aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: disable touchscreen symbolsChristian Lamparter2019-02-282-6/+104
| | | | | | | | | | | This patch removes the obsolete touchscreen config symbols and all disables all remaining ones in the generic config. Generated by running drivers/input/touchscreen/Kconfig sed -n 's/^config[[:space:]]\(.*\)/# CONFIG_\1 is not set/p' Kconfig |\ sort -d Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: fix geode image buildsChristian Lamparter2019-02-282-0/+7
| | | | | | | | | | This patch adds the disabled DRM_RADEON and DRM_AMDGPU config symbols from the x86' config to the generic target configs. The existing symbols in the x86' configs are kept for now, until we know whenever we want to remove such symbols or not (see Github PR #1831, #1825, #1828). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Qxwlan E2600AC C1 and C2张鹏2019-02-2815-16/+980
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for COMFAST CF-E120A v3Roger Pueyo Centelles2019-02-283-0/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless CPE with two Ethernet ports and a 802.11an radio. Specifications: - AR9344 SoC - 535/400/267 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 5 GHz, up to 25 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add TP-Link TL-WR802N-v4 supportMarcel Jost2019-02-283-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N-v4. https://openwrt.org/toh/tp-link/tl-wr802n Specification: - MT7628N (580 MHz) - 64 MB RAM - 8 MB FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet - 1x LED Flash instruction: The only way to flash the image in TL-WR802N v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 10 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Marcel Jost <majo@icutech.ch>
* ramips: use generic board detection for Wavlink WL-WN575A3Thomas Vincent-Cross2019-02-284-17/+15
| | | | | | Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices. Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* ramips: various Wavlink WL-WN575A3 fixesThomas Vincent-Cross2019-02-281-4/+3
| | | | | | | | | * assign pinmux groups to gpio function for LEDs/buttons * rename flash node to be more generic in line with other device nodes * remove useless/incorrect eeprom property from wmac node * correct base mac address for embedded switch Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* wireguard: bump to 0.0.20190227Jason A. Donenfeld2019-02-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * wg-quick: freebsd: allow loopback to work FreeBSD adds a route for point-to-point destination addresses. We don't really want to specify any destination address, but unfortunately we have to. Before we tried to cheat by giving our own address as the destination, but this had the unfortunate effect of preventing loopback from working on our local ip address. We work around this with yet another kludge: we set the destination address to 127.0.0.1. Since 127.0.0.1 is already assigned to an interface, this has the same effect of not specifying a destination address, and therefore we accomplish the intended behavior. Note that the bad behavior is still present in Darwin, where such workaround does not exist. * tools: remove unused check phony declaration * highlighter: when subtracting char, cast to unsigned * chacha20: name enums * tools: fight compiler slightly harder * tools: c_acc doesn't need to be initialized * queueing: more reasonable allocator function convention Usual nits. * systemd: wg-quick should depend on nss-lookup.target Since wg-quick(8) calls wg(8) which does hostname lookups, we should probably only run this after we're allowed to look up hostnames. * compat: backport ALIGN_DOWN * noise: whiten the nanoseconds portion of the timestamp This mitigates unrelated sidechannel attacks that think they can turn WireGuard into a useful time oracle. * hashtables: decouple hashtable allocations from the main device allocation The hashtable allocations are quite large, and cause the device allocation in the net framework to stall sometimes while it tries to find a contiguous region that can fit the device struct. To fix the allocation stalls, decouple the hashtable allocations from the device allocation and allocate the hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall back to vmalloc with little resistance. * chacha20poly1305: permit unaligned strides on certain platforms The map allocations required to fix this are mostly slower than unaligned paths. * noise: store clamped key instead of raw key This causes `wg show` to now show the right thing. Useful for doing comparisons. * compat: ipv6_stub is sometimes null On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has been disabled with a command line flag or other failures. * Makefile: don't duplicate code in install and modules-install * Makefile: make the depmod path configurable * queueing: net-next has changed signature of skb_probe_transport_header A 5.1 change. This could change again, but for now it allows us to keep this snapshot aligned with our upstream submissions. * netlink: don't remove allowed ips for new peers * peer: only synchronize_rcu_bh and traverse trie once when removing all peers * allowedips: maintain per-peer list of allowedips This is a rather big and important change that makes it much much faster to do operations involving thousands of peers. Batch peer/allowedip addition and clearing is several orders of magnitude faster now. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* tools: migrate from squashfs4 to squashfskit4Alexander Couzens2019-02-2813-1408/+9
| | | | | | | | | squashfskit is a fork of the squashfs-tools. squashfskit creates reproducible filesystems and includes many of the distro patches. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Tested-by: Paul Spooren <mail@aparcar.org>
* openssl: bump to release 1.1.1bEneas U de Queiroz2019-02-279-643/+5
| | | | | | | | | | | This is bugfix release that incorporated all of the devcrypto engine patches currently in the tree. The cleaning procedure in Package/Configure was not removing the dependency files, causing linking errors during a rebuild with different options. It was replaced by a simple make clean. Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
* odhcpd: update to latest git HEADHans Dedecker2019-02-271-3/+3
| | | | | | 16c5b6c ubus: always trigger an update if interface is not found Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* omcproxy: define configuration fileDavid Santamaría Rogado2019-02-271-1/+5
| | | | | | | omcproxy's configuration is lost on every update or installation. Avoid it by defining the configuration file. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* Revert "iw: compile with LTO enabled"Mantas Pucka2019-02-261-3/+2
| | | | | | | | | | | | | After update to 5.0.1 iw-full package failed to display command list on ipq40xx arch. Root cause was found to be LTO reordering causing incorrect detection of command struct size in: iw.c:552 cmd_size = labs((long)&__section_set - (long)&__section_get); This reverts commit ef16a394d2b24a363b50b5b4720cb23fe156c9da. Signed-off-by: Mantas Pucka <mantas@8devices.com>
* strace: update to version 2.26Hauke Mehrtens2019-02-263-3/+94
| | | | | | The new patch is a backport from current strace master. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tools/isl: update to 0.20Syrone Wong2019-02-261-2/+2
| | | | Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
* toolchain/binutils: Add binutils 2.32Daniel Engberg2019-02-267-0/+110
| | | | | | Add binutils 2.32 to repo Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* toolchain: Update to GCC 8.3.0Daniel Engberg2019-02-2622-7/+6
| | | | | | | | | Update GCC to 8.3.0 Refresh patches Allow GCC to be used for ARC Source: https://github.com/openwrt/openwrt/pull/1803#issuecomment-462334890 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* toolchain/gcc: Remove workaround for GCC 4.8Daniel Engberg2019-02-261-5/+2
| | | | | | GCC 4.8 was removed a long time ago... Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* popt: Use modern toolchain logicDaniel Engberg2019-02-261-6/+1
| | | | | | Replace define Build/Configure with CONFIGURE_ARGS Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* elfutils: fix install .so globMatt Merhar2019-02-261-3/+3
| | | | | | | Only libelf was being packaged correctly - libdw and libasm included just the symlinks. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* sunxi: add support for Orange Pi OneAleksander Jan Bajkowski2019-02-262-0/+17
| | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 512MB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard header: SPI, I2C, GPIO, UART USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ath79: fix support-list for TP-Link WDR3600David Bauer2019-02-261-1/+1
| | | | | | | | | | | | The TP-Link WDR3600 shares the same machine-code in the ar71xx target, thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list metadata to allow non-forced sysupgrades from ar71xx to ath79. With this, it is possible to flash a WDR4300 image on the WDR3600. It is no problem however, as the only difference is the 5GHz WiFi chip which has 3SS instead of 2SS. Both work with either image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add ar71xx support-list entry for Fritz4020David Bauer2019-02-261-0/+1
| | | | | | | This adds the support-list entry the AVM FRITZ!Box 4020 expects in the ar71xx target to allow non-forced sysupgrades from ar71xx to ath79. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: GL.iNet AR300M family: correct LED definitionsAndreas Ziegler2019-02-262-8/+2
| | | | | | | | remove USB as this is no LED but power control rename WiFi LED with correct color red (like in stock firmware) set middle LED to be used for LAN link/activity Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
* ath10k-ct: fix incorrect multicast/broadcast rate settingSven Eckelmann2019-02-264-2/+82
| | | | | | | | | | | | | | | | | If no mcast_rate is set for the wifi-iface then there is no rate_idx (0) set for the bss. This can break for example 5GHz meshpoint interfaces because 0 maps to a CCK rate (11Mbit/s). It must also be avoided that the ath10k-ct internal state for the rates is not synced with the mac80211 rates state. Otherwise, the user specified rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be set on startup. And a short while after that, ath10k-ct specific code in ath10k_check_apply_special_rates is missing a valid rate in its own structures and is then recalculating a new default rate. This default rate is in most situations not the requested rate. Fixes: 4df3c71cd4c5 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* mac80211: ath10k: fix incorrect multicast/broadcast rate settingSven Eckelmann2019-02-262-1/+44
| | | | | | | | | If no mcast_rate is set for the wifi-iface then there is no rate_idx (0) set for the bss. This breaks for example 5GHz meshpoint interfaces because 0 maps to a CCK rate (11Mbit/s). Fixes: db90c243a0b9 ("mac80211: update to version based on 4.19-rc4") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* mac80211: Add WDS / 4addr fix for ath10k supported devicesHauke Mehrtens2019-02-261-0/+107
| | | | | | | | | | This should fix the WDS / 4addr mode with ath10k and probably other devices. This patch was found here: https://patchwork.kernel.org/patch/10692383/ Fixes: d9eefa7a7031 ("mac80211: rebase ontop of v4.18.5") Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: rt2x00: fix crash on release_firmwareStanislaw Gruszka2019-02-262-5/+5
| | | | | | | | | | Fix crash due to passing invalid r2x00dev->eeprom_file pointer to release_firmware(). Since we copy eeprom data with EEPROM_SIZE in rt2800_read_eeprom() we can use eeprom_file->size as marker if the file was crated by request_firmware(). Acked-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
* mt76: update to the latest versionFelix Fietkau2019-02-261-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 28d81ff mt76x0: eeprom: fix VHT mcs{8,9} rate power offset 6e33ce6 mt76: move mt76_mcu_msg_alloc in mt76-core 4637f95 mt76: move mt76_mcu_get_response in mt76-core 1763cb0 mt76: move mt76_mcu_rx_event in mt76-core 4db9d75 mt76x0: mcu: remove useless commented configuration 91d0455 mt76: move mt76_dma_tx_queue_skb_raw in mt76-core module 0e8e53f mt76: remove add_buf pointer in mt76_queue_ops db47920 mt7603: rely on mt76_mcu_msg_alloc routine 471c447 mt7603: rely on mt76_mcu_get_response routine cacc986 mt7603: rely on mt76_mcu_rx_event routine 11ab620 mt7603: rely on mt76_tx_queue_skb_raw common routine 82fa312 mt7603: move alloc_dev common code in mt76_alloc_device 47d5922 mt76: move alloc_device common code in mt76_alloc_device c50c993 mt76x2u: remove mt76x2u_alloc_device routine 6ed5b7a mt76x0: remove mt76x0u_alloc_device routine e32e249 mt76x2: remove mt76x2_alloc_device routine 6aacd1e mt76: change the return type of mt76_dma_attach() a10e9e5 mt76x02u: use usb_bulk_msg to upload firmware a774ff6 mt76: usb: fix possible NULL pointer dereference in mt76u_mcu_deinit c2877bc mt76: usb: fix possible memory leak in mt76u_buf_free a5cfe96 mt76: usb: do not run mt76u_queues_deinit twice 1e4db14 mt76: usb: move mt76u_check_sg in usb.c 302406b mt76: usb: do not use sg buffers for mcu messages 8ab5267 mt76: usb: use a linear buffer for tx/rx datapath if sg is not supported a0a3505 mt76: usb: introduce disable_usb_sg parameter 0cee180 mt76: usb: use dev_err_ratelimited instead of dev_err in mt76u_complete_rx 1bb97c4 mt76x02u: remove bogus check and comment padding 2cbc2d4 mt76: Use the correct hweight8() function f18e03a mt76x0u: fix suspend/resume 6231336 mt76: mt76x02: fix TSF sync mode 783da04 mt76: mt76x02: fix beacon timer drift adjustment 43d2507 mt76: mt76x02: fix beacon timer issue 59a6587 mt76: mt76x02: only reset beacon drift counter when enabling beacons 8c8eb98 mt76: mt76x02: issue watchdog reset on MCU request timeout 52161d2 mt76: mt76x02: fix ED/CCA enabling/disabling 5e7ecce mt76: mt76x2: unify mt76x2[u]_mac_resume 18af219 mt76: mt76x02: set MT_TXOP_HLDR_TX40M_BLK_EN for mt76x2 e5747b2 mt76usb: allow mt76u_bulk_msg be used for reads 2437a9a mt76usb: use synchronous msg for mcu command responses e4250c9 mt76usb: remove usb_mcu.c 8b1110e mt76: usb: fix warning in mt76u_buf_free 89215f6 mt76: usb: introduce mt76u_fill_bulk_urb routine 523e374 mt76: usb: simplify rx buffer allocation ffe1292 mt76: usb: simplify mt76u_tx_build_sg routine e2a9d40 mt7603: fix ba window size selection b040ef7 mt76: remove no longer used routine declarations 645ef43 mt76: usb: check urb->num_sgs limit in mt76u_process_rx_entry fd315bd mt7603: disable dynamic sensitivity adjustment by default Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: qsdk-ipq-*: include dtc in PATH before calling mkimagePiotr Dymacz2019-02-261-2/+2
| | | | | | | Use 'dtc' from kernel sources instead of relying on host tool. Fixes: bf4630e5adb4 ("build: add helpers for generating QSDK sysupgrade compatible images") Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for ALFA Network AP120C-ACPiotr Dymacz2019-02-261-3/+4
| | | | | | While at it, fix alphabetical order. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: add support for ALFA Network AP120C-ACPiotr Dymacz2019-02-2610-4/+742
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 4x LED (all driven by GPIO) - 1x button (reset) - 1x USB 2.0 (optional, not installed in indoor version) - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) Flash instruction: 1. This board uses dual-image feature (128 MB NAND is divided into two 64 MB partitions: 'rootfs1' and 'rootfs2'). 2. Before update, make sure your device is running firmware no older than v1.1 (previous versions have incompatible U-Boot). 3. Use 'factory' image in vendor GUI or for sysupgrade tool, without preserving settings. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq-wifi: add board-2.bin for ALFA Network AP120C-ACPiotr Dymacz2019-02-262-1/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: add support for Macronix MX35LF1GE4AB SPI NANDPiotr Dymacz2019-02-261-0/+13
| | | | | | | | | | Without a proper SPI NAND support (SPI NAND framework is available in kernel >= 4.19) the only way to make such flash working is to include it in raw/parallel NAND subsystem support and combine with mt29f staging driver. Obviously, this approach isn't going to be accepted by upstream (similar support for Winbond W25N01GV was rejected). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* build: add helpers for generating QSDK sysupgrade compatible imagesPiotr Dymacz2019-02-252-0/+73
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qualcomm SDK (QSDK) sysupgrade compatible images for IPQ40xx, IPQ806x and IPQ807x use FIT format together with 'dumpimage' tool from U-Boot for verifying and extracting them. Based on 'images' sections names, corresponding mtd partitions are flashed. For example, in case of NOR-only boards, below mapping is used (section name -> mtd name): hlos* -> 0:HLOS rootfs* -> rootfs And for boards with NAND (kernel inside UBI): ubi* -> rootfs Above mappings come from unmodified QSDK sources and might be wrong for boards running custom or modified QSDK-based firmware. Some of vendors adjust them to meet their modified mtd layout or features like recovery or dual-image support. This adds simple script 'mkits-qsdk-ipq-image.sh' (based on 'mkits.sh') for generating FIT images tree source files, compatible with the QSDK sysupgrade format. Resulting images can be used for initial (factory -> OpenWrt) installation and would work both in CLI and GUI. The script is universal in a way it allows to include as many sections as needed. To make use of it, two generic/basic build recipes for NOR and NAND based boards are also included in 'image-commands.mk': Build/qsdk-ipq-factory-nand Build/qsdk-ipq-factory-nor Example usage for board with UBI in NAND: IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: bump 4.19 to 4.19.25Koen Vandeputte2019-02-253-6/+6
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.103Koen Vandeputte2019-02-255-11/+11
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.160Koen Vandeputte2019-02-254-7/+7
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 3.18 to 3.18.136Koen Vandeputte2019-02-251-2/+2
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-6974 Compile-tested: adm5120 Runtime-tested: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: add missing config symbolsStijn Tintel2019-02-251-0/+4
| | | | | | | | | | The addition of kmod-input-touchscreen-ads7846 enabled INPUT_TOUCHSCREEN, which exposes several other symbols on various targets. Add those symbols to the generic kernel configs to fix build. Fixes: 77a54bbf13bf ("kernel: add kmod-input-touchscreen-ads7846") Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* odhcpd: update to latest git HEAD (FS#2142)Hans Dedecker2019-02-251-3/+3
| | | | | | | | 9e9389c dhcpv4: fix adding assignment in list (FS#2142) e69265b dhcpv4: fix static lease lookup afbd7dd dhcp: rework assignment free logic Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: fix kmod-input-touchscreen-ads7846 depsStijn Tintel2019-02-251-1/+1
| | | | | | | | | | On targets that don't have input support enabled in the kernel config, building kmod-input-touchscreen-ads7846 fails due to a missing dependency on kmod-input-core. Add the dependency to fix this. Fixes: 77a54bbf13bf ("kernel: add kmod-input-touchscreen-ads7846") Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* package/dnsmasq: add max_ttl/min_cache_ttl/max_cache_ttlAlexander Couzens2019-02-242-1/+4
| | | | | | | | | max_ttl - limit the ttl in the dns answer if greater as $max_ttl min_cache_ttl - force caching of dns answers even the ttl in the answer is lower than the $min_cache_ttl max_cache_ttl - cache only dns answer for $max_cache_ttl. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* kernel: add kmod-input-touchscreen-ads7846Stijn Tintel2019-02-244-0/+25
| | | | | | | This module adds support for ADS7846 based touchscreens used in devices like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add kmod-fb-tft-ili9486Stijn Tintel2019-02-241-0/+16
| | | | | | | This module adds support for the ILI9486 LCD controller used in devices like the Waveshare 3.5" and 4" LCD displays designed for Raspberry Pi. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add kmod-fb-tftStijn Tintel2019-02-243-0/+92
| | | | | | | | This module adds support for small TFT LCD display modules. While this module also exists in the 4.9 kernel, we are not going to support this kernel in the next major release, so don't make it available for 4.9. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add kmod-fb-sys-ramStijn Tintel2019-02-241-10/+27
| | | | | | | | | | | The kernel modules that provide support for framebuffers in system RAM are currently included in the kmod-drm-imx package. Move them to a separate package, so that other modules can depend on them. Increase the autoload order of the drm-imx* packages to load the modules after loading the fb modules they depend on. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add kmod-iio-ccs811Stijn Tintel2019-02-231-0/+17
| | | | | | | This module supports the AMS CCS811 VOC sensor. Tested on Raspberry Pi Zero W and ODROID C2. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* dnsmasq: prefer localuse over resolvfile guessworkYousong Zhou2019-02-232-5/+5
| | | | | | | | | This makes it clear that localuse when explicitly specified in the config will have its final say on whether or not the initscript should touch /etc/resolv.conf, no matter whatever the result of previous guesswork would be Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kernel: bump 4.19 to 4.19.24Koen Vandeputte2019-02-222-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>