thus, specifying
that location explicitly is redundant.
This patch removes those redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
generic: Add/rename patches for upstream consistency
ipq40xx: generic-level patch replaces same-source patches-4.19/
082-v4.20-mtd-spinand-winbond-Add-support-for-W25N01GV.patch
The SPI-NAND framework from Linux uses common driver code that is then
"tuned" by a tiny struct of chip-specific data that describes
available commands, timing, and layout (data and OOB data). Several
manufacturers and chips have been added since 4.19, several of which
are used in devices already supported by OpenWrt (typically with no or
"legacy" access to their NAND memory). This commit catches up the
supported-chip definitions through Linux 5.2-rc6 and linux/next.
The driver is only compiled for platforms with CONFIG_MTD_SPI_NAND=y.
This presently includes ipq40xx and pistachio, with the addition of
ath79-nand in these commits (and not ath79-generic or ath79-tiny).
Upstream patches refreshed against 4.19.75
Build-tested-on: ipq40xx
Run-tested-on: ath79-nand
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
| |
Add the GL.iNet GL-AR300M-Lite to the list of supported boards.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
| |
Rework DEVICE_VENDOR, DEVICE_MODEL, and DEVICE_VARIANT
for the GL-AR300M series on the ath79-generic target.
Changes GL-AR300M-Lite to the current form with
DEVICE_VARIANT := Lite (board name is unchanged)
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The GL-AR750S has an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.2 ms period, ~89 kHz
The board has well-labeled (unpopulated) headers for serial and I2C
along the front edge of the board (the edge with the LEDs). Looking
from the top, rear of the unit (behind Ethernet jacks)
-------------------------------------------
5G_LED 2G_LED PWR_LED
O O O O O O O
3 S S G T R G
V C D N X X N
3 L A D D
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The GL-AR300M series have an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.4 ms period, ~88 kHz
The board has two sets of (unpopulated) headers. While facing the
back of the board (looking into the Ethernet jacks), and looking from
the top, the one on the left edge of the baord with four holes is the
I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards.
| (Patch antenna)
|
|
| O GND
| O SDA / GPIO 17
| O SCL / GPIO 16
| ⊡ 3V3 (square land)
|
| (Ethernet jacks)
https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states
"Note: I2C is not working in some early version of the router."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.
On both routers the installation can be done also via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Changelog:
v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release
Signed-off-by: Gabor Varga <vargagab@gmail.com>
|
|
|
|
|
|
| |
Less chance of missing out kconfig symbols at least
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
| |
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
| |
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Hardware
--------
SoC: Qualcomm IPQ4019
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: 2T2R IPQ4019 bgn
2T2R IPQ4019 a/n/ac
ETH: Atheros AR8033 RGMII PHY
BTN: 1x Connect (WPS)
LED: Power (green/red/yellow)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz1200'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ1200.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz1200.bin uboot0
> mtd write /path/to/uboot-fritz1200.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
| |
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
| |
f92be9d add support for AVM FRITZ!Repeater 1200
d651302 enable support for Atheros AR8033 PHY
e4c857c add machtype override hack
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
| |
This adds a missing backslash in the caldata-extraction script. Without
this fix, caldata extraction fails for every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
| |
This commit completely fixes the abortion of the ipq40xx ethernet driver
probe in case no phy-reset is defined.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
| |
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
|
|
|
|
|
|
| |
258aa04 procd: Add cached and available to memory table
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes the following build error when building when using GCC 8.3:
In file included from ./include/linux/string.h:19,
from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./arch/mips/include/asm/processor.h:15,
from ./arch/mips/include/asm/thread_info.h:16,
from ./include/linux/thread_info.h:38,
from ./include/asm-generic/preempt.h:5,
from ./arch/mips/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:81,
from ./include/linux/spinlock.h:51,
from ./include/linux/mmzone.h:8,
from ./include/linux/bootmem.h:8,
from arch/mips/bcm63xx/prom.c:10:
arch/mips/bcm63xx/prom.c: In function 'prom_init':
./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds]
__ret = __builtin_memcpy((dst), (src), __len); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy'
memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
^~~~~~
In file included from arch/mips/bcm63xx/prom.c:14:
./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here
extern char bmips_smp_movevec;
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
This commit fixes failing builds because of an incorrect configuration
for the kmod-rtw88 package.
RTW88_8822BE as well as RTW88_8822CE have to bes selected as "y" even
when building the driver as a module.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Based on stock firmware tests, both LAN and WAN ports use the
MAC address from 0x28 on factory partition.
In OpenWrt, this one is already set in DTS. This patch removes the
local bit set in 02_network previously, and adjusts LAN/WAN
addresses as on stock firmware.
Note that in tests we found a MAC address in 0x2e that is the one
in 0x28 plus 1. Since stock firmware does not use it though, we
do not use it either.
Thanks to Chih-Wei Chen for testing this on his device.
ref: https://github.com/openwrt/openwrt/pull/2497
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
| |
Moving a file between tmpfs and other fs is neither
faster nor safer, thus no point in doing it in two steps.
Use new jshn option to write output directly to file.
Originally discussed here:
http://lists.openwrt.org/pipermail/openwrt-devel/2017-December/010127.html
Signed-off-by: Roman Yeryomin <roman@advem.lv>
|
|
|
|
|
|
| |
eb30a03 libubox, jshn: add option to write output to a file
Signed-off-by: Roman Yeryomin <roman@advem.lv>
|
|
|
|
|
|
|
| |
This commit adds packages for the Realtek RTl8822BE/RTL8822CE firmware
to be used with the rtw88 driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
| |
This commits adds packaging for the new RTW88 driver from Realtek.
It supports the Realtek 8822BE/8822CE PCIe wireless chips.
For operation, the complementary firmware has to be loaded.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
| |
If a gpio reset pin was not defined we should not bog out.
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
| |
* 40f939d57c67 Tag version 1.0.1
* 9e758e6e6aec jitterentropy-rngd: update to version v1.1.0 + clang compile fix
* 193586a25adc Fix wrong types in format strings used in debug build
* d474977bb611 Add initial GitLab CI support
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
| |
Device node names were updated, but updating TARGET_DEVICES
was overlooked.
Fixes: 4408723d42e0 ("ramips: remove RAM size from device name
for UniElec devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
This reverts commit 4a45e69d190f72ed94878487b271ed7651dd9efa.
This broke the buildbots
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
|
| |
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.
Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
Previous commit 0cc87b3 "ath79: image: disable sysupgrade images for
routerstations and ja76pf2" doesn't remedy completely the posibility of
bricking the device, since user could try to downgrade with an older
image. Therefore disable sysupgrade code for these boards with a small
note.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
|
|
|
|
| |
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
This removes a useless empty default case.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This converts leading whitespaces to tabs and removes a double
newline at the end of the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
| |
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
While at it, add/remove newlines in keys and leds node where
necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|