aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add MikroTik hAP ac2 supportRobert Marko2021-04-058-1/+316
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com>
* uboot-mediatek: bpi-r64: no longer force recovery on first-bootDaniel Golle2021-04-041-4/+4
| | | | | | | | Now that sdcard.gz image contains everything needed to boot straight into production image, no longer force booting into recovery image on first boot by removing the logic which implemented that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mt76: update to the latest versionFelix Fietkau2021-04-041-3/+3
| | | | | | | | | | | | | | | | 465dda65ee84 mt7615,mt7915: replace fw log 0-terminating code with wiphy info length limit 62b13f5352b8 mt76: mt7921: fix key set/delete issue 0ff3a336a8d8 mt7615,mt7915: fix a compiler warning 113ba8a81d54 mt76: mt7615: remove redundant dev_err call in mt7622_wmac_probe() be1ab3b9ae7c mt76: mt7921: fix typo in mt7921_pci_resume 4e22f0dc934b mt76: mt7915: fix txpower init for TSSI off chips e66a0b9b8d66 mt76: mt7615: always wake the device in mt7615_remove_interface 38f656768a90 mt76: mt7921: always wake the device in mt7921_remove_interface 6ee4770de083 mt76: mt7921: rework mt7921_mcu_debug_msg_event routine e578b4b8d56a mt76: mt7615: fix .add_beacon_offload() f8c6c7cbf10f mt76: mt7915: fix mt7915_mcu_add_beacon Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.10 to 5.10.27Kevin Darbyshire-Bryant2021-04-0321-60/+64
| | | | | | | | | | | | | | | | Use update_kernel to refresh all patches, required manual updates to: 610-netfilter_match_bypass_default_checks.patch 611-netfilter_match_bypass_default_table.patch 762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch 764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch Run-tested: x86_64 Nothing screamed out but any funny business with linux bridging should suspect this update first. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* netifd: update to Git version 2021-04-03Hauke Mehrtens2021-04-031-3/+3
| | | | | | | f8899b9 netifd: bridge: set default value for igmp_snoop 327da98 netifd: add possibility to switch off route config Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uclient: update to Git version 2021-04-03Hauke Mehrtens2021-04-031-3/+3
| | | | | | | 83efca2 tests: fix possibly longer start of HTTP server 64e00d6 uclient-fetch: document missing options Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: enable airtime policy for the -basic variantsRui Salvaterra2021-04-031-1/+1
| | | | | | | | | | | | | | Airtime policy configuration is extremely useful in multiple BSS scenarios. Since nowadays most people configure both private and guest networks (at least), it makes sense to enable it by default, except for the most limited of the variants. Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2): 543944 bytes (airtime policy disabled) 548040 bytes (airtime policy enabled) Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> Acked-by: Daniel Golle <daniel@makrotopia.org>
* realtek: rename partitions in Netgear DTSIStijn Segers2021-04-031-5/+5
| | | | | | | | | Switch the Netgear DTSI for the Realtek target from the OEM partition naming scheme to accepted OpenWrt naming practices. A quick git grep for 'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* zram-swap: bail out early if the kernel doesn't support swapRui Salvaterra2021-04-031-0/+5
| | | | | | | | Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need to check if the current kernel supports swap before trying to configure zram-swap, as opkg can't check for kernel dependencies. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* zram-swap: clean up the makefileRui Salvaterra2021-04-031-3/+9
| | | | | | | Break dependencies into separate lines, to improve the readability. Trim trailing whitespace. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* lantiq: add basic support for AVM FRITZ!Box 3390Andreas Böhler2021-04-036-1/+328
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a 5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq has access to the flash memory, the Atheros runs fully from RAM. Specifications -------------- - Lantiq 500 MHz - 128MiB RAM - 128MiB NAND - 256k Flash - AR9580 5GHz WiFi - AR9342 560 MHz - 64MiB RAM - AR9328 2.4GHz WiFi Remarks ------- This commit only adds support for the Lantiq side of things and prepares the drivers for communication with the Atheros SoC. Thus, only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via another target. Some kernel patches will be required to add support for the Atheros SoC. Installation ------------ Use the eva_ramboot.py script to boot the initramfs image. Then, transfer the sysupgrade image to the device and run sysupgrade to flash it to the NAND. Signed-off-by: Andreas Böhler <dev@aboehler.at> Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
* lantiq: VR9: fix gpio-hog by defining the GPIO rangesJoachim Cerny2021-04-031-0/+1
| | | | | | | | | | defined gpio-ranges according to Reference: https://github.com/torvalds/linux/blob/master/drivers/pinctrl/pinctrl-xway.c#L864 This change is needed by gpio-hog on Fritzbox 3390 thx to @abajk Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl Signed-off-by: Andreas Böhler <dev@aboehler.at> Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
* lantiq: use ActualNetDataRate for speed reportingJeroen Peelaerts2021-04-032-1/+6
| | | | | | | | | | | | | Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems Refer to ITU-T G.997.1 chapter 7.5.2.8 Independent whether retransmission is used or not in a given transmit direction: - In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating. - In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state. Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com> Reviewed-by: Andre Heider <a.heider@gmail.com>
* lantiq: enable G.INP retransmission countersJeroen Peelaerts2021-04-032-3/+7
| | | | | | | | | | | | | | | | This commit adds monitoring for a couple of DSL line features that are present in the lantiq firmware blobs. * G.INP ON/OFF * Trellis encoding ON/OFF * Virtaul Noise ON/OFF * Bitswap ON/OFF Difference in size for ltq-vdsl-app = 1k Difference in size for kmod-ltq-vdsl-vr9 < 1k Reviewed-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
* ramips: fix IMAGE_SIZE of HC5x6: fix image size of HC5x61Shiji Yang2021-04-031-3/+3
| | | | | | | | "firmware" partition size defined in the device tree file is 0xf70000, so the right IMAGE_SIZE is 15808k Fixes: df1e5d646345 ("ramips: fix partition layout of hiwifi hc5x61") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: Fix booting on MQmaker WiTi boardDaniel Engberg2021-04-031-0/+1
| | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ramips: Fix booting on MTC WR1201René van Dorst2021-04-031-0/+1
| | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: René van Dorst <opensource@vdorst.com>
* armvirt: add 5.10 testing kernelAleksander Jan Bajkowski2021-04-031-0/+1
| | | | | | | Add 5.10 as testing kernel. Builds successfully with CONFIG_ALL_KMODS=y enabled. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: refresh 5.10 configAleksander Jan Bajkowski2021-04-033-19/+20
| | | | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Some common symbols have been moved to target config. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: copy config files for 5.10Aleksander Jan Bajkowski2021-04-033-0/+391
| | | | | | Copy config and patches for 5.10. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: refresh 5.4 configAleksander Jan Bajkowski2021-04-033-203/+14
| | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* base-files: fix status display commandAlexander Egorenkov2021-04-031-1/+1
| | | | | | | | | | | | | | | | | | | | If service() is called w/o parameter then the status display for services with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances. root@OpenWrt:~# /etc/init.d/samba4 status running root@OpenWrt:~# /etc/init.d/wpad status running Before change: /etc/init.d/samba4 enabled stopped /etc/init.d/wpad enabled stopped After change: /etc/init.d/samba4 enabled running /etc/init.d/wpad enabled running Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
* iproute2: fix libbpf detection with NLS enabledTony Ambardar2021-04-032-1/+21
| | | | | | | | | | | | | | | | | Upstream iproute2 detects libbpf using a one-line $CC test-compile, which normally ignores LDFLAGS. With NLS enabled however, LDFLAGS includes an "rpath-link" linker option needed to resolve libintl.so. Its absence causes both the compile and libbpf detection to fail: ld: warning: libintl.so.8, needed by libbpf.so, not found (try using -rpath or -rpath-link) ld: libelf.so.1: undefined reference to `libintl_dgettext' collect2: error: ld returned 1 exit status Fix this by directly including $LDFLAGS in the test-compile command. Reported-by: Ian Cooper <iancooper@hotmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* binutils: fix libbfd missing DSO dependency if NLS enabledTony Ambardar2021-04-031-2/+4
| | | | | | | | | | | | | | | | | | | | | | | The libbfd package definition uses $(ICONV_DEPENDS) and $(INTL_DEPENDS) but links against neither, leading to libbfd detection failures in other packages (e.g. bpftools) and on-target relocation problems with libintl.so: root@OpenWrt:/# ldd /usr/lib/libbfd.so ldd (0x77db6000) libc.so => ldd (0x77db6000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77c6d000) Error relocating /usr/lib/libbfd.so: libintl_dgettext: symbol not found Add NLS-conditional linking of "libintl" to fix this. Also remove libbfd package dependency $(ICONV_DEPENDS) which is not used during building or linking. Tested with QEMU on malta/be32, after building all packages from binutils, bpftools and iproute2, using different libc options musl and glibc. Fixes: 08e817569630 ("binutils: use nls.mk to fix libbfd link errors in other packages") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* bpftools: drop unneeded libintl linking for NLSTony Ambardar2021-04-031-5/+1
| | | | | | | | There is no direct linking of libintl from bpftools, only secondary linking through libelf, so remove "-lintl" from TARGET_LDFLAGS. Fixes: 5582fbd6135f ("bpftools: support NLS, fix ppc build and update to 5.8.9") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel: bump 5.4 to 5.4.109John Audia2021-04-0257-182/+182
| | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: pending-5.4/611-netfilter_match_bypass_default_table.patch The upstream change affecting this patch is the revert of an earlier kernel commit. Therefore, we just revert our corresponding changes in [1]. Build system: x86_64 Build-tested: ipq806x/R7800 [1] 9b1b89229f0e ("kernel: bump 5.4 to 5.4.86") Signed-off-by: John Audia <graysky@archlinux.us> [adjust manually rebased patch, add explanation] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: enhance support for Linksys EA9500Vivek Unune2021-04-014-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add leds and configs 2. Add network configs 3. Add script to clear partial boot flag 4. Hack to use port 5 as cpu port as port 8 connected to eth2 wont pass any frames 5. Enable EA9500 image generation Hardware Info: - Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz - Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 - DDR3 RAM - 256 MB - Flash - 128 MB (Toshiba TC58BVG0S3HTA00) - 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) - 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch - Ports - 8 Ports, 1 WAN Ports - Antennas - 8 Antennas - Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1 Flashing Instructions: 1. Connect a USB-TTL table to J6 on the router as well as a ethernet cable to a lan port and your PC. 2. Power-on the router. 3. Use putty or a serial port program to view the terminal. Hit Ctrl+C and interrupt the CFE terminal terminal. 4. Setup a TFTP server on your local machine at setup you local IP to 192.168.1.2 5. Start the TFTP Server 6. Run following commands at the CFE terminal flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2 nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit 7. Reboot router to be presented by OpenWrt Note: Only installation method via serial cable is supported at the moment. The trx firmware has to be flashed to both the partitions using following commands from CFE prompt. This will cover US and Non-US variants. Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use upstream Linksys EA9500 fixesRafał Miłecki2021-04-012-1/+30
| | | | | | One fix was accepted, one was added. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firewall4: update to latest Git HEADJo-Philipp Wich2021-04-011-3/+3
| | | | | | | | | | | | | 29fba84 tests: expand testing 6bf82a8 fw4.uc: fix family test functions 25b2c7d fw4.uc: fix parsing boolean "0" values 694d428 rule.uc: fix redundant whitespace in rules without target 7f69fbb ruleset.uc: reduce empty lines in output 8f8e42c fw4.uc: gracefully handle missing defaults section 25287af treewide: remove ucode module preloading 802b685 fw4.uc: remove upvalue caching Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ucode: update to latest Git HEADJo-Philipp Wich2021-04-011-3/+3
| | | | | | | | 973cc6c compiler: actually expand block scope fix to for/while alt syntax 97bf297 compiler: ensure that alternative if/for/while syntax has own block scope f0e2a64 tests: add missing test case for fixed switch codegen Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uboot-mediatek: adapt root= cmdline arg for bpi-r64Daniel Golle2021-03-311-2/+2
| | | | | | Adapt to FIT partition parser changes. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: fix FIT partition parser compatibility issuesDaniel Golle2021-03-312-65/+18
| | | | | | | | | | | | The uImage.FIT partition parser used to squeeze in FIT partitions in the range where partition editor tools (fdisk and such) expect the regular partition. This is confusing people and tools when adding additional partitions on top of the partition used for OpenWrt's uImage.FIT. Instead of squeezing in the additional partitions, rather start with all uImage.FIT partitions at offset 64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm4908: backport DT patch adding Ethernet MAC addressRafał Miłecki2021-03-311-0/+82
| | | | | | | This tells OS (Linux) where from MAC should be read (bootloader MTD partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: mt7622: improve sysupgrade on MMCDaniel Golle2021-03-311-49/+12
| | | | | | | Use generic functions to acquire rootdev. Make sure to wipe rootfs_data in case of '-n'. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* base-files: functions: introduce new helper functionsDaniel Golle2021-03-312-63/+68
| | | | | | | | | | | Introduce cmdline_get_var() to /lib/function.sh and make use of it in export_rootdev() in /lib/upgrade/common.sh, making the code more simple and removing one level of indentation. Introduce get_partition_by_name() to /lib/upgrade/common.sh which is useful on non-EFI GPT platforms like mt7622. Remove some dead-code while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bmips: backport pinctrl fixesÁlvaro Fernández Rojas2021-03-312-0/+82
| | | | | | Backport some minor upstream fixes for the pinctrl drivers. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* netifd: update to git HEADDaniel Golle2021-03-311-3/+3
| | | | | | | | | | 09632d4 device: remove left-over comment b22f83d handler: add mechanism to generate external device handler stubs 80bf9d7 extdev: add support for external device handlers 44c0f40 system-linux: reorder sysctl functions c84f3b0 system-linux: add device options used by wpad Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7620: ralink-i2s: fix modpost errorIlya Lipnitskiy2021-03-311-1/+2
| | | | | | | | Fixes the following error when building without CONFIG_MODULE_STRIPPED: FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct of_device_id is not terminated with a NULL entry! Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips/mt7621: enable support for cpuidleRui Salvaterra2021-03-311-1/+9
| | | | | | | | | | | MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support deep sleep idle states and have a specific cpuidle driver for them. Enable support for it, while also switching from constant timer ticks to the idle dynticks model, with the TEO governor. Run-tested on a Redmi AC2100. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips/mt7621: drop the timer recalibration patchRui Salvaterra2021-03-313-97/+10
| | | | | | | | | | | | | | | | | We've been carrying this patch for many years [1], in order to fix a timer calibration issue on MT7621. Turns out, after retesting with a recent kernel (Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls or inconsistent BogoMIPS values across CPUs). Manually refreshed: 322-mt7621-fix-cpu-clk-add-clkdev.patch 323-mt7621-memory-detect.patch [1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Tested-by: Donald Hoskins <grommish@gmail.com> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips/mt7621: drop the weak reordering patchRui Salvaterra2021-03-312-12/+2
| | | | | | | | | | | | | | | | | | In order to fix random hangs on MT7621, we've been selecting WEAK_REORDERING_BEYOND_LLSC for years [1]. However, these random hangs have been most likely caused by an oversight in the MIPS implementation of the kernel memory consistency model, which has already been fixed for some time (and backported to stable) [2]. Manually refreshed: 321-mt7621-timer.patch [1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=5c971cd6fdd7298a2017bdb6bea870088eddb8b9 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/mips?h=linux-5.4.y&id=42344113ba7a1ed7b5654cd5270af0d5698d8521 Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Tested-by: Donald Hoskins <grommish@gmail.com> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* firewall: update to latest git HEADHans Dedecker2021-03-301-3/+3
| | | | | | | a4355a6 firewall3: clean up the flow table detection logic edd0dc5 firewall3: create a common helper to find strings in files Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ncurses: add screen-256color terminfoPaul Spooren2021-03-291-1/+2
| | | | | | | The terminfo is required by the popular terminal multiplexer screen and tmux, offer it by default as the size impact is minimal with 885 Bytes. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ncurses: split long line of supported terminfoPaul Spooren2021-03-291-1/+12
| | | | | | | The terminfo files were all in one row which is terrible to read. Split them over multiple lines to improve readability. Signed-off-by: Paul Spooren <mail@aparcar.org>
* sunxi: enable wifi module on Pine64 boardsZoltan HERPAI2021-03-292-0/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi module, carrying an RTL8723BS. The wifi part is connected via SDIO, the BT part is connected via UART. The BT part requires additional code changes in the drivers so we'll skip that until 5.10. Aside from a DTS patch to enable the wifi module, add the required packages into the device definitions. [ 8.996970] RTL8723BS: module init start [ 9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40 [ 9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40 [ 9.014785] pnetdev = 000000009bdd5000 [ 9.047780] RTL8723BS: rtw_ndev_init(wlan0) [ 9.053349] RTL8723BS: module init ret =0 root@OpenWrt:/# iw list Wiphy phy0 wiphy index: 0 max # scan SSIDs: 9 max scan IEs length: 2304 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * monitor Band 1: Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (no IR) * 2472 MHz [13] (20.0 dBm) (no IR) * 2484 MHz [14] (20.0 dBm) (no IR) Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sunxi: enable MUSB in A53 subtargetZoltan HERPAI2021-03-291-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | The Pine64(+) and the SoPine64 baseboard has two USB ports. One of these (the lower) is connected directly to a USB host, the other one's (upper) PHY is shared with the separate OTG controller. In order to get it working, MUSB support needs to be enabled. As there are other targets which compile MUSB support into the kernel and not package it into modules, the same is done here. [ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.364250] usb usb5: Product: MUSB HDRC host driver [ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd [ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto [ 1.379891] hub 5-0:1.0: USB hub found [ 1.383677] hub 5-0:1.0: 1 port detected [...] [ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00 [ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 697.477180] usb 1-1: Product: USB Flash Disk Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* bmips: dts: align LEDsÁlvaro Fernández Rojas2021-03-296-32/+45
| | | | | | Align all bmips devices LED configurations. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: backport accepted pinctrl patchesÁlvaro Fernández Rojas2021-03-2939-2892/+3446
| | | | | | | These patches have been accepted for linux v5.13. External interrupts not supported for now. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: vr-3032u: fix gpio keysÁlvaro Fernández Rojas2021-03-291-2/+2
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700-v2: fix gpio keysÁlvaro Fernández Rojas2021-03-291-9/+9
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 11:19:05 +0000