aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: Remove deprecated generic linux,part-probe patchHauke Mehrtens2018-12-157-189/+16
| | | | | | | This is now replaced by some other mtd partition parsing which was merged into upstream. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Make the patches apply on top of 4.19Hauke Mehrtens2018-12-15225-19291/+1181
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This makes the patches which were just copied in the previous commit apply on top of kernel 4.19. The patches in the backports-4.19 folder were checked if they are really in kernel 4.19 based on the title and only removed if they were found in the upstream kernel. The following additional patches form the pending folder went into upstream Linux 4.19: pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch Bigger changes were introduced to the m25p80 spi nor driver, as far as I saw it in the new code, it now has the functionality provided in this patch: pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch Part of this patch went upstream independent of OpenWrt: hack-4.19/220-gc_sections.patch This patch was reworked to match the changes done upstream. The MIPS DMA API changed a lot, this patch was rewritten to match the new DMA handling: pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch I did bigger manual changes to the following patches and I am not 100% sure if they are all correct: pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch pending-4.19/411-mtd-partial_eraseblock_write.patch pending-4.19/600-netfilter_conntrack_flush.patch pending-4.19/611-netfilter_match_bypass_default_table.patch pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch hack-4.19/211-host_tools_portability.patch hack-4.19/221-module_exports.patch hack-4.19/321-powerpc_crtsavres_prereq.patch hack-4.19/902-debloat_proc.patch This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Copy patches from kernel 4.14 to 4.19Hauke Mehrtens2018-12-15250-0/+46473
| | | | | | | | This just copies the files from the kernel 4.14 specific folders into the kernel 4.19 specific folder, no changes are done to the files in this commit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Move modifications of b53.h into patchHauke Mehrtens2018-12-154-36/+63
| | | | | | | | | | The b53 driver was added as a dsa driver into the mainline Linux kernel, but we still use the swconfig based driver. The header file b53.h is used by both drivers, but the swconfig one needs an extra member, add this one in a patch to not overwrite the version shipped with the mainline kernel. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Replace ledtrig-netdev with upstream backportHauke Mehrtens2018-12-158-616/+1179
| | | | | | | | | | | The ledtrig-netdev was added to upstream Linux kernel 4.16, replace our own version with the patch based on the upstream version. This will remove the ledtrig-netdev support from kernel 3.18, because I not want to spend time on backporting it to 3.18. This will make it easier to use the upstream version with kernel 4.19, by just not applying this patch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Reorder configurationHauke Mehrtens2018-12-152-4/+4
| | | | | | | | | | | This reorders the generic kernel configuration files. This was done with the following commands: $ ./scripts/kconfig.pl '+' target/linux/generic/config-4.14 /dev/null > target/linux/generic/config-4.14-new $ mv target/linux/generic/config-4.14-new target/linux/generic/config-4.14 $ ./scripts/kconfig.pl '+' target/linux/generic/config-4.9 /dev/null > target/linux/generic/config-4.9-new $ mv target/linux/generic/config-4.9-new target/linux/generic/config-4.9 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* nghttp2: bump to 1.35.1Hans Dedecker2018-12-151-2/+2
| | | | | | | | 63843750 Update manual pages 27801e98 Bump up version number to 1.35.1 60e020a8 nghttpx: Fix broken trailing slash handling Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* dnsmasq: Fix dhcp-boot, dhcp-reply-delay and pxe-prompt regressionsKevin Darbyshire-Bryant2018-12-142-1/+41
| | | | | | | The above options were incorrectly changed to required tags. Make them optional again. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* glibc: update to latest 2.27 commit (BZ #23927)Hans Dedecker2018-12-141-2/+2
| | | | | | | | | | | | | | | f6d0e8c36f Fix rwlock stall with PREFER_WRITER_NONRECURSIVE_NP (bug 23861) 2794474c65 powerpc: Add missing CFI register information (bug #23614) d8ca7a0c71 Fix _dl_profile_fixup data-dependency issue (Bug 23690) f1e211096b inet/tst-if_index-long: New test case for CVE-2018-19591 [BZ #23927] 4e9f34e54f support: Implement <support/descriptors.h> to track file descriptors e75481a7a7 support: Close original descriptors in support_capture_subprocess 0f79dc0be3 support_quote_string: Do not use str parameter name 6b2dd53aa0 support: Implement support_quote_string 50477165b9 malloc: Add another test for tcache double free check. 4b246928bd malloc: tcache double free check Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: bump 4.14 to 4.14.88Koen Vandeputte2018-12-146-12/+12
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 180-usb-xhci-add-support-for-performing-fake-doorbell.patch Fixes CVE: - CVE-2018-14625 Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.145Koen Vandeputte2018-12-1410-15/+15
| | | | | | | | | | | | | Refreshed all patches. Fixes CVE: - CVE-2018-14625 Compile-tested on: brcm2708 Runtime-tested on: brcm2708 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 3.18 to 3.18.129Koen Vandeputte2018-12-141-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: adm5120 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* iproute2: backport patch fixing incorrect usage of LDFLAGSHans Dedecker2018-12-142-1/+36
| | | | | | | Backport upstream patch fixing incorrect passing of -lxtables to LDFLAGS instead of LDLIBS in the tc/Makefile Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: update to latest git HEADHans Dedecker2018-12-131-3/+3
| | | | | | 1ac1c78 system-linux: get rid of SIOCSDEVPRIVATE Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mac80211: Update to version 4.19.7-1Hauke Mehrtens2018-12-1322-236/+52
| | | | | | | | | | | This updates the backports package used in mac80211 to version 4.19.7-1 which is based on kernel 4.19.7. This integrates all the stable fixes introduces in this kernel version. The deleted patches are not needed any more because they are either included in the upstream Linux kernel 4.19.7 or in backports 4.19.7-1. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: drop unneeded LINUX_VERSION_CODE checksRafał Miłecki2018-12-135-28/+0
| | | | | | | All those parsers are used by 4.14 targets. They don't need that backward compatibility code. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add DT binding support to the LZMA and WRG parsersRafał Miłecki2018-12-132-0/+14
| | | | | | It allows specifying those parsers directly in the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: mt7621: disable CONFIG_MTD_SPLIT_FIRMWARERafał Miłecki2018-12-131-1/+0
| | | | | | | It's no longer needed as all mt7621 devices use DT binding (supported by upstream mtd code) for specifying "firmware" part format explicitly. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: mt7621: specify "firmware" partition format for remaining devicesRafał Miłecki2018-12-134-0/+4
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kmod-dma-buf: fix build with external kernelStijn Tintel2018-12-121-1/+5
| | | | | | | | | | In hack/904-debloat_dma_buf.patch, DMA_SHARED_BUFFER is changed from bool to tristate. As this patch is not applied to external kernel sources, build fails if kmod-dma-buf is enabled. Fix this by only including the module file if CONFIG_EXTERNAL_KERNEL_TREE and CONFIG_KERNEL_GIT_CLONE_URI are not enabled. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq806x: fix and cleanup dts for NEC WG2600HPINAGAKI Hiroshi2018-12-121-290/+286
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit fixes and cleanups qcom-ipq8064-wg2600hp.dts to improve the support for WG2600HP. - Use dt label in qcom-ipq8064.dtsi: - gmac1 - gmac2 - gsbi4 - gsbi4_serial - gsbi5 - hs_phy_0 - ss_phy_0 - usb3_0 - usb3_1 - pcie0 - pcie1 - qcom_pinmux - Fix wrong pcie reset (perst) gpios - drop reset-gpio and use perst-gpios in qcom-ipq8064.dtsi - Remove unnecessary dt label from device dts - flash - phy0, phy4 - Rename spi-nor node to "flash" from "m25p80" - Fix qca,ar8327-initvals - use oem settings - fix: PAD0_MODE, PAD6_MODE - drop: PAD5_MODE (unnecessary) - Move mtd partitions under partitions (fixed-partitions) node - Specify "firmware" partition format - WG2600HP uses uImage format (denx,uimage) - Change failsafe status LED to power_red Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* openvpn: re-add option comp_lzoMartin Schiller2018-12-122-1/+2
| | | | | | | | This option is deprecated but needs to be kept for backward compatibility. [0] [0] https://community.openvpn.net/openvpn/wiki/DeprecatedOptions#a--comp-lzo Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* rpcd: update to latest Git headJo-Philipp Wich2018-12-121-3/+3
| | | | | | | | 3aa81d0 file: access exec timeout via daemon ops structure 7235f34 plugin: store pointer to exec timeout value in the ops structure ccd7c0a treewide: rename exec_timeout to rpc_exec_timeout Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* dnsmasq: fix ipv6 ipset bugKevin Darbyshire-Bryant2018-12-122-1/+22
| | | | | | | | | During upstream removal of conditional ipv6 support an order swap error was made in a ternary operator usage. This patch sent upstream. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* iproute2: backport upstream patch to fix print_0xhex on 32 bitHans Dedecker2018-12-121-0/+343
| | | | | | | | | The argument to print_0xhex is converted to unsigned long long so the format string give for normal printout has to be some variant of %llx. Backport the patch as otherwise, bogus values will be printed on 32 bit platforms. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath9k: register GPIO chip for OF targetsMathias Kresin2018-12-122-10/+19
| | | | | | | | | | | | | | | | | This partitialy reverts commit ccab68f2d399. Registering the GPIO chip without a parent device completely breaks the ath9k GPIOs for device tree targets. As long as boards using the devicetree don't have the gpio-controller property set for the ath9k node, the unloading of the driver works as expected. Register the GPIO chip with the ath9k device as parent only for OF targets to find a trade-off between the needs of driver developers and the broken LEDs and buttons seen by users. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix dtc compiler warningsMathias Kresin2018-12-123-7/+7
| | | | | | | | | | | | The qca9557/qca956x reset-controller aren't a simple bus. A simple bus would require node unit addresses. Add the node unit addresses for the qca9557 usb phys. Add the regs for the USB_PWRCTL and USB_CONFIG registers even not yet used. Fix the wrong ar7100 pcie controller node unit address as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop old image validation codeMathias Kresin2018-12-121-329/+1
| | | | | | | Due to the enforced image metadata we ensure that the correct image is uploaded. Checks based on a magic arn't required any more. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: enforce image metadata verificationMathias Kresin2018-12-121-0/+1
| | | | | | | Now that we got rid of all legacy images, we can enforce image metadata verification. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop support for ALLNET ALL0239-3G and Sitecom WL-341 v3Mathias Kresin2018-12-128-449/+0
| | | | | | | | | | | | Beside one exception, no one took care of these two remaining boards still using the legacy image build code during the last two years. Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken. The Sitecom WL-341 v3 image build code looks pretty hackish and broken. It's questionable if the legacy image works as all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use new image build code for D-Link DCS-930 familyMathias Kresin2018-12-124-73/+16
| | | | | | | | | | | | Drop the factory images and the firmware tool to create them. They don't work any more, since the factory image has an uImage header covering the whole kernel + rootfs. This way the uImage splitter will not be able to find the rootfs and the kernel will panic later on. The factory images were most likely added at a time the board had distinct partitions for kernel and rootfs. Signed-off-by: Mathias Kresin <dev@kresin.me>
* elfutils: install library files for pkg-configTony Ambardar2018-12-121-0/+3
| | | | | | | Support other packages using pkg-config to query existence and details of libelf and libdw libraries at build time. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* hostapd: add support for WPS pushbutton stationDaniel Golle2018-12-1210-14/+467
| | | | | | | | | | | | | | | | | | | | | | similar to hostapd, also add a ubus interface for wpa_supplicant which will allow handling WPS push-button just as it works for hostapd. In order to have wpa_supplicant running without any network configuration (so you can use it to retrieve credentials via WPS), configure wifi-iface in /etc/config/wireless: config wifi-iface 'default_radio0' option device 'radio0' option network 'wwan' option mode 'sta' option encryption 'wps' This section will automatically be edited if credentials have successfully been acquired via WPS. Size difference (mips_24kc): roughly +4kb for the 'full' variants of wpa_supplicant and wpad which do support WPS. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-fritz4040: update package to 2018-12-09Christian Lamparter2018-12-114-353/+5
| | | | | | | | | | | | | | | | | This patch updates the uboot-fritz4040 package to the latest version. The portability and private-libgcc patches, as well as the upload-to-f4040.sh script have been added to the upstream repository. Furthermore, the upload-to-f4040 has been updated to take the first parameter as the file it is supposed to flash, otherwise it defaults to the previous "uboot-fritz4040.bin". Furthermore the error messages have been improved and ftp will now dump some "progress information" to the user's console. Also included is support for gcc 8+ and a fix for the obnoxous error that currently breaks the builders: | fritz/src/lzma2eva.c:23:30: fatal error: zlib.h: No such file or directory Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* brcm63xx: HG655b: fix the imagetag at dtsDaniel Gonzalez Cabanelas2018-12-111-1/+1
| | | | | | | | | | | | | Fix the imagetag on the HG655b to allow a correct partition detection at boot time. It turns out that it was defined at the wrong partition. Just move the imagetag to the linux firmware partition. The bug is present since the 18.06 release. Without this fix, the board won't boot. Fixes: a27d59bb4274 ("brcm63xx: switch to new partition layout specification") Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: fix ethernet switch core reset mask for BCM6368Jonas Gorski2018-12-112-0/+52
| | | | | | | The reset mask for the bcm6368 switch core was left at 0 due to a copy & paste error. Fix this by setting it to the correct value. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: drop legacy profile for SR102Jonas Gorski2018-12-111-16/+0
| | | | | | | | | | | Remove the sky.mk causing a duplicate device profile to be added in image builder. The generic device code already generates a profile for the device. Fixes FS#1780. Fixes: d59126040701 ("brcm63xx: initial support for Sky SR102 router") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: add missing symbol in some 4.9 subtargetsKoen Vandeputte2018-12-113-0/+3
| | | | | | | Buildbot revealed some subtargets are still missing the new symbol. Fixes: dfbf836a52e4 ("kernel: bump 4.9 to 4.9.143") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.87Koen Vandeputte2018-12-104-34/+5
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0008-MIPS-ralink-Fix-mt7620-nd_sd-pinmux.patch Compile-tested: cns3xxx, imx6 Runtime-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.144Koen Vandeputte2018-12-103-49/+4
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 014-Kbuild-suppress-packed-not-aligned-warning-for-defau.patch Compile-tested: ar7, brcm2708 Runtime-tested: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.86Koen Vandeputte2018-12-1024-85/+74
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 180-usb-xhci-add-support-for-performing-fake-doorbell.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.143Koen Vandeputte2018-12-1016-40/+45
| | | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0063-Improve-__copy_to_user-and-__copy_from_user-performa.patch - 201-extra_optimization.patch New symbol: - CONFIG_HARDEN_BRANCH_PREDICTOR Compile-tested on: ar7, at91, brcm2708, ixp4xx, layerscape, orion Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [fix brcm2708/950-0149-Update-vfpmodule.c.patch] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 3.18 to 3.18.128Koen Vandeputte2018-12-104-22/+22
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 002-phy_drivers_backport.patch Compile-tested on: adm5120 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* dnsmasq: follow upstream dnsmasq pre-v2.81 v2Kevin Darbyshire-Bryant2018-12-1014-3/+4550
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport upstream commits. Most interesting 122392e which changes how SERVFAIL is handled especially in event of genuine server down/failure scenarios with multiple servers. a799ca0 also interesting in that answered received via TCP are now cached, DNSSEC typically using TCP meant until now answers weren't cached, hence reducing performance. 59e4703 Free config file values on parsing errors. 48d12f1 Remove the NO_FORK compile-time option, and support for uclinux. 122392e Revert 68f6312d4bae30b78daafcd6f51dc441b8685b1e 3a5a84c Fix Makefile lines generating UBUS linker config. 24b8760 Do not rely on dead code elimination, use array instead. Make options bits derived from size and count. Use size of option bits and last supported bit in computation. No new change would be required when new options are added. Just change OPT_LAST constant. 6f7812d Fix spurious AD flags in some DNS replies from local config. cbb5b17 Fix logging in cf5984367bc6a949e3803a576512c5a7bc48ebab cf59843 Don't forward *.bind/*.server queries upstream ee87504 Remove ability to compile without IPv6 support. a220545 Ensure that AD bit is reset on answers from --address=/<domain>/<address>. a799ca0 Impove cache behaviour for TCP connections. Along with an additional patch to fix compilation without DHCPv6, sent upstream. I've been running this for aaaages without obvious issue hence brave step of opening to wider openwrt community. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* Revert "dnsmasq: follow upstream dnsmasq pre-v2.81"Kevin Darbyshire-Bryant2018-12-1013-4523/+3
| | | | | | | | | | | | | This reverts commit a6a8fe0be5cd2edb1560bfc3f3094c3d34f2d2b0. buildbot found an error option.c: In function 'dhcp_context_free': option.c:1042:15: error: 'struct dhcp_context' has no member named 'template_interface' free(ctx->template_interface); revert for the moment Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* dnsmasq: follow upstream dnsmasq pre-v2.81Kevin Darbyshire-Bryant2018-12-1013-3/+4523
| | | | | | | | | | | | | | | | | | | | | | | | | Backport upstream commits. Most interesting 122392e which changes how SERVFAIL is handled especially in event of genuine server down/failure scenarios with multiple servers. a799ca0 also interesting in that answered received via TCP are now cached, DNSSEC typically using TCP meant until now answers weren't cached, hence reducing performance. 59e4703 Free config file values on parsing errors. 48d12f1 Remove the NO_FORK compile-time option, and support for uclinux. 122392e Revert 68f6312d4bae30b78daafcd6f51dc441b8685b1e 3a5a84c Fix Makefile lines generating UBUS linker config. 24b8760 Do not rely on dead code elimination, use array instead. Make options bits derived from size and count. Use size of option bits and last supported bit in computation. No new change would be required when new options are added. Just change OPT_LAST constant. 6f7812d Fix spurious AD flags in some DNS replies from local config. cbb5b17 Fix logging in cf5984367bc6a949e3803a576512c5a7bc48ebab cf59843 Don't forward *.bind/*.server queries upstream ee87504 Remove ability to compile without IPv6 support. a220545 Ensure that AD bit is reset on answers from --address=/<domain>/<address>. a799ca0 Impove cache behaviour for TCP connections. I've been running this for aaaages without obvious issue hence brave step of opening to wider openwrt community. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* dnsmasq: drop dnssec timestamp file patchKevin Darbyshire-Bryant2018-12-102-48/+1
| | | | | | | | | | | | Openwrt no longer uses and has not used since 5acfe55d71 Jun 2016 the timestamp file (/etc/dnsmasq.time) method of resolving the dnssec/ntp dnslookup chicken/egg problem, having used signals from ntp since that change. Drop the 'dnssec-improve-timestamp-heuristic' patch since it is neither used nor sent upstream. One less thing to refresh & maintain. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* nettle: bump to 3.4.1Nikos Mavrogiannopoulos2018-12-091-2/+2
| | | | | | | | This is a security fix adding safer APIs for RSA use. Compile tested for: ar71xx Signed-off-by: Nikos Mavrogiannopoulos <nmav@gnutls.org>
* base-files: add sysupgrade -k to save list of pkgsLuiz Angelo Daros de Luca2018-12-091-1/+35
| | | | | | | | | | | | | | When '-k' is used, sysupgrade inserts into backup a new file /etc/backup/installed_packages.txt which contains pkgname and origin (rom, overlay, unknown) without touching rootfs. It's mainly used to reinstall all extra packages: # opkg update # grep "\toverlay" /etc/backup/installed_packages.txt | cut -f1 | xargs -r opkg install # rm /etc/backup/installed_packages.txt Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* base-files: add sysupgrade -o to save all overlay filesLuiz Angelo Daros de Luca2018-12-091-4/+48
| | | | | | | | | | | Add sysupgrade '-o' option in order to include all overlay files in backup, except for those that are from packages but including files listed in conffiles, sysupgrade.conf or /lib/upgrade/keep.d. With '-u' option, it will skip files equals to /rom and conffiles that were not changed. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 12:18:40 +0000