aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* download.mk: restore the old dl_method implementationYousong Zhou2018-06-291-1/+17
| | | | | | | | Seems like the python download.py dl_method call causes serious performance regression for fresh "make defconfig" as reported in FS#1621. GitHub tarball download will also be disabled with this Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* swconfig: swlib_map_settings(): change return type to voidAlexander Couzens2018-06-291-1/+1
| | | | | | | | The return value of the function isn't used anywhere. Fixes missing return value, CID 1329717. Found-by: Coverity Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* swconfig: fix un-initialized return valueAlexander Couzens2018-06-291-2/+3
| | | | | | | Fix CID 1330844 Found-by: Coverity Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ath79: add support for Unifi AC MeshAdrian Schmutzler2018-06-286-19/+40
| | | | | | | | | The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for more AR7241 TP-Link boardsDmytro Smyrnov2018-06-288-0/+266
| | | | | | | | | | | Its common AP99(AR7241) platform with following devices: TP-Link TL-WR841N/ND v7 (SoC AR7241 / Wifi AR9287 / without USB) TP-Link TL-MR3220 v1 (SoC AR7241 / Wifi AR9285 / USB support) TP-Link TL-MR3420 v1 (SoC AR7241 / Wifi AR9287 / USB support) Signed-off-by: Dmytro Smyrnov <dioptimizer@hotmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: small wr1043nd-v4 fixesLucian Cristian2018-06-284-23/+36
| | | | | | | | | | | | | | | - fix sysupgrade check - move usb to v4 dts because v5 doesn't have it - make wan mac address behave like ar71xx target - add orange wan led support, it can be userspace activated like: on: echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger off: echo none > /sys/class/leds/tp-link\:orange\:wan/trigger Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add support for Ubiquiti UniFi AC-ProLucian Cristian2018-06-286-126/+178
| | | | | | | | rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: sync naming of Ubiquiti devicesAdrian Schmutzler2018-06-284-7/+8
| | | | | | | Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Remove all memory nodes defined in dtsChuanhong Guo2018-06-2824-120/+0
| | | | | | | This target can automatically detect the correct memory size and we've been using it for long in ar71xx. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* treewide: gpio-export: add error handlingMathias Kresin2018-06-283-3/+9
| | | | | | | | Check if the GPIO is valid (or set at all). If no GPIO is set in the devicetree, a gpiolib related kernel warning + stacktrace is shown during boot and gpio-export reports GPIOs as exported albeit none really is. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop gpio export patchMathias Kresin2018-06-281-166/+0
| | | | | | The hack isn't used by any board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: switch the NBG6817 wlan LEDs from amber to whiteStefan Lippers-Hollmann2018-06-281-2/+0
| | | | | | | | | | | | | | | | | The original device support patch configured the amber wlan LEDs (which are meant as error indicator by the OEM) controlled by the SOC's GPIO as wlan traffic indicators, as the correct white wlan LEDs are connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were not accessible. The recent addition of GPIO/ LED support to ath10k now makes it possible to use the correct white LEDs instead - and "mac80211: ath10k: use tpt LED trigger by default" also enables them by default. While both LEDs are independent of each other (two separate LEDs sharing one light tunnel), triggering both on wlan traffic is not the intended behaviour (bright yellow light). Tested on the ZyXEL NBG6817. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ramips: move mt7620n i2c_pins definition to right placeAndrey Jr. Melnikov2018-06-281-7/+7
| | | | | | | | | | Move to i2c pins pinmux node to the pinctrl node. Fixes: a0685deec458 ("ramips: Add i2c support for mt7620n") Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com> [fix commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* qos-scripts: fix uci callback handlingTony Ambardar2018-06-283-29/+29
| | | | | | | | | | | | | | | | | The previous callback code was fragile, dependent on some UCI callback bugs and side-effects now fixed in master commit 73d8a6ab. Update scripts to use callbacks where appropriate and necessary, while using normal UCI config parsing for all else. This results in smaller, simpler, more robust code. Use callbacks in generate.sh to only process 'interface' defaults and the varying entries for 'reclassify', 'default' and 'classify' sections. Also switch qos-stat to use non-callback UCI handling. The current changes work independently of 73d8a6ab (i.e. both before and after), and are consistent with UCI config parsing documentation. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq806x: remove "firmware" partition definition from netgear routersHannu Nyman2018-06-274-20/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the "firmware" partition definition from the DTS of R7800 to fix sysupgrade. Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x and that causes mtd to misbehave as additional kernel and ubi partitions are detected from inside the "firmware" partition. [ 1.111324] 0x000001480000-0x000001880000 : "kernel" [ 1.121005] 0x000001880000-0x000007900000 : "ubi" [ 1.283912] 0x000007900000-0x000008000000 : "reserve" [ 1.296407] 0x000001480000-0x000007900000 : "firmware" [ 1.468043] no rootfs found after FIT image in "firmware" [ 2.426860] 2 uimage-fw partitions found on MTD device firmware [ 2.426931] 0x000001480000-0x000001880000 : "kernel" [ 2.440420] 0x000001880000-0x000007900000 : "ubi" Both kernel and ubi are already defined in DTS, so this duplication leads into errors in sysupgrade: Writing from <stdin> to kernel ... ubiattach: error!: strtoul: unable to parse the number '6 mtd10' ubiattach: error!: bad MTD device number: "6 mtd10" The partition is defined to same area as kernel+ubi, and is not needed for sysupgrade anymore. Remove it to fix things. Only tested for the R7800 but all of them should behave equal. Fixes: FS#1617 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [squashed commits, add "tested on" note] Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: include package directory in sha256sums when running on buildbotJo-Philipp Wich2018-06-272-2/+3
| | | | | | | | | | In order to be able to better compare files to sync in the future, include all BIN_DIR subdirectories in the checksum calculation. To not break existing applications, restrict the recursive checksumming to CONFIG_BUILDBOT for now. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* scripts/download.py: use a more terse api for fetching git commit dateYousong Zhou2018-06-271-2/+2
| | | | | | | | | | | The previous api [1] includes in its response patch data among other things, as such the response size can vary and be big. Use another api[2] to improve it a bit [1] Get a single commit, Repositories, https://developer.github.com/v3/repos/commits/#get-a-single-commit [2] Git Commits, Git Data, https://developer.github.com/v3/git/commits/#get-a-commit Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ramips: add switch port index for I-O DATA WN-GX300GRINAGAKI Hiroshi2018-06-271-2/+2
| | | | | | | | | | | WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are orderd on the device as follows: 4 3 2 1 0 1-4: lan 0: wan Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* uboot-kirkwood: fix malformed boot configurationAlberto Bursi2018-06-278-8/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With current uboot default configuration the bootloader will fail to start the OpenWrt firmware with the following error: ----- unexpected character 'b' at the end of partition Error initializing mtdparts! incorrect device type in ubi Partition ubi not found! Error, no UBI device/partition selected! Wrong Image Format for bootm command Error occured, error code = 112 ----- If the uboot configuration is examined with printenv I can see that mdtparts line (on a nsa310) is wrong: ----- mtdparts=mtdparts=orion_nand:0x0c0000(uboot), 0x80000(uboot_env),0x7ec0000(ubi)bootargs_root= ---- The "bootargs_root=" that was appended to it should not be there. Fix the issue by adding a \0 line terminator at the end of affected lines, mimicking what is also done by uboot upstream. This issue was detected and confirmed on a nsa310, nsa325 and a pogoplug v4, but it's not hardware-specific, so apply the same fix to other devices as well. Note that the issue is with the uboot's integrated boot configuration, which is not used unless the uboot configuration in flash is unavailable (erased or corrupted), which happens only on first time installation, or if the user deletes the uboot configuration when upgrading uboot. People just upgrading from an older uboot without erasing their previous uboot configuration stored in flash would not have noticed this issue. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* uboot-kirkwood: fix whitespacesAlberto Bursi2018-06-278-29/+29
| | | | | | remove whitespaces from the patches Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* firmware-utils: tplink-safeloader: switch tl-wr1043nd-v4 to dynamic partitionsLucian Cristian2018-06-273-10/+5
| | | | | | | Use the new dynamic partition split in tplink-safeloader so we no longer have to worry about kernel size increases. Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* base-files: add menuconfig option for HOME_URLMathias Kresin2018-06-273-1/+12
| | | | | | | | | | Add a menuconfig option to set the HOME_URL exposed in /usr/lib/os-release independent from the LEDE_DEVICE_MANUFACTURER_URL. Fixes: FS#1123 Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: download code from github using archive APIYousong Zhou2018-06-272-31/+464
| | | | | | | | | | | | | | | | | | | | | | | | | | A new python script scripts/download.py is added to fetch tarballs using GitHub archive API [1], then repack in a reproducible way same as the current DownloadMethod/git GitHub imposes a 60 reqs/hour rate limit on unauthenticated API access[2]. This affects fetching commit date for feeding tar --mtime= argument. However, observation indicates that archive download is NOT subject to this limit at the moment. In the rare cases where download fails because of this, we will falback to using DownloadMethod/git The missing piece in the GitHub API is that it cannot provide in the tarball dependent submodules's source code. In that case, the implementation will also fallback to using DownloadMethod/git [1] Get archive link, https://developer.github.com/v3/repos/contents/#get-archive-link [2] Rate limiting, https://developer.github.com/v3/#rate-limiting v2 <- v1: - allow passing multiple urls with --urls argument - add commit ts cache. can be helpful on retry Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* wireguard: bump to 0.0.20180625Kevin Darbyshire-Bryant2018-06-261-2/+2
| | | | | | | | | | | | | | | | | | | | dfd9827 version: bump snapshot 88729f0 wg-quick: android: prevent outgoing handshake packets from being dropped 1bb9daf compat: more robust ktime backport 68441fb global: use fast boottime instead of normal boottime d0bd6dc global: use ktime boottime instead of jiffies 18822b8 tools: fix misspelling of strchrnul in comment 0f8718b manpages: eliminate whitespace at the end of the line 590c410 global: fix a few typos bb76804 simd: add missing header 7e88174 poly1305: give linker the correct constant data section size fd8dfd3 main: test poly1305 before chacha20poly1305 c754c59 receive: don't toggle bh Compile-tested-for: ath79 Archer C7 v2 Run-tested-on: ath79 Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mac80211: make rtl8xxxu buils againJohn Crispin2018-06-261-0/+38
| | | | | | we only wanted to drop rtl8xxxue support Signed-off-by: John Crispin <john@phrozen.org>
* mac80211: rtl8xxxu: drop support patchesJohn Crispin2018-06-2658-3569/+0
| | | | | | | | | After a very enlightening but unfortunately far too short exchange with Jes we mutually agreed to drop the patches. They are unfortunately not ready yet. Acked-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: John Crispin <john@phrozen.org>
* odhcpd: update to latest git HEADHans Dedecker2018-06-261-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | 81a281e dhcpv6-ia: fix border assignment size setting a2ffc59 dhcpv6-ia: fix status code for not on link IAs 5b087a6 dhcpv6-ia: improve error checking in assign_pd() c9114a1 config: fix wrong assignment bb8470f dhcpv4: delay forced renew transaction start 62a1b09 dhcpv4: fix DHCP address space logic d5726ff dhcpv4: improve logging when sending DHCP messages 9484351 odhcpd: call handle_error when socket error can be retrieved c45e2eb dhcpv6: fix out of bounds write in handle_nested_message() c2ff5af dhcpv6-ia: log renew messages as well 676eb38 router: fix possible segfault in send_router_advert() 392701f odhcpd: fix passing possible negative parameter 029123b treewide: switch to C-code style comments 6b79748 router: improve error checking 12e21bc netlink: fix incorrect sizeof argument d7aa414 dhcpv6: improve error checking in dhcpv6_setup_interface() 373495a ubus: fix invalid ipv6-prefix json 79d5e6f ndp: improve error checking d834ae3 dhcpv4: fix error checking in dhcpv4_setup_interface() f2aa383 dhcpv4: fix out of bound access in dhcpv4_put 4591b36 dhcpv4: improve error checking in dhcpv4_setup_interface() 4983ee5 odhcpd: fix strncpy bounds Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* package/utils/e2fsprogs: Update to 1.44.2Daniel Engberg2018-06-261-2/+2
| | | | | | Update e2fsprogs to 1.44.2 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ipq40xx: add support for the ZyXEL NBG6617Christian Lamparter2018-06-2615-2/+676
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ZyXEL NBG6617 Hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz NOR: 32 MiB Macronix MX25L25635F ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS Serial: WARNING: The serial port needs a TTL/RS-232 3.3v level converter! The Serial setting is 115200-8-N-1. The 1x4 .1" header comes pre-soldered. Pinout: 1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX first install / debricking / restore stock: 0. Have a PC running a tftp-server @ 192.168.1.99/24 1. connect the PC to any LAN-Ports 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file into the tftp-server root directory and rename it to just "ras.bin". 3. power-cycle the router and hold down the the WPS button (for 30sek) 4. Wait (for a long time - the serial console provides some progress reports. The u-boot says it best: "Please be patient". 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs flashes fast at the same time. You have to reboot the device and it should then come right up. Installation via Web-UI: 0. Connect a PC to the powered-on router. It will assign your PC a IP-address via DHCP 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234) 2. Go to the "Expert Mode" 3. Under "Maintenance", select "Firmware-Upgrade" 4. Upload the OpenWRT factory image 5. Wait for the Device to finish. It will reboot into OpenWRT without any additional actions needed. To open the ZyXEL NBG6617: 0. remove the four rubber feet glued on the backside 1. remove the four philips screws and pry open the top cover (by applying force between the plastic top housing from the backside/lan-port side) Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6617> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6617> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6617> ATSE NBG6617 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6617> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6617> ATGU |NBG6617# Co-authored-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer c7 v2Sibren Vasse2018-06-266-1/+278
| | | | Signed-off-by: Sibren Vasse <github@sibrenvasse.nl>
* ath79: add tl-wr2543-v1 supportLucian Cristian2018-06-265-0/+205
| | | | | | to switch between wlan leds we need a userspace implementation Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* iperf3: update to 3.6Philip Prindeville2018-06-261-3/+3
| | | | Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* netfilter: add bpf match supportAlin Nastac2018-06-263-0/+3
| | | | | | | | | Add xt_bpf modules to {kmod-ipt,iptables-mod}-filter. Match using Linux Socket Filter. Expects a BPF program in decimal format. This is the format generated by the nfbpf_compile utility. Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
* kernel: bump 4.14 to 4.14.51Kevin Darbyshire-Bryant2018-06-2613-360/+21
| | | | | | | | | | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Refresh patches. Remove patch that can be reverse applied: mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch Update patch that no longer applied: ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch Compiled-tested-for: lantiq, ramips Run-tested-on: lantiq BT hh5a, ramips MIR3g Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Michael Yartys <michael.yartys@protonmail.com> Tested-by: Rosen Penev <rosenp@gmail.com>
* ath79: add support for ON Networks N150RZoltan HERPAI2018-06-265-2/+32
| | | | | | | | | | | | This is a rebranded Netgear WNR612v2, specs are the same. - Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: add Netgear WNR612 v2Zoltan HERPAI2018-06-267-0/+189
| | | | | | | | | | | | | | | Netgear WNR612 v2: - cpu Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 As there is a rebranded WNR612v2 called ON Networks N150R, add a dtsi which includes all device support, and add a separate dts for the device only (with a separate one for the subsequent N150R). Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* firmware-utils: tplink-safeloader: switch RE350 to dynamic partitionsAlex Maclean2018-06-261-6/+2
| | | | | | | Use the new dynamic partition split in tplink-safeloader so we no longer have to worry about kernel size increases. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: RE350: add rootfs offset to headerAlex Maclean2018-06-261-1/+1
| | | | | | | Have mktplinkfw fill in the rootfs offset so the firmware splitter can find it without aligning to erase blocks. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* firmware-utils: tplink-safeloader: add dynamic partitionsAlex Maclean2018-06-261-13/+58
| | | | | | | | | | | | | | | | | Add support to dynamically split the firmware partition into os-image and file-system partitions. This is done by replacing those entries in the partition table with a single unified firmware partition, which is then split according to actual kernel image size. The factory image will have the file-system partition aligned to a 64K erase block, but the sysupgrade image skips this and aligns only the JFFS2 EOF marker to squeeze out more space. This should prevent further creeping updates to the kernel partition size while maximizing space for the overlay filesystem on smaller devices. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* firmware-utils: mktplinkfw: add rootfs offset for combined imagesAlex Maclean2018-06-261-1/+10
| | | | | | | | | | | Add an option (-O) to calculate rootfs offset for combined images. This is needed for the TP-Link mtdsplit driver to locate the rootfs when the start is not aligned to an erase block. This will be the case for sysupgrade images produced by tplink-safeloader with upcoming dynamic partition splitting. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* mac80211: enable ath10k LED support by defaultStijn Tintel2018-06-251-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | Commit 61d57a2f88b90ba951012e66c7c6fae9234c97b4 adds ath10k LED support, but doesn't add an option to actually enable it. After enabling this option, a LED named ath10k-phy0 appears in sysfs, and a trigger can be assigned to it. Since 60deb3cdef4a the default set trigger is the tpt one. Enable it by default, as most devices using ath10k chips shouldn't be severely space-constrained. There are likely many devices that can benefit from having it enabled, like my testing device. Before: text data bss dec hex filename 245311 8899 16 254226 3e112 ath10k_core.ko After: text data bss dec hex filename 245979 8899 16 254894 3e3ae ath10k_core.ko Tested on a D-Link DAP-2695-A1 (ar71xx). Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mac80211: ath10k: use tpt LED trigger by defaultMathias Kresin2018-06-251-0/+53
| | | | | | | | Use the tpt LED trigger for each created phy led. Ths way LEDs attached to the ath10k GPIO pins are indicating the phy status and blink on traffic. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link Archer C2Franz Flasch2018-06-256-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Winbond 25Q64BVSIG - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac - Switch: RTL8367RB Gigabit Switch - USB: Yes 1 x 2.0 Preparing a TFTP recovery image for initial flashing: Currently the only method to install openwrt for the first time is via TFTP download in u-boot. After first install you can use regular updates. WARNING: This method also overwrites the bootloader partition! Create a TFTP recovery image: 1) Download a stock TP-Link Firmware file here: https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware 2) Extract u-boot from the binary file: #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072 3) Now merge the sysupgrade image and the u-boot into one binary: #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin The resulting image can be flashed via TFTP recovery mode. Flash instructions: 1) To flash the recovery image, start a TFTP server from IP address 192.168.0.66 and serve the recovery image named ArcherC2V1_tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS/Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds. It will try to download the recovery image and flash it. It can take up to 20-25 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* ramips: fix ZyXEL Keenetic Viva switch configFranz Flasch2018-06-251-1/+1
| | | | | | | | | The rtl8367b driver never supported a mdio property and it is quite likely that the switch never worked for the board. Use the mii-bus property instead to manage the switch via a mdio bus. Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* kernel: rtl8366-smi: add Realtek switch management via mii-busFranz Flasch2018-06-252-17/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current version of rtl8366-smi module only supports Realtek switch managment via two gpio lines. This adds Realtek switch management via mii_bus. Tested on a Tp-link Archer C2 v1 (Mediatek SoC mt7620a based) dts-file configuration should look like this: rtl8367rb { compatible = "realtek,rtl8367b"; realtek,extif1 = <1 0 1 1 1 1 1 1 2>; mii-bus = <&mdio0>; }; &ethernet { status = "okay"; mtd-mac-address = <&rom 0xf100>; pinctrl-names = "default"; pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>; port@5 { status = "okay"; mediatek,fixed-link = <1000 1 1 1>; phy-mode = "rgmii"; }; mdio0: mdio-bus { status = "okay"; }; }; Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* kernel: rtl8367b: drop redundant compatibleMathias Kresin2018-06-251-1/+0
| | | | | | | Remove the compatible without vendor prefix. It is formal wrong and not used in the tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* dropbear: let opkg manage symlinks of ssh, scpYousong Zhou2018-06-251-3/+5
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* musl: sys/socket.h: fix SO_PEERSEC value on MIPSMatthias Schiffer2018-06-241-0/+59
| | | | | | | | | | Differing from all other archs supported by musl, MIPS defines SO_PEERSEC to 30 instead of 31. Patch has also been submitted upstream. Reported-by: Andrey Jr. Mlenikov <temnota.am@gmail.com> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: Add support for TP-Link CPE210 v2Adrian Schmutzler2018-06-237-11/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Notes: TP-Link does not use bootstrap registers so without this patch reference clock detects as 40MHz while it is actually 25MHz. This is due to messed up bootstrap resistor configuration on the PCB. Provided GPL code just forces 25MHz reference clock. That causes booting with completely wrong clocks, for example, CPU tries to boot at 1040MHz while the stock is 650MHz. So this PR depends on PR #672 to remove 40MHz reference clock. Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Add TP-Link Pharos v2 board detectionAdrian Schmutzler2018-06-232-14/+33
| | | | | | | | | | Add support for detecting TP-Link Pharos v2 boards. They use different format in product-info partition than v1 boards. Code was written mostly by Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-15 08:17:08 +0000