| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds an option to set the recovery flag of newer TP-Link MediaTek
boards and remove it after a successful write.
To make use of this feature, add the '-t' option to mtd-write.
The '-t' option takes the mtd partition containing the recovery flag
(usually 'romfile') as an argument. Make sure this partition is not
flagged as read-only!
Example:
> mtd -t romfile write owrt.bin firmware
This command writes the recovery-flag before it begins writing the image
to the firmware partition. After the image-write has been successful,
the recovery flag is removed.
This way, the TP-Link web-recovery is automatically enabled on an
unsucessful flash (e.g. power loss).
This option is only available if the mtd package is compiled for the
ramips target.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
| |
|
|
|
|
| |
Add a command to fix WRG headers, based on wrgg.c.
Signed-off-by: George Hopkins <george-hopkins@null.net>
|
| |
|
|
|
|
|
| |
Based on fixseama.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
|
| |
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
So far fixtrx was calculating checksum over amount of data matching
partition erase size. It was mostly a workaround of checksum problem
after changing anything in initial TRX content (e.g. formatting JFFS2).
Its main purpose was to make bootloader accept modified TRX. This didn't
provide much protection of flash data against corruption.
This new option lets caller request calculating checksum over a bigger
amount of data. It may be used e.g. to include whole kernel data for
checksum and hopefully make bootloader go info failsafe mode if
something goes wrong.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Recently TRX checking code was changed to detect Seama format and don't
abort whole writing operation because of it. This isn't a good long-term
solution. It's a poor idea to teach every format handler recognizing all
possible formats. Instead it should be handled in a generic code which
should run check depending on the detected format.
This will also allow further improvements like fixing formats other than
TRX after replacing JFFS2.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48639
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The u-boot boot counter was never reset after a successful boot,
which sometimes could make some variables become out of sync.
This patch adds support for the boot counter and enables
auto_recovery unconditionally.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46690
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
NAND flash is very likely to contain bad blocks.
Currently, mtd and therefore sysupgrade fails when it encounters a single bad block, potentially leaving an unbootable system.
This patch allows the mtd utility to skip bad blocks in NAND flash and complete sysupgrade successfully.
Patch by: Matthew Redfearn <matt.redfearn@nxp.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40021
|
|
|
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37007
|
