| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
| |
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA988x.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA9887.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9888.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9984.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA4019.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
This update automatically includes a new firmware for the QCA6174:
firmware-6.bin_WLAN.RM.4.4.1-00079-QCARMSWPZ-1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add sendopts config support allowing to add options in sent DHCPv6 packets.
Options can be configured as follows :
uci set network.wan6.sendopts="sntpservers:3001:3001::1,3001:3001::2 11:00000000000000000000006674692F 0x3e8:ABCDEF"
Based on a patch by Frank Andrieu <fandrieu@gmail.com>
See https://git.openwrt.org/?p=project/odhcp6c.git;a=commit;h=510aaf6d528210c5e8a6159f9b80b32615e88c5f
for a more detailed description.
Latest git changes :
1f93bd4 dhcpv6: rework option passthrough logic
a477e95 odhcp6c: rework userclass and vendorclass command handling
510aaf6 odhcp6c: add -x opt:val support
ab75be1 treewide: update copyrights to 2018
f3a4609 odhcp6c: let odhcp6c_add_state return a success/failure indication
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
| |
This PR adds optional fstrim support
Signed-off-by: Dirk Brenken <dev@brenken.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Obviously not all GPIO controller allow to change the direction. The issue
is around since the beginning of the script but only due to the recent
changes error messages are more visible.
Add a check if a change of the direction is supported by the GPIO
controller and fallback to setting only the value if not.
Fixes: FS#1271
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
| |
GPIOs are exported as active high to the sysfs, hence the logic need to be
inverted.
Fixes: e66c47fb14f5 ("base-files: gpio switch: set output value with
direction")
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
e7a63fb ubox: Remove unnecessary memset calls
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
| |
Fix wrong PKG_SOURCE_DATE introduced in e14cac0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
|
| |
5bae22e ubus/lua: pass notification name to callback
212ceb1 valgrind complained about these
d57907c fix invalid close() call
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
|
| |
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
It is no longer actively maintained and does not work well in many
configurations. Fully replaced by wpad-mesh
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
The package has been moved to the package feed repository to allow for
non-base dependencies such as Perl.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
| |
Unconditionally enable connmark support and tie it to the conntrack core
module to allow removing this kernel configuration dependency from the
xtables-addons package.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
| |
5a5e21b nl80211: skip event notifications in wpa_supplicant scan result reply
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Dnsmasq used SIGHUP to do too many things: 1) set dnssec time validation
enabled, 2) bump SOA zone serial, 3) clear dns cache, 4) reload hosts
files, 5) reload resolvers/servers files.
Many subsystems within LEDE can send SIGHUP to dnsmasq: 1) ntpd hotplug
(to indicate time is valid for dnssec) 2) odhcpd (to indicate a
new/removed host - typically DHCPv6 leases) 3) procd on interface state
changes 4) procd on system config state changes, 5) service reload.
If dnssec time validation is enabled before the system clock has been
set to a sensible time, name resolution will fail. Because name
resolution fails, ntpd is unable to resolve time server names to
addresses, so is unable to set time. Classic chicken/egg.
Since commits 23bba9cb330cd298739a16e350b0029ed9429eef (service reload) &
4f02285d8b4a66359a8fa46f22a3efde391b5419 (system config) make it more
likely a SIGHUP will be sent for events other than 'ntpd has set time'
it is more likely that an errant 'name resolution is failing for
everything' situation will be encountered.
Fortunately the upstream dnsmasq people agree and have moved 'check
dnssec timestamp enable' from SIGHUP handler to SIGINT.
Backport the upstream patch to use SIGINT.
ntpd hotplug script updated to use SIGINT.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some newer LTE modems, like the MC7455 or EC25-E do not support
"802.3" mode, and will stay in "raw-ip" regardless of the mode being
set.
In this case, the driver must be informed that it should handle all
packets in raw mode. [1]
This commit fixes connectivity issues for these devices.
Before:
[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending discover
udhcpc: sending discover
After:
[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending select for 100.66.245.226
udhcpc: lease of 100.66.245.226 obtained, lease time 7200
udhcpc: ifconfig wwan0 100.66.245.226 netmask 255.255.255.252 broadcast
+
udhcpc: setting default routers: 100.66.245.225
[1] https://lists.freedesktop.org/archives/libqmi-
devel/2017-January/002064.html
Tested on cns3xxx using a Sierra Wireless MC7455 LTE-A
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[bumped PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
| |
Instead of grepping for NETWORK after calling ipcalc.sh; pass ipcalc.sh as
argument to eval allowing to use $NETWORK to retrieve the IPv4 prefix
(ip4prefix).
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Backport patches that separate spectral scan support from general debugfs
support of ath9k/ath10k; this allows to remove the dependency on
KERNEL_RELAY from these driver packages even with debugfs enabled and
avoids the memory footprint of the relay buffers allocated by ath9k/ath10k
even when they aren't used at all.
The KERNEL_RELAY dependency is moved to a new config symbol that enables
spectral scan support in these drivers.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
| |
Build depends must refer to source packages rather than binary package
names.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
| |
This feature has been unused for years, and its scope is too limited to be
actually useful.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
|
| |
18090d9 overlay: fix compilation with glibc
2a9a6ea libfstools: optimize building directory string for glob
de6b026 libfstools: support file paths longer than 255 chars
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
|
|
|
|
|
|
|
| |
This restores the alphabetical sort that was present
before the renaming of boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
|
|
|
|
|
|
|
|
|
| |
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
| |
Commit 30f61a34b4cfd2c676fea4a919e089d6a77254e9 claimed to drop -d & -p
options. In reality only -d was dropped. Update command help text to
reflect that -d is no longer a supported option.
Fixes FS#1187
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
More important bug fix:
402f05c Use full-rate mtu_time in all tins. Fixes an issue where some
cake tins experienced excessive latency since 49776da (dynamically
adjust target)
Minor bug fixes:
31277c2 Avoid unsigned comparison against zero. Fix compiler warning,
no known impact.
8cf5278 ack_filter: fix TCP flag check. A very contrived case may have
lead to dropping a SYN packet that should not be dropped.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
|
|
|
|
|
|
|
| |
6a82659 Use flock() for --concurrent option
73c2371 ebtables: extensions: Constify option struct
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
| |
Silence fw3 warnings in omcproxy init script in case fw3 is not enabled
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
| |
Remove LEDE_GIT references in favor to the new name-agnostic
PROJECT_GIT variable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Certain DHCP servers push a gateway outside of the assigned interface subnet,
to support those situations, install a host route towards the gateway.
If Gateway and IP are served in same network, openwrt quagga cannot learn
routes (rip routes are not getting added, showing inactive) whereas
working fine when Gateway and IP are in different network.
Signed-off-by: Mogula Pranay <mogula.pranay@nxp.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
| |
Our netdevs are named dsl by default now, the rename via scripts isn't
required anymore.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
| |
br2684ctl starts automatically, set up reload triggers, which fire as soon
as a atm driver is loaded. No need to do the reload via the script.
The reload is only required as soon as we can reliable switch between atm
and ptm driver and need to be implemented in a race free way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
| |
Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.
It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathis Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
| |
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
| |
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
| |
It is sufficient to define this in AT91Bootstrap/Default as this is not
used for all.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
| |
The fixes following problems
1. changing prefix at91bootstrap to AT91bootstrap will fix the default
selection of at91bootstrap for the selected sama5 subtarget.
2. fixed missing default selection of sama5d4 nand flash for the
selected sama5d4 subtarget.
3. corrected at91bootstrap Title name.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
|