aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Senao Engenius EAP300 v2Michael Pratt2020-11-252-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-EAP300A Engenius EAP300 v2 is an indoor wireless access point with a 100/10-BaseT ethernet port, 2.4 GHz wireless, internal antennas, and 802.3af PoE. **Specification:** - AR9341 - 40 MHz reference clock - 16 MB FLASH MX25L12845EMI-10G - 64 MB RAM - UART at J1 (populated) - Ethernet port with POE - internal antennas - 3 LEDs, 1 button (power, eth, wlan) (reset) **MAC addresses:** phy0 *:d3 art 0x1002 (label) eth0 *:d4 art 0x0/0x6 **Installation:** - if you get Failsafe Mode from failed flash: only use it to flash Original firmware from Engenius or risk kernel loop or halt which requires serial cable Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fdf0000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** If you have a serial cable, see Serial Failsafe instructions *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will not work DO NOT downgrade to ar71xx this way, can cause kernel loop or halt The easiest way to return to the OEM software is the Failsafe image If you dont have a serial cable, you can ssh into openwrt and run `mtd -r erase fakeroot` Wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade **TFTP recovery** (unstable / not reliable): rename initramfs to 'vmlinux-art-ramdisk' make available on TFTP server at 192.168.1.101 power board while holding or pressing reset button repeatedly NOTE: for some Engenius boards TFTP is not reliable try setting MTU to 600 and try many times **Format of OEM firmware image:** The OEM software of EAP300 v2 is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel size to be no greater than 1536k and otherwise the factory.bin upgrade procedure would overwrite part of the kernel when writing rootfs. Signed-off-by: Michael Pratt <mcpratt@pm.me> [clarify MAC address section, bump PKG_RELEASE for uboot-envtools] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* libusb-compat: removeRosen Penev2020-11-252-239/+0
| | | | | | | No package in base relies on this library. This library will be moved to packages where it is needed. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* linux-firmware: brcm: use RPI 4B NVRAM fileÁlvaro Fernández Rojas2020-11-252-4/+2
| | | | | | Use the dedicated RPI 4B NVRAM file introduced in 20191215. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* cypress-nvram: add proper package conflictsÁlvaro Fernández Rojas2020-11-251-1/+9
| | | | | | There are linux firmware packages for all RPIs NVRAMs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* cypress-firmware: add proper package conflictsÁlvaro Fernández Rojas2020-11-251-1/+4
| | | | | | | There are linux firmwares packages for 43362, 43430 and 43455 which shouldn't be installed at the same time as Cypress firmwares. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath10k-ct-firmware: add conflicts and better providesKarel Kočí2020-11-251-11/+71
| | | | | | | | | | | | | This expands packages to define not only provides but also conflicts. These packages provides same files so they should specify conflicts. Second expansion is that *-ct-htt and *-ct-full-htt firmwares can also provide *-ct variant as that allows explicit dependency on CT variant with various firmware modifications. Signed-off-by: Karel Kočí <karel.koci@nic.cz> [Bump PKG_RELEASE and format PROVIDES/CONFLICTS] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* exfat: update to 5.10.1Rosen Penev2020-11-241-5/+4
| | | | | | | | | | | | | | | | | | | | | Remove tar hacks and use PKG_BUILD_DIR. Added missing URL. Changelog: d5eb2e1 exfat: remove useless check in exfat_move_file() 8cb2bc3 exfat: use i_blocksize() to get blocksize 4cd0435 exfat: fix misspellings using codespell tool 485d677 exfat: fix use of uninitialized spinlock on error path 03b3db6 exfat: remove 'rwoffset' in exfat_inode_info 90797eb exfat: replace memcpy with structure assignment d144149 exfat: remove useless directory scan in exfat_add_entry() fc67230 exfat: eliminate dead code in exfat_find() 7c25c64 exfat: fix pointer error checking bfea1fb exfat: retain 'VolumeFlags' properly Signed-off-by: Rosen Penev <rosenp@gmail.com>
* opkg: purge package from cache on hash mismatchPaul Spooren2020-11-241-4/+4
| | | | | | | | | | 61b3c62 opkg_verify_integrity: better logging and error conditions f73d42f download: purge cached packages that have incorrect checksum 1c1480e download: factor out the logic for building cache filenames 293b1ce libopkg: factor out checksum and size verification a786e25 download: remove compatibility with old cache naming scheme Signed-off-by: Paul Spooren <mail@aparcar.org>
* tcpdump: patch CVE-2020-8037Jan Pavlinec2020-11-252-1/+48
| | | | | | | | | This PR backports upstream fix for CVE-2020-8037. This fix is only relevant for tcpdump package, tcpdump-mini is not affeted by this issue. Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz> [added missing commit description] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath10k-ct: update to latest versionÁlvaro Fernández Rojas2020-11-245-22/+22
| | | | | | | | 1d28d17 ath10k-ct: Fix RSSI reporting for wave-1 firmware. 0c2949e ath10k-ct: fwcfg allows configuring dma-burst setting. 13319ff ath10k-ct: stable patches, debugfs crashdump, 5.8 driver Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* uqmi: set plmn only if necessaryMartin Schiller2020-11-242-8/+22
| | | | | | | | | | | | | | | | | Setting the plmn to '0' (auto) will implicitly lead to a (delayed) network re-registration, which could further lead to some timing related issues in the qmi proto handler. On the other hand, if you switch back from manual plmn selection to auto mode you have to set it to '0', because this setting is permanently "saved" in the wwan module. Conclusion: If plmn is configured, check if it's already set euqally in the module. If so, do nothing. Otherwise set it. Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: update email address of Tomasz Maciej NowakTomasz Maciej Nowak2020-11-241-2/+2
| | | | | | | | | | Replace my o2.pl email address. I'm still available at the old address. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [rephrase commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: add initial support for Globalscale ESPRESSObin-UltraVladimir Vid2020-11-232-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses the same Armada-3720 SoC with extended hardware support. - SoC: Armada-3720 - RAM: 1 GB DDR4 - Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC - Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE) - WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB) - 1x USB 2.0 port - 1x USB 3.0 port - 1x microSD slot - 1x mini-PCIe slot (USB [with nano-sim slot]) - 1x mini-USB debug UART - 1x RTC Clock and battery - 1x reset button - 1x power button - 4x LED (RGBY) - Optional 1x M.2 2280 slot ** Installation ** Copy dtb from build_dir to bin/ and run tftpserver there: $ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/ linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb bin/targets/mvebu/cortexa53/ $ in.tftpd -L -s bin/targets/mvebu/cortexa53/ Connect to the device UART via microUSB port on the back side and power on the device. Power on the device and hit any key to stop the autoboot. Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g: $ setenv serverip 192.168.1.10 # Host $ setenv ipaddr 192.168.1.15 # Device Ping server to confirm network is working: $ ping $serverip Using neta@30000 device host 192.168.1.15 is alive Tftpboot the firmware: $ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin $ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb Set the console and boot the image: $ setenv bootargs $console $ booti $kernel_addr_r - $fdt_addr_r Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz to /tmp dir on the device. Gunzip and dd the image: $ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz $ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync Reboot the device. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* hostapd: fix patch offsetLeon M. George2020-11-231-1/+1
| | | | | | | Fixes the offset of the patch added in 93bbd998aa696a ("hostapd: enter DFS state if no available channel is found"). Signed-off-by: Leon M. George <leon@georgemail.eu>
* layerscape: enable spi-uart in LS1012A-FRDMPawel Dembicki2020-11-232-1/+14
| | | | | | | | | This patch add missing support of SC16IS740 serial controller, installed on LS1012A-FRDM board. It was required to change RCW bits, because SPI was disabled by default. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: iio: add fxas21002c driver supportPawel Dembicki2020-11-231-0/+50
| | | | | | This patch adds kernel modules for Freescale FXAS21002C 3-axis gyro driver. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: make initramfs kernel fit packedPawel Dembicki2020-11-235-9/+5
| | | | | | | | This will make developing process easier, because dtb will be included into image. Not need to enable initramfs image by default. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* linux-firmware: update to 20201118John Audia2020-11-231-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git log --pretty=oneline --abbrev-commit 20201022..20201118 2ea8667 (tag: 20201118) rtlwifi: v88.2 firmware files for RTL8192CU e850cf3 Merge https://github.com/rjliao-qca/qca-btfw into main 65370db rtw88: RTL8822C: Update firmware to v9.9.4 e371b7c Revert "rtw88: RTL8822C: Update firmware to v9.9.4" 51d2c81 vpdma: Move firmware to ti directory d7a24c9 Merge branch 'master' of https://github.com/shahasit/video-linux-firmware into main 9ee1543 Merge branch 'master' of https://github.com/shahasit/bt-linux-firmware into main 3bcc4c1 amdgpu: update picasso VCN firmware b6b4542 amdgpu: update raven2 VCN firmware 79aa335 amdgpu: update raven VCN firmware c93834e rtw88: RTL8822C: Update firmware to v9.9.4 3ef6c93 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099A_281A b503c96 Merge branch 'ath10k-20201023' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware into main 463fdea QCA: Update Bluetooth firmware for QCA6390 8a46c32 qcom : updated venus firmware files for v5.4 d7793e5 QCA : Fixed BT SSR due to command timeout / IO fatal error d842d8c ath11k: QCA6390 hw2.0: add to WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 8fb1a6e ath11k: QCA6390 hw2.0: add board-2.bin 34cb5fc ath11k: IPQ8074 hw2.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 c0a8efd ath11k: IPQ8074 hw2.0: add board-2.bin ac7f5e9 ath11k: IPQ6018 hw1.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 2594e51 ath11k: IPQ6018 hw1.0: add board-2.bin d8f10d4 ath10k: QCA6174 hw3.0: add firmware-sdio-6.bin version WLAN.RMH.4.4.1-00077 6652297 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00131 36059aa ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00131 1e5629d ath10k: QCA6174 hw3.0: update board-2.bin e315d1a ath10k: QCA6174 hw3.0: update firmware-6.bin to WLAN.RM.4.4.1-00157-QCARMSWPZ-1 Signed-off-by: John Audia <graysky@archlinux.us>
* netifd: update to the latest versionFelix Fietkau2020-11-231-3/+3
| | | | | | | 213748a9bcd9 system-linux: implement full device present state management for force-external devices 3abe1fc87151 system-linux: add retry for adding member devices to a bridge Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: enable the epoll-based event loopRui Salvaterra2020-11-238-8/+8
| | | | | | Hostapd supports epoll() since 2014. Let's enable it for better performance. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* uhttpd: update to git HEADDaniel Golle2020-11-231-4/+4
| | | | | | f53a639 ubus: fix uhttpd crash Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2020-11-231-3/+3
| | | | | | | d4d78db uxc: also delete procd runtime state on 'delete' e935c0c jail: add 'debug' extern variable to preload_seccomp Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uqmi: update to git HEADDaniel Golle2020-11-221-4/+4
| | | | | | | 65796a6 nas: add --get-plmn 0a19b5b uqmi: add timeout parameter Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uqmi: set device-operating-mode to onlineFilip Moc2020-11-222-1/+4
| | | | | | | This is required for LTE module MR400 (in TL-MR6400 v4). Otherwise LTE module won't register to GSM network. Signed-off-by: Filip Moc <lede@moc6.cz>
* uqmi: add support for IPv4 autoconf from QMIFilip Moc2020-11-222-12/+39
| | | | | | | | | | | There already was an option for autoconfiguring IPv4 from QMI but this was removed by commit 3b9b963e6e08 ("uqmi: always use DHCP for IPv4"). DHCP does not work on MR400 LTE module (in TL-MR6400 v4) so let's readd support for IPv4 autoconf from QMI but this time allow to configure this for IPv4 and IPv6 independently and keep DHCP default on IPv4. Signed-off-by: Filip Moc <lede@moc6.cz>
* uqmi: wait forever registration if timeout set to 0Thomas Richard2020-11-221-2/+2
| | | | | | | | | | | Give possibility to wait forever the registration by setting timeout option to 0. No timeout can be useful if the interface starts whereas no network is available, because at the end of timeout the interface will be stopped and never restarted. Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
* Revert "refpolicy: add variant that builds modular policy"Daniel Golle2020-11-221-33/+2
| | | | | | | | | | This reverts commit 9eb9943f82e0b2d5e32ffe1c63f5a82caca5094d. Building the 'modular' variant requires 'semodule_package' from 'selinux-python' to be installed on the buildhost. Apart from that, this change also broke the monolithic refpolicy 'targeted' build. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2020-11-221-3/+3
| | | | | | | | | 04a2edd uxc: make force-delete kill container process be6da62 seccomp: silence 'unknown syscall' warnings b22e625 jail: cgroup hack: rewrite cgroup -> cgroup2 df7fa7b uxc: fix incomplete commit Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* netifd: update to the latest versionFelix Fietkau2020-11-211-3/+3
| | | | | | | | | 351d690f1a09 wireless: fix passing bridge name for vlan hotplug pass-through c1c2728946b5 config: initialize bridge and bridge vlans before other devices 5e18d5b9ccb1 interface: do not force link-ext hotplug interfaces to present by default 4544f026bb09 bridge-vlan: add support for defining aliases for vlan ids Signed-off-by: Felix Fietkau <nbd@nbd.name>
* base-files: generated named bridge-vlan sectionsJohn Crispin2020-11-191-7/+8
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* uboot-envtools: ath79: add support for ALFA Network Pi-WiFi4Piotr Dymacz2020-11-181-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* valgrind: Update to version 3.16.1Hauke Mehrtens2020-11-182-4/+4
| | | | | | | | | | | | No special changes, just get in sync with recent code. See here for the changelog: https://valgrind.org/docs/manual/dist.news.html The ipkg sizes changes as follows for mips 24kc : 3.15 : valgrind_3.15.0-2_mips_24kc.ipk 1450680 3.16.1 : valgrind_3.16.1-1_mips_24kc.ipk 1491954 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* strace: Update to version 5.9Hauke Mehrtens2020-11-181-2/+2
| | | | | | | | | | | | No special changes, just get in sync with recent code. See here for the changelog: https://github.com/strace/strace/releases/tag/v5.9 The ipkg sizes changes as follows for mips 24kc : 5.8 : strace_5.8-1_mips_24kc.ipk 271195 5.9 : strace_5.9-1_mips_24kc.ipk 278352 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iperf3: Update to version 3.9Hauke Mehrtens2020-11-181-2/+2
| | | | | | | | | | | | No special changes, just get in sync with recent code. See here for the changelog: http://software.es.net/iperf/news.html#iperf-3-9-released The ipkg sizes changes as follows for mips 24kc : 3.7 : iperf3_3.7-1_mips_24kc.ipk 39675 3.9 : iperf3_3.9-1_mips_24kc.ipk 41586 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ethtool: update to version 5.9Hans Dedecker2020-11-171-2/+2
| | | | | | | | The ipkg sizes changes as follows for mips 24kc : 5.8 : ethtool_5.8-1_mips_24kc.ipk 34930 5.9 : ethtool_5.9-1_mips_24kc.ipk 35241 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* base-files: fix backwards compatiblity of rc.common EXTRA_COMMANDSMatthias Schiffer2020-11-172-7/+8
| | | | | | | | | | | | | | Avoid needlessly breaking old initscripts that set EXTRA_COMMANDS. This will aid in debugging (as it simplifies reverting to an older version of a package) and unbreaks third-party feeds (and packages that maintain their OpenWrt initscripts as part of the software's repo instead of the OpenWrt feed like fastd). Without this, initscripts that set EXTRA_COMMANDS become completely unusable, as all default commands like start/stop cease working. Fixes: 1a69f50dc627 ("base-files: fix rc.common help alignment") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* hostapd: set validity interval for BSS TMRADavid Bauer2020-11-171-1/+1
| | | | | | | | | | | | This sets the validity interval for the BSS transition candidate list to the same value as the disassociation timer. Currently the value is always 0, which is the specification states is a reserved value. Also, wpa_supplicant and from the looks of it some Android implementations will outright ignore the candidate list in this case. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add support for static airtime policy configurationDobroslaw Kijowski2020-11-172-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add support for passing airtime_sta_weight into hostapd configuration. * Since that commit it is possible to configure station weights. Set higher value for larger airtime share, lower for smaller share. I have tested this functionality by modyfing /etc/config/wireless to: config wifi-device 'radio0' ... option airtime_mode '1' config wifi-iface 'default_radio0' ... list airtime_sta_weight '01:02:03:04:05:06 1024' Now, when the station associates with the access point it has been assigned a higher weight value. root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/stations/01\:02\:03\:04\:05\:06/airtime RX: 12656 us TX: 10617 us Weight: 1024 Deficit: VO: -2075 us VI: 256 us BE: -206 us BK: 256 us [MAC address has been changed into a dummy one.] Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
* hostapd: fix per-BSS airtime configurationDobroslaw Kijowski2020-11-172-1/+3
| | | | | | | | airtime_mode is always parsed as an empty string since it hasn't been added into hostapd_common_add_device_config function. Fixes: e289f183 ("hostapd: add support for per-BSS airtime configuration") Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
* hostapd: ubus: add get_status methodDavid Bauer2020-11-171-0/+40
| | | | | | | This adds a new get_status method to a hostapd interface, which provides information about the current interface status. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: add VHT capabilities to client listDavid Bauer2020-11-171-0/+71
| | | | | | | This adds parsed VHT capability information to the hostapd get_clients method. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: add driver information to client listDavid Bauer2020-11-171-0/+24
| | | | | | | | This adds information from mac80211 to hostapd get_client ubus function. This way, TX as well as RX status information as well as the signal can be determined. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: fix variable shadowingDavid Bauer2020-11-171-0/+2
| | | | | | Fixes commit 838b412cb527 ("hostapd: add interworking support") Signed-off-by: David Bauer <mail@david-bauer.net>
* umdns: convert seccomp filter rules to OCI formatDaniel Golle2020-11-172-31/+42
| | | | | | | procd-seccomp switched to OCI-compliant seccomp parser instead of our (legacy, OpenWrt-specific) format. Convert ruleset to new format. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: drop legacy seccomp support, switch to OCI parsersDaniel Golle2020-11-171-3/+3
| | | | | | | | d8f36f5 seccomp: specifying architectures is optional d352e6e seccomp: switch to new OCI compliant parser c110405 trace: switch to OCI seccomp JSON output Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* wireguard-tools: fix category/description in menuconfigAlberto Bursi2020-11-171-2/+11
| | | | | | | | | | | | | | | | | | | | | wireguard-tools is trying to import the menuconfig section from the wireguard package, but since it's not anymore in the same makefile this seems to fail and wireguard-tools ends up in "extra packages" category instead with other odds and ends. Same for the description, it's trying to import it from the wireguard package but it fails so it only shows the line written in this makefile. remove the broken imports and add manually the entries and description they were supposed to load Fixes: ea980fb9c6de ("wireguard: bump to 20191226") Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com> [fix trailing whitespaces, add Fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: remove mvsw61xx swconfig driverDENG Qingfang2020-11-161-14/+0
| | | | | | | All targets that used mvsw61xx have switched to upstream mv88e6xxx DSA driver, so it can be removed. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* odhcpd: update to latest git HEADHans Dedecker2020-11-151-4/+4
| | | | | | fb55e80 dhcpv6-ia : write statefile atomically Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* dropbear: update to 2.81Hans Dedecker2020-11-154-9/+7
| | | | | | | | Update dropbear to latest stable 2.81; for the changes see https://matt.ucc.asn.au/dropbear/CHANGES Refresh patches Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* wireguard-tools: drop the dependency on ip-{tiny,full}Rui Salvaterra2020-11-141-1/+1
| | | | | | | | | | | | BusyBox ip already provides the required functionality and is enabled by default in OpenWrt. This patch drops the ip dependency and makes the BusyBox ip required dependencies explicit, allowing for a significant image size reduction. openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin size: 4588354 bytes (with ip-tiny) 4457282 bytes (with BusyBox ip) Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 11:37:21 +0000