aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: move CONFIG_USB_MTU3 to generic configHauke Mehrtens2018-07-072-1/+1
| | | | | | | | | | | CONFIG_USB_MTU3 is not visible for the mediatek target by default, but only when CONFIG_USB_GADGET is set. This will config option will be remove with when running "make kernel_oldconfig", move this option to the generic config to prevent this. This fixes the build of the mt7623 subtarget of the mediatek target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: disable some DRM_PANEL config optionsHauke Mehrtens2018-07-071-0/+2
| | | | | | | The modules should not be build by default. This fixes the build of the zynq target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* toolchain/nasm: Backport GCC8 compatibility fix from upstream repoTed Hess2018-07-071-0/+15
| | | | Signed-off-by: Ted Hess <thess@kitschensync.net>
* ath79: disable unused drivers for tiny targetLucian Cristian2018-07-072-8/+8
| | | | | | | | | | | Shrink the tiny kernel by moving all switch and ethernet phy drivers to the generic kernel config instead of the target kernel config. All boards in the tiny and nand target are either ar7240 or ar9331 based, which don't support external xMII and therefore no external ethernet phy can be connected. None of the boards uses a realtek switch either. Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: optimize ath79 tiny target for sizeLucian Cristian2018-07-071-0/+2
| | | | | | the speed impact on tiny target is minimal and worth the size gained Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add support for UniFi AC-Mesh ProChristoph Krapp2018-07-076-23/+44
| | | | | | | | | The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except USB support. Furthermore for setting parameters like antenna gain it is helpful to know the exact device variant. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ramips: add support for Blueendless Kimax U35WFAdemar Arvati Filho2018-07-076-3/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908 Based on: https://github.com/lede-project/source/pull/965 Specification: - SoC: MediaTek MT7620N - CPU/Speed: 580 MHz - Flash-Chip: KH25L12835F Spi Flash - Flash size: 16 MiB - RAM: 64 MiB - LAN: 1x 100 Mbps Ethernet - WiFi SoC-integrated: 802.11bgn - 1x USB 2.0 - UART: for serial console Installation: 1. Download sysupgrade.bin 2. Open vendor web interface 3. Choose to upgrade firmware 3. After reboot connect via ethernet at 192.168.1.1 Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* ar71xx: factor out safe loader image build codeMathias Kresin2018-07-073-60/+44
| | | | | | | | | | Add a template for safeloader images and include it instead of overwriting variables defined in the common tp-link build commands. Split the existing tp-link templates to proper implement the safeloader template. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: drop unnecessary LOADER_TYPE variablesMathias Kresin2018-07-071-5/+1
| | | | | | | Drop the LOADER_TYPE variables in case no loader is used at all or move the variable to devices which are using a loader. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: get rid of copy-fileMathias Kresin2018-07-071-6/+4
| | | | | | | Use the provided image build variables to point the kernel-bin build command to the kernel we are interested in. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: mikrotik: cleanup nand image build codeMathias Kresin2018-07-071-14/+20
| | | | | | | | | | | | Use the LOADER_TYPE variable to specify that we need the elf preloader and append the loader via the corresponding build recipe. It allows to enable initramfs images again for mikrotik NAND images, which caused a build error before. Add the minor header only to the kernel of the sysupgrade images, as it is only required for the bootloader to find the kernel on flash. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for I-O DATA WN-AX1167GRINAGAKI Hiroshi2018-07-076-0/+197
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 64 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Stock firmware: In the stock firmware, WN-AX1167GR has two os images each composed of Linux kernel and rootfs. These images are stored in "Kernel" and "app" partition of the following partitions, respectively. (excerpt from dmesg): MX25L12805D(c2 2018c220) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 10 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config " 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "iNIC_rf" 0x000000060000-0x0000007e0000 : "Kernel" 0x000000800000-0x000000f80000 : "app" 0x000000f90000-0x000000fa0000 : "Key" 0x000000fa0000-0x000000fb0000 : "backup" 0x000000fb0000-0x000001000000 : "storage" The flag for boot partition is stored in "Key" partition, and U-Boot reads this and determines the partition to boot. If the image that U-Boot first reads according to the flag is "Bad Magic Number", U-Boot then tries to boot from the other image. If the second image is correct, change the flag to the number corresponding to that image and boot from that image. (example): ## Booting image at bc800000 ... Bad Magic Number,FFFFFFFF Boot from KERNEL 1 !! ## Booting image at bc060000 ... Image Name: MIPS OpenWrt Linux-4.14.50 Image Type: MIPS Linux kernel Image (lzma compressed) Data Size: 1865917 Bytes = 1.8 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK raspi_erase_write: offs:f90000, count:34 . . Done! Starting kernel ... Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AX1167GR 2. Connect power cable to WN-AX1167GR and turn on it 3. Access to "192.168.0.1" on the web browser and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and perform firmware update 5. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR 6. Wait ~180 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* libnl: bump to 3.4.0Konstantin Demin2018-07-074-31/+15
| | | | | | refresh patches Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
* uboot-imx: bump to 2018.03 which fixes the build issues with fdt64_t ↵Vladimir Vid2018-07-079-1636/+26
| | | | | | | | | | | redefinitions * change mx6qsabresd to mx6qsabres to match defconfig name * merge wanboard profiles since there is only one defconfig for the target device * move wanboard options from wandboard.h to defconfig * remove legacy patches Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* mac80211: initialize sinfo in cfg80211_get_stationSven Eckelmann2018-07-071-0/+42
| | | | | | | | | | | | | | | | | | | Most of the implementations behind cfg80211_get_station will not initialize sinfo to zero before manipulating it. For example, the member "filled", which indicates the filled in parts of this struct, is often only modified by enabling certain bits in the bitfield while keeping the remaining bits in their original state. A caller without a preinitialized sinfo.filled can then no longer decide which parts of sinfo were filled in by cfg80211_get_station (or actually the underlying implementations). cfg80211_get_station must therefore take care that sinfo is initialized to zero. Otherwise, the caller may tries to read information which was not filled in and which must therefore also be considered uninitialized. In batadv_v_elp_get_throughput's case, an invalid "random" expected throughput may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may switch to non-optimal neighbors for certain destinations. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ath10k-ct: search DT for BDF variant infoSven Eckelmann2018-07-073-1/+363
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Board Data File (BDF) is loaded upon driver boot-up procedure. The right board data file is identified on QCA4019 using bus, bmi-chip-id and bmi-board-id. The problem, however, can occur when the (default) board data file cannot fulfill the vendor requirements and it is necessary to use a different board data file. This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8. Something similar has to be provided for systems without SMBIOS but with device trees. No solution was specified by QCA and therefore a new one has to be found for ath10k. The device tree requires addition strings to define the variant name wifi@a000000 { status = "okay"; qcom,ath10k-calibration-variant = "RT-AC58U"; }; wifi@a800000 { status = "okay"; qcom,ath10k-calibration-variant = "RT-AC58U"; }; This would create the boarddata identifiers for the board-2.bin search * bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U * bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* config: add config option for KERNEL_TASKSTATSJeremiah McConnell2018-07-071-0/+21
| | | | | | | | | | In order for monitoring tools such as atop and htop to track and report i/o data, kernel support for task statistics and io accounting is required. Add a config option to enable building this support in the kernel. Signed-off-by: Jeremiah McConnell <miah@miah.com>
* mbedtls: Activate deterministic ECDSAHauke Mehrtens2018-07-071-18/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | With deterministic ECDSA the value k needed for the ECDSA signature is not randomly generated any more, but generated from a hash over the private key and the message to sign. If the value k used in a ECDSA signature or the relationship between the two values k used in two different ECDSA signatures over the same content is know to an attacker he can derive the private key pretty easily. Using deterministic ECDSA as defined in the RFC6979 removes this problem by deriving the value k deterministically from the private key and the content which gets signed. The resulting signature is still compatible to signatures generated not deterministic. This increases the size of the ipk on mips 24Kc by about 2 KByte. old: 166.240 libmbedtls_2.11.0-1_mips_24kc.ipk new: 167.811 libmbedtls_2.11.0-1_mips_24kc.ipk This does not change the ECDSA performance in a measurable way. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mbedtls: Disable MBEDTLS_SHA256_SMALLER implementationDaniel Engberg2018-07-071-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | Disable MBEDTLS_SHA256_SMALLER implementation, not enabled by default in upstream and reduces performance by quite a bit. Source: include/mbedtls/config.h Enable an implementation of SHA-256 that has lower ROM footprint but also lower performance. The default implementation is meant to be a reasonnable compromise between performance and size. This version optimizes more aggressively for size at the expense of performance. Eg on Cortex-M4 it reduces the size of mbedtls_sha256_process() from ~2KB to ~0.5KB for a performance hit of about 30%. The size of mbedtls increased a little bit: ipkg for mips_24kc before: 164.382 Bytes ipkg for mips_24kc after: 166.240 Bytes Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* mbedtls: Update to 2.11.0Daniel Engberg2018-07-076-32/+58
| | | | | | | | | | | | | | | | Update mbed TLS to 2.11.0 Disable OFB block mode and XTS block cipher mode, added in 2.11.0. The soVersion of mbedtls changed, bump PKG_RELEASE for packages that use mbedTLS This is to avoid having a mismatch between packages when upgrading. The size of mbedtls increased a little bit: ipkg for mips_24kc before: 163.846 Bytes ipkg for mips_24kc after: 164.382 Bytes Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* mbedtls: cleanup config patchDaniel Engberg2018-07-071-35/+28
| | | | | | | Clean up patch, use "//" consistently. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Enable SD block devicesDaniel Engberg2018-07-071-0/+1
| | | | | | | | USB storage support is however SCSI Disk block device support isn't meaning that connected devices wont enumerate. Enable CONFIG_BLK_DEV_SD by default to fix it. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* brcm2708: platform.sh: fix tar directory directiveAlexandru Ardelean2018-07-071-1/+1
| | | | | | | | BusyBox's `tar` command does not support the `--directory` directive, which is essentially `-C` in short-form option. BusyBox's `tar` command supports `-C`. Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* libconfig: update to version 1.7.2Enrico Mioso2018-07-071-4/+4
| | | | | | | | | The previous link did not work here. Compile-tested on: bcm47xx Runtime-tested on: bcm47xx Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
* kernel: remove DEVMEM and DEVKMEM from target's configLuis Araneda2018-07-075-8/+0
| | | | | | | | | These options are handled by generic configuration Targets that need these options should select KERNEL_DEVMEM and/or KERNEL_DEVKMEM options on OpenWRT's config Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* WDR4900v1 remove dt node for absent hw crypto.Tim Small2018-07-071-0/+24
| | | | | | | | | | | | | | | | | | The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the definition for the related P1010 SoC. However, the P1040 lacks the CAAM/SEC4 hardware crypto accelerator which the P1010 device tree defines. If left defined, this causes the CAAM drivers (if present) to attempt to use the non-existent device, making various crypto-related operations (e.g. macsec and ipsec) fail. This commit overrides the incorrect dt node definition in the included file. See also: - https://bugs.openwrt.org/index.php?do=details&task_id=1262 - https://community.nxp.com/thread/338432#comment-474107 Signed-off-by: Tim Small <tim@seoss.co.uk>
* ca-certificates: ca-bundle: add symlink for openssl default settingYousong Zhou2018-07-071-0/+2
| | | | | | | | | | OpenSSL defaults X509_CERT_FILE to /etc/ssl/cert.pem. This change is needed for wget-ssl and possibly others to work seamlessly with fresh ca-bundle installation Fixes openwrt/packages#6152 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kernel: usb: dwc2 DMA alignment fixesAntti Seppälä2018-07-072-0/+176
| | | | | | | | | | Add two patches submitted for upstream review that significantly improve the dwc2 driver on openwrt from kernel stability and performance perspectives. Fixes: FS#1367 Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
* linux: update license tag to use correct SPDX tagFlorian Eckert2018-07-071-1/+1
| | | | | | Use SPDX tag. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* toolchain/nasm: fix missing AR/RANLIB variablesFelix Fietkau2018-07-071-4/+5
| | | | | | Fixes build on macOS Signed-off-by: Felix Fietkau <nbd@nbd.name>
* perf: remove linux 4.4 workaroundsFelix Fietkau2018-07-074-75/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: remove linux 4.4 supportFelix Fietkau2018-07-07269-42118/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libubox: update to the latest versionFelix Fietkau2018-07-071-3/+3
| | | | | | 3c1b33b utils: add const_* byteswapping functions Signed-off-by: Felix Fietkau <nbd@nbd.name>
* firmware: amd64-microcode: update to 20180524Zoltan HERPAI2018-07-071-2/+2
| | | | | | | | | | | | | * New microcode update packages from AMD upstream: + New Microcodes: sig 0x00800f12, patch id 0x08001227, 2018-02-09 + Updated Microcodes: sig 0x00600f12, patch id 0x0600063e, 2018-02-07 sig 0x00600f20, patch id 0x06000852, 2018-02-06 * Adds Spectre v2 (CVE-2017-5715) microcode-based mitigation support, plus other unspecified fixes/updates. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* kmod-sched-cake: bump to latest 20180706Kevin Darbyshire-Bryant2018-07-071-3/+3
| | | | | | | Fixes a potential infinite loop bug when in unlimited (ie not using built in shaper) mode. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* tools/ccache: update to 3.4.2Hannu Nyman2018-07-062-5/+5
| | | | | | update version and refresh patch Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/cmake: update to 3.11.4Hannu Nyman2018-07-062-3/+3
| | | | | | Update cmake and refresh patches. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* toolchain: Replace YASM with NASMTed Hess2018-07-053-20/+13
| | | | | | | | | | Packages libx264 and ffmpeg are built with ASM options on x86 platforms. The current libx264 version no longer builds with YASM and requires NASM. ffmpeg 3.x can be built with either YASM or NASM however, furture 4.x versions will require NASM. Signed-off-by: Ted Hess <thess@kitschensync.net> Acked-by: Rosen Penev <rosenp@gmail.com>
* download.mk: enable DownloadMethod/github_archiveYousong Zhou2018-07-051-8/+14
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* scripts/dl_github_archive.py: rename from download.pyYousong Zhou2018-07-052-125/+130
| | | | | | | | | | | - Make the code more GitHub-specific - Requires mirror hash to work with .gitattributes - Use different API depending on whether PKG_SOURCE_VERSION is a complete commit id or other ref types like tags - Fix removing symbolic link - pre-clean dir_untar for possible leftovers from previous run Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* download.mk: add more commentsYousong Zhou2018-07-051-2/+5
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* fixup-makefile.pl: fixup when PKG_SOURCE is defined elsewhereYousong Zhou2018-07-051-1/+1
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* elfutils: bump to 0.173Luiz Angelo Daros de Luca2018-07-047-351/+149
| | | | | | | | | - Removed hacks to use standalone argp as upstream now detects it nicely. - As we are already installing files, use files from PKG_INSTALL_DIR and not PKG_BUILD_DIR - Only changes Makefile.am as PKG_FIXUP:=autoreconf is in use Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* kernel: bump 4.14 to 4.14.53Koen Vandeputte2018-07-045-13/+13
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.111Koen Vandeputte2018-07-045-8/+8
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: remove bs-partition ro-flag for UniFi AC devicesChristoph Krapp2018-07-041-1/+0
| | | | | | | | | | | | This removes the read-only flag from the bs (bootselect) partition on UniFi AC devices. This allows to correct the indicator from which partition the device is booting its kernel from. See also: - freifunk-gluon/gluon#1301 - https://bugs.lede-project.org/index.php?do=details&task_id=662 Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: swap TP-Link Archer C7 v2 USB port LED and GPIO namesAleksandr V. Piskunov2018-07-041-6/+6
| | | | | | | | | TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order, i.e. in order to match actual user visible labels, usb1 should be usb2, and vice versa. This patch swaps LED and GPIO power control node names. Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
* ath79: drop mv88e6063 switch driverMathias Kresin2018-07-041-289/+0
| | | | | | | | Due do a missing KCONFIG isn't selectable nor enabled in the target kernel config. Drop it for now and enable/add the driver at the time it is required. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: fix numbering for Netgear R7800 LAN portsAleksandr V. Piskunov2018-07-041-5/+5
| | | | | | | | | | Netgear R7800 switch LAN ports are numbered backwards in LuCI, i.e. numbering is not corresponding to the actual physical port labels, patch fixes that. Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com> [merged with existing board using the same config] Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ramips: add support for TL-WA801ND v5Romain MARIADASSOU2018-07-046-0/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MediaTek MT7628NN - CPU/Speed: 580 MHz - Flash-Chip: ELM Technology GD25Q64 - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn Currently the only method to install openwrt for the first time is via TFTP recovery. After first install you can use regular updates. Flash instructions: 1) To flash the recovery image, start a TFTP server with IP address 192.168.0.66 and serve the recovery image named tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS and Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds or until the lock LED is lighting up. It will try to download the recovery image and flash it. It can take up to 2-3 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 13:19:49 +0000