aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* build: drop ABI version from metadataFelix Fietkau2021-02-145-21/+9
| | | | | | | Preparation for supporting dynamic ABI versions that depend on the runtime configuration. Read the suffix from the staging dir pkginfo version files. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: use PKG_ABI_VERSIONFelix Fietkau2021-02-141-1/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: add support for fixing up library sonameFelix Fietkau2021-02-144-0/+86
| | | | | | | | | | This makes it possible to declare a package ABI_VERSION independent from the upstream soname by setting PKG_ABI_VERSION in the package makefile. The library filename is fixed up for files installed to packages and to the staging dir. References to the original from executables within the same package are also fixed up Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: fix ABI version rebuild dependencyFelix Fietkau2021-02-141-1/+1
| | | | | | | A stray comma was being appended to the last package version dependency, causing it to be missed for ABI version checks Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix a regression in processing rx statsFelix Fietkau2021-02-141-0/+28
| | | | | | | A logic error caused rx rate update to be missed for any driver not using fast-rx Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: refresh patchesFelix Fietkau2021-02-1412-102/+92
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add minstrel performance improvementsFelix Fietkau2021-02-142-0/+181
| | | | | | Reduce fluctuations in rate selection / statistics Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add decapsulation offload supportFelix Fietkau2021-02-143-2/+593
| | | | | | | On hardware that supports this, this will improve performance by passing 802.3 frames from the hardware to the stack Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix a corner case in encapsulation offload supportFelix Fietkau2021-02-141-0/+53
| | | | | | Fix encryption key selection with WEP Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add fq performace improvementsFelix Fietkau2021-02-144-1/+554
| | | | | | Improves performance under load Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libnftnl: update to 1.1.8Rosen Penev2021-02-141-7/+8
| | | | | | | | | | | | | | Fix license information. Fix wrong ABI version. The library is versioned as libnftnl.so.11.4.0 Add PKG_BUILD_PARALLEL for faster compilation. Remove autoreconf as nothing is being patched. Minor cleanups for consistency between packages. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* libevent2: update to 2.1.12Rosen Penev2021-02-143-73/+3
| | | | | | Remove upstream backports. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* readline: update to 8.1Rosen Penev2021-02-141-3/+3
| | | | | | Fix license. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* gmp: update to 6.2.1Rosen Penev2021-02-141-4/+4
| | | | | | Fix license information. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* f2fs-tools: update to 1.14.0Rosen Penev2021-02-141-6/+6
| | | | | | Fix license information. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* COPYING: add COPYING file to specify project licensesAdrian Schmutzler2021-02-141-0/+12
| | | | | | | | Since multiple licenses are provided now in the LICENSES folder, add a COPYING file to specify the project license. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* scripts: fix checkpatch.pl for changed license dirPaul Spooren2021-02-141-1/+1
| | | | | | | As multiple LICENSES are shipped and no longer just LICENSE, modify the OpenWrt tree detection in checkpatch.pl. Signed-off-by: Paul Spooren <mail@aparcar.org>
* LICENSES: include all used licenses in LICENSES directoryAdrian Schmutzler2021-02-147-20/+444
| | | | | | | | | | | | | | | | OpenWrt ships code not only licensed via GPL-2.0-{only,or-later}. Reflect that by adding the missing licenses, just like the kernel does. This patch takes the license text as it is found in the Linux kernel, which might probably be the best common denominator here. In contrast to the kernel versions, only some changes to the valid and recommended identifiers were made (GPL-x.x+ vs. GPL-x.x-or-later and similar). Suggested-by: Paul Spooren <mail@aparcar.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.98John Audia2021-02-141-2/+2
| | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. No manual changes needed. Build system: x86_64 Build-tested: bcm27xx/bcm2711, ipq806x/R7800 Run-tested: ipq806x/R7800 Compile-tested [*]: ath79/{generic,tiny}, ipq40xx, octeon, realtek, ramips/{mt7620,mt7621}, x86/64 Run-tested [*]: ath79/{generic,tiny}: WNDR3700v2 / TL-WR841N v7 octeon: EdgeRouter Lite ramips/{mt7620,mt7621}: Archer C2 v1 / DIR-878 A1, EAP235-Wall, R6800, RT-AC57U v1 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* ath79: fix factory image generation for Netgear and Zyxel boardsPaul Fertser2021-02-143-4/+2
| | | | | | | | | | | | | The factory images need to embed specific IDs to pass verification with the OEM firmware (including TFTP recovery), so they need to be per-device variables. Fixes: ab1584a797ad ("ath79: netgear: trim down uImage customisations") Fixes: 459c8c9ef816 ("ath79: add support for ZyXEL NBG6616") Reported-by: Marcin Juszkiewicz <marcin-openwrt@juszkiewicz.com.pl> Signed-off-by: Paul Fertser <fercerpav@gmail.com> [minor commit message adjustments, sort DEVICE_VARS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* busybox: remove useless busybox patchesRosen Penev2021-02-143-26/+0
| | | | | | | | | The first two are useless as /bin/sh can execute those scripts just fine. Shellcheck reports no problems. Telnetd patch is useless as telnet is no longer used in OpenWrt. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* busybox: update to 1.33Rosen Penev2021-02-1431-429/+255
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove stime backport. Remove static libgcc patch as upstream fixed it with BUSYBOX_DEFAULT_STATIC_LIBGCC which defauls to off. Remove date -k patch as it no longer applies. It's also pointless as busybox' hwclock utility can do the same thing. Remove ntpd patch as that seems to have been applied upstream. Add smalll patch fixing compilation with SELinux. Upstream commit 2496616b0a8d1c80cd1416b73a4847b59b9f969a renamed the variable without renaming it in the SELinux path. Refresh config and patches. Config refresh: Refresh commands, run after busybox is first built once: cd package/utils/busybox/config/ ../convert_menuconfig.pl ../../../../build_dir/target-mips_24kc_musl/busybox-default/busybox-1.33.0 cd .. ./convert_defaults.pl < ../../../build_dir/target-mips_24kc_musl/busybox-default/busybox-1.33.0/.config > Config-defaults.in Manual edits needed afterward: * Config-defaults.in: OpenWrt config symbol IPV6 logic applied to BUSYBOX_DEFAULT_FEATURE_IPV6 * Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec) * editors/Config.in: Add USE_GLIBC dependency to BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090) * shell/Config.in : change at "Options common to all shells" the symbol SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH (discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html Apparently our script does not see the hidden option while prepending config options with "BUSYBOX_CONFIG_" which leads to a missed dependency when the options are later evaluated.) * Edit Config.in files by adding quotes to sourced items in config/Config.in, networking/Config.in and util-linux/Config.in (commit 1da014f) Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> [Added comments from Hannu Nyman to commit message] Signed-off-by: Rosen Penev <rosenp@gmail.com>
* base-files: use hwclock --systzRosen Penev2021-02-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | The date -k patch is non standard and will be removed in the next commit. Tested behavior to be identical with a simple C program: #define _GNU_SOURCE #include <unistd.h> #include <stdio.h> #include <sys/time.h> #include <sys/syscall.h> int main() { struct timezone tt; struct timezone tz; int a = syscall(SYS_gettimeofday, NULL, &tt); int b = gettimeofday(NULL, &tz); printf("%d - %d, %d\n", a, tt.tz_minuteswest, tt.tz_dsttime); printf("%d - %d, %d\n", b, tz.tz_minuteswest, tz.tz_dsttime); } Signed-off-by: Rosen Penev <rosenp@gmail.com>
* iw: Update to version 5.9Hauke Mehrtens2021-02-143-354/+12
| | | | | | | The nl80211.h file is mostly matching kernel 5.10, so remove most of our changes from the patch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.10-rc6-1Hauke Mehrtens2021-02-1456-3215/+555
| | | | | | | | | The removed patches were applied upstream. This adapts ath10k-ct and mt76 to changed APIs. nl80211.h in iw is updated to match the version from backports. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.9.12-1Hauke Mehrtens2021-02-1453-1450/+177
| | | | | | | | | | | The removed patches were applied upstream. Remove the 300-mac80211-optimize-skb-resizing.patch. This patch was not applied upstream, but it conflicts with upstream changes and needs bigger changes. It was applied with Felix to remove this patch for now. It should be reworked and then send upstream later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: espressobin: drop COMPHY removement patchTomasz Maciej Nowak2021-02-142-53/+0
| | | | | | | | | | There are proper workarounds merged to 5.4 stable tree for ESPRESSObin boards with older bootloader: 4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720") 40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ramips: manage low reset linesSander Vanheule2021-02-141-0/+47
| | | | | | | | | | | | The bootloader of a number of recent TP-Link devices does not properly initialise the MT7621's internal switch when booting from flash. To enable the mt7530 driver to clear the reset on the switch, the ramips reset controller must be allowed to toggle these. Backport upstream commit 3f9ef7785a9c from mips-next to allow control of the "mcm" reset line. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* imx6: bootscript-apalis: make it working on v2021.01 releasePetr Štetiar2021-02-141-2/+4
| | | | | | | | | Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration updates") removed emmc legacy wrappers, but so far didn't included any replacements. Fix it by simply defining the missing variables and UUID gathering directly into the boot script. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* uboot-imx6: bump to 2021.01 releasePetr Štetiar2021-02-143-24/+11
| | | | | | | | | | | | | | | Refreshed all patches, removed 110-mx6cuboxi-mmc-fallback.patch as it seems, that upstream has probably added similar funcionality in commit 6c3fbf3e456c ("mx6cuboxi: customize board_boot_order to access eMMC") and it needs to be re-verified by device owner. Run tested on apalis. Cc: Felix Fietkau <nbd@nbd.name> Cc: Vladimir Vid <vladimir.vid@sartura.hr> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* bcm4908: refresh patchesAdrian Schmutzler2021-02-132-503/+1534
| | | | | | | | | | Our patch refresh tool creates quite a big diff for these patches, as it does not use rename syntax. Push the refresh separately so it does not pollute the next kernel bump. This is a purely cosmetic change. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix chip used for Meraki MR12 caldata_extractMartin Kennedy2021-02-131-3/+3
| | | | | | | | | | | | | The original setup fails to trigger ART calibration data extraction for the AR9287. Instead, it would only have extracted calibration data for an internal WMAC chip which is not present on this board. Fixes: 55d2db0e8ceb ("ath79: add support for Meraki MR12") Signed-off-by: Martin Kennedy <hurricos@gmail.com> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove factory image for TP-Link Archer C2 v1Stijn Segers2021-02-131-0/+1
| | | | | | | | | | | | | | | | | | | Initial commit 8375623a0640 ("ramips: add support for TP-Link Archer C2") contains detailed installation instructions, which do not mention a factory image. From what I can see, no support to install OpenWrt through the vendor web interface has been added since. The factory image is also conspicuously absent from the device page in the wiki. Yet, it is available for download. I bricked my Archer C2 loading the factory image through the web UI. Serial showed this error during bootloop: Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover This patch disables the undocumented factory image so users won't get tricked into thinking easy web UI flashing actually works. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* trusted-firmware-a: fix project name spellingDaniel Golle2021-02-131-1/+1
| | | | | | | The version string generated for ARM Trusted-Firmware-A was stated as "OpenWRT". Fix that by changing it to the exact spelling "OpenWrt" Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* iwinfo: update to version 2021-01-31Daniel Golle2021-02-131-3/+3
| | | | | | | 5a2dd18 iwinfo: add hardware description for MediaTek MT7622 4a32b33 iwinfo: add PCI ID for MediaTek MT7613BE Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: add patch for setting 4addr mode in multi_apRaphaël Mélotte2021-02-137-47/+57
| | | | | | | | | This patch is required to be able to roam from one backhaul AP to another one in the same ESS. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (daniel@makrotopia.org: PKG_REVISION bump and refreshed patches) Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
* glibc: update to latest 2.33 commitHans Dedecker2021-02-131-2/+2
| | | | | | | | c5e3545897 tunables: Disallow negative values for some tunables 905fdc7071 x86: Use SIZE_MAX instead of (long int)-1 for tunable range value 15afd6b8d8 tunables: Simplify TUNABLE_SET interface Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* bcm4908: fix handling Ethernet frames of size 1506 - 1514Rafał Miłecki2021-02-121-0/+113
| | | | | | MTU needs to be explicitly set as default value is too low. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: use upstream accepted Ethernet driver patchesRafał Miłecki2021-02-1212-156/+1128
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* realtek: add support for Netgear GS108T v3Michael Mohr2021-02-122-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear GS108T v3 is an 8 port gigabit switch with PoE-PD support on port 1. The two prior versions were built using eCos and are not currently compatible with OpenWRT. The GS108T v3 is quite similar to both the GS110TPP v1 and GS110TP v3, all of which use the same firmware image from Netgear. For this reason, the device tree is identical aside from the model and compatible values. All of the above feature a dual firmware layout, referred to as Image0 and Image1 in the Netgear firmware. Hardware specification ---------------------- * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12) * 32MB 3v NOR SPI Flash (Macronix MX25L25635F or Winbond W25Q256JVFIQ) * RTL8231 GPIO extender to control the LEDs and the reset button * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B) * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1 * Power is supplied via a 12V 1A barrel connector or 802.3af UART pinout ----------- J1 | [o]ooo ^ ||`------ GND | |`------- RX [TX out of the serial adapter] | `-------- TX [RX into the serial adapter] `---------- Vcc (3V3) [the square pin] The through holes are filled with PB-free solder which melts at 375C. They can also be drilled using a 0.9mm bit. Build configuration ------------------- * Target System: Realtek MIPS * Target Profile: Netgear GS108T v3 * Target Images -> ramdisk -> Compression: lzma * Disable other target images Boot initramfs image from U-Boot -------------------------------- 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Init network with `rtk network on` command 3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs108t-v3-initramfs-kernel.bin` command 4. Boot the image with `bootm` command The switch defaults to IP 192.168.1.1 and tries to fetch the image via TFTP from 192.168.1.111. Updating the installed firmware ------------------------------- The OpenWRT ramdisk image can be flashed directly from the Netgear UI. The Image0 slot should be used in order to enable sysupgrade. As with similar switches, changing the active boot partition can be accomplished in U-Boot as follows: 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Run `setsys bootpartition {0|1}` to select the boot partition 3. Run `savesys` followed by `boota` to proceed with the boot process Signed-off-by: Michael Mohr <akihana@gmail.com>
* realtek: refactor the Netgear GS110TPP v1 device treeMichael Mohr2021-02-122-225/+139
| | | | | | | | | | | | | | | | | | | Move most of the GS110TPP v1 device tree into a dtsi so that it can be shared with the GS108T v3. Additionally: * Use macros to simplify the ethernet and switch definitions * Zero-pad the offsets and sizes in the partition map to 8 digits each The spi-max-frequency value has been changed from 10MHz to 50MHz based on an analysis of the relevant datasheets. The current driver doesn't use this property, as the clock speed is fixed. However, it's required for this type of DT node, so that's why it's present here. The firmware partition has been split in half, since this is how the stock firmware uses it. This can be used to easily revert to a stock firmware if one is written to the second image area. Signed-off-by: Michael Mohr <akihana@gmail.com>
* realtek: add and use netgear_nge for the GS110PP v1Michael Mohr2021-02-121-6/+12
| | | | | | | | The netgear_nge device will be shared between the GS108T v3 (to be added in a later commit) and the GS110PP v1. It also enables LZMA compression for the ramdisk image. Signed-off-by: Michael Mohr <akihana@gmail.com>
* hostapd: reconfigure wps credentials on reloadRaphaël Mélotte2021-02-121-0/+187
| | | | | | | | | | This patch fixes a bug that prevents updating Multi-AP credentials after hostapd has started. It was sent to upstream hostapd here: https://patchwork.ozlabs.org/bundle/rmelotte/hostapd:%20update%20WPS%20credentials%20on%20SIGHUP/ Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
* hostapd: add notifications for management framesRaphaël Mélotte2021-02-122-2/+131
| | | | | | | | | | | | | | | | This patch allows other applications to get events management frames (for example: association requests). This is useful in Multi-AP context to be able to save association requests from stations. It has been sent to upstream hostapd in this series: https://patchwork.ozlabs.org/project/hostap/list/?series=217500 '700-wifi-reload.patch' is updated due to the introduction of '110-notify-mgmt-frames.patch'. Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
* ltq-ptm: Update VR9 PTM firmwareAntti Seppälä2021-02-128-312/+439
| | | | | | | | | | | | | | | After looking at various vendor GPL source code dumps I discovered that some of them contain updated versions of ltq-ptm driver when compared to what openwrt has. The driver update is mostly cursory (simple changes to comments, whitespace, formatting etc.) or adds debug features not used by openwrt. However the updated driver also contains a later version of PTM firmware which is extracted and included in this commit along with bits to correctly identify its version when driver loads. Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
* ath79: fix USB power GPIO for TP-Link TL-WR810N v1Adrian Schmutzler2021-02-111-1/+1
| | | | | | | | | | | | | | | | | | The TP-Link TL-WR810N v1 is known to cause soft-brick on ath79 and work fine for ar71xx [1]. On closer inspection, the only apparent difference is the GPIO used for the USB regulator, which deviates between the two targets. This applies the value from ar71xx to ath79. Tested successfully by a forum user. [1] https://forum.openwrt.org/t/tp-link-tl-wr810n-v1-ath79/48267 Fixes: cdbf2de77768 ("ath79: Add support for TP-Link WR810N") Fixes: FS#3522 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ELECOM WRC-1167FSINAGAKI Hiroshi2021-02-114-0/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 5.4 to 5.4.97John Audia2021-02-1116-35/+26
| | | | | | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: bcm27xx 950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch bcm53xx 180-usb-xhci-add-support-for-performing-fake-doorbell.patch layerscape 302-dts-0008-arm64-dts-ls1046a-accumulated-change-to-ls1046a-boar.patch 820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch 820-usb-0018-MLK-18794-1-usb-host-xhci-add-.bus_suspend-override.patch Build system: x86_64 Build-tested: bcm27xx/bcm2711, ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions/everything functional. Signed-off-by: John Audia <graysky@archlinux.us> [remove quilt comment, fix/adjust 820-usb-* layerscape patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* arm-trusted-firmware-tools: add patch to pass LDFLAGSDaniel Golle2021-02-101-0/+11
| | | | | | This should hopefully fix builds on the buildbot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* at91: use SPDX license identifiers on DTS filesAdrian Schmutzler2021-02-105-10/+10
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 01:20:54 +0000