aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/apm821xx
Commit message (Collapse)AuthorAgeFilesLines
* apm821xx: wndr4700: restore sd-card media detectionChristian Lamparter2018-11-261-1/+1
| | | | | | | This was not converted to the new, dt-based board name. Fixes: e90dc8d2722 ("apm821xx: convert to device-tree board detection") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: shuffle helper scripts to the frontChristian Lamparter2018-11-261-83/+82
| | | | | | | In a patch for the ath79, Mathias Kresin mentioned that helper scripts should be in front of the device targets. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Netgear WNDAP620 and WNDAP660Christian Lamparter2018-11-269-1/+370
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WNDAP620 and WNDAP660, they are similar devices, but due to the LAN LED configuration, the switch setup and WIFI configuration each gets a different device target. Hardware Highlights WNDAP620: CPU: AMCC PowerPC APM82181 at 1000 MHz DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF CPU: AMCC PowerPC APM82181 at 1000 MHz FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE) Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes Hardware Highlights WNDAP660: CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks DRAM: 256 MB, 2 x 128 MiB DDR2 FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE) Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes Flashing requirements: - needs a tftp server at 192.168.1.10/serverip. - special 8P8C(aka RJ45)<->D-SUB9 Console Cable ("Cisco Console Cable"). Note: Both WNDAP6x0 have a MAX3232 transceivers, hence no need for any separate CMOS/TTL level shifters. External Antenna: The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations: = Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description ===== 1. | 1 / High | 0 / Low | Use the internal antennae (default) 2. | 0 / Low | 1 / High | Use the external antennae The external antennaes are only meant for the 2.4 GHz band. One-way Flashing instructions via u-boot: 0. connect the serial cable to the RJ45 Console Port Note: This requires a poper RS232 and not a TTL/USB adaptor. 1. power up the AP and interrupt the u-boot process at 'Hit any key to stop autoboot' 2. setup serverip and ipaddr env settings Enter the following commands into the u-boot shell # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.10 3. download the factory.img image to the AP Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img 4. verfiy image integrity Enter the following commands into the u-boot shell # crc32 $fileaddr $filesize If the calculated crc32 checksum does not match, go back to step 3. 5. flash the image Enter the following commands into the u-boot shell # nand erase 0x110000 0x1bd0000 # nand write ${kernel_addr_r} 0x110000 ${filesize} 6. setup uboot environment Enter the following commands into the u-boot shell # setenv bootargs # setenv fileaddr # setenv filesize # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0' # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}' # setenv bootcmd 'run owrt_boot' # saveenv 7. boot # run bootcmd Booting initramfs instructions via u-boot: Follow steps 0 - 2 from above. 3. boot initramfs Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin # run addtty # bootm ${kernel_addr_r} Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: import gpio-export DT code from lantiqChristian Lamparter2018-11-261-0/+169
| | | | | | This will come in handy for the Netgear WNDAP620's antennae mux. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MR24: add to uboot-envtoolsChristian Lamparter2018-11-261-1/+24
| | | | | | | | This patch adds the complicated u-boot environment access settings for to the MR24 target. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 4.14 to 4.14.78Koen Vandeputte2018-10-222-50/+2
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 050-net-emac-fix-fixed-link-setup-for-the-RTL8363SB-swit.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* apm821xx: add disk-activity triggers via DT.Christian Lamparter2018-10-203-5/+2
| | | | | | | | The WNDR4700 and the MBL have a dedicated HDD activity LED. This patch adds the default led triggers to the DTS and removes the entries in 01_leds. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: apm82181.dtsi overhaulChristian Lamparter2018-10-201-135/+139
| | | | | | | | | | | | | | | | | | | - order entries by mmio address where possible - switch to lower-case address values - comment on BSP u-boot behaviour in regards to what it edits and look for - annotate irq lines with the help of interrupt-names - remove deprecated "device_type" properties The pci and network device_type had to stay since they are required by the drivers and u-boot. the cpu and memory device_types will remain as well as they are still part of the DT Spec. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: force WNDR4700 console to 115200n8Christian Lamparter2018-10-201-1/+1
| | | | | | | | | | | | | | | | | | | With the upcoming 4.19 release, the serial console on the Netgear WNDR4700 would no longer work as it is never really set and always relied on the kernel's serial code not to change the baud rate. On the stock firmware, Netgear forced the console setting through a custom CONFIG_CMDLINE in their kernel to 115200. Normally, they should have done it in a different way and just passed the baudrate through a "console=..." kernel parameter via the bootargs in the "/chosen" dt node. But in their default u-boot bootcmd setting, they somehow forgot to add the "run addtty", so there's no easy way to pass the baudrate from u-boot to the kernel. So it has to be forced as otherwise it ends up as 9600 baud. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: set uart compatible to ns16750Christian Lamparter2018-10-201-6/+11
| | | | | | | The APM821XX/PPC460EX datasheet mentions: "Register compatibility with 16750 register set" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-163-3/+3
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.14 to 4.14.76Koen Vandeputte2018-10-162-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* apm821xx: net: emac: fix fixed-link setup for the RTL8363SB switchChristian Lamparter2018-09-292-1/+49
| | | | | | | | | | | On the Netgear WNDAP620, the emac ethernet isn't receiving nor xmitting any frames from/to the RTL8363SB (identifies itself as a RTL8367RB). This is caused by hardware not knowing the right forced link settings (speed, duplex, pause, etc.) settings. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix dtc compiler warnings for MX60(W) and MR24's dts filesChristian Lamparter2018-09-292-8/+7
| | | | | | | | | | | | | | | | This patch fixes some of the dtc warnings: MR24: "reg" property in [...]mdio/phy@1 has invalid length (4 bytes) Node [...]button@1 has a unit name, but no reg property Relying on default #address-cells value for [...]phy@1 Relying on default #size-cells value for [...]phy@1 MX60(W): Node [..]nand/all has a reg or ranges property, but no unit name Node [..]button@1 has a unit name, but no reg property Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: remove wd, mybooklive-duo leftoversChristian Lamparter2018-09-293-8/+4
| | | | | | | | | The unification of the My Book Live Single and duo image in commit 9b47aa93c76b ("apm821xx: unify My Book Live Single + Duo images") made the wd,mybooklive-duo obsolete in most places and can be removed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: replace 'linux, stdout-path' with 'stdout-path'Christian Lamparter2018-09-293-3/+3
| | | | | | | | | | | | | | | This follows a similar upstream patch by Rob Herring: |commit 78e5dfea84dc15d69940831b3981b3014d17222e |Author: Rob Herring <robh@kernel.org> |Date: Wed Feb 28 16:44:06 2018 -0600 | powerpc: dts: replace 'linux,stdout-path' with 'stdout-path' | | 'linux,stdout-path' has been deprecated for some time in favor of | 'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'. | Search and replace all the of occurrences with 'stdout-path'. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 4.14 to 4.14.72Koen Vandeputte2018-09-261-1/+1
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 203-MIPS-ath79-fix-restart.patch - 0013-MIPS-ath79-fix-system-restart.patch - 180-earlycon-initialize-port-uartclk-based-on-clock-frequency-property.patch - 181-earlycon-remove-hardcoded-port-uartclk-initialization-in-of_setup_earlycon. patch - 700-1-6-e1000e-Remove-Other-from-EIAC.patch - 700-2-6-Partial-revert-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - 700-3-6-e1000e-Fix-queue-interrupt-re-raising-in-Other-interrupt.patch - 700-4-6-e1000e-Avoid-missed-interrupts-following-ICR-read.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* apm821xx: MBL: load kernel/dtb from SATA 0:1 firstFreddy Leitner2018-08-291-3/+3
| | | | | | | | | | | | | | | | | | | | | | This remedies an issue with the MBL Duo if both disks are inserted and contain OpenWrt. kernel and dtb would be loaded from SATA 1:1 while rootfs (/dev/sda2) would be mounted on SATA 0:1. Such a mix&match would obviously only work if both OpenWrt versions/ builds are identical, and especially fail after sysupgrade upgraded the system disk on SATA 0:1. The fallback to SATA 1:1 needs to be kept for MBL Single (only has SATA 1:1) and MBL Duo with one disk inserted on SATA 1:1. To speed up booting in those cases, the unneccesarily doubled "sata init" will only be called once. (In theory it could be omitted completely since the on-flash boot script already initializes SATA to load the on-disk boot script.) Tested on MBL Duo (all possible combination of disks) and MBL Single Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Freddy Leitner <hello@square.wf>
* treewide: fix some cosmetic glitches in dts filesPaul Wassi2018-08-272-2/+0
| | | | | | | | | | | - fix single spaces hidden by a tab - replace indentation with spaces by tabs - make empty lines empty - drop trailing whitespace - drop unnecessary blank lines Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* treewide: fix upgrade led handlingMathias Kresin2018-08-161-2/+4
| | | | | | | | | | | | The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.59Stijn Tintel2018-07-319-126/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Drop patch that was superseded upstream: ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch Drop upstreamed patches: - apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch - apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch - ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch - brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch - generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch - generic/pending/900-gen_stats-fix-netlink-stats-padding.patch In 4.14.55, a patch was introduced that breaks ext4 images in some cases. The newly introduced patch backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch addresses this breakage. Fixes the following CVEs: - CVE-2018-10876 - CVE-2018-10877 - CVE-2018-10879 - CVE-2018-10880 - CVE-2018-10881 - CVE-2018-10882 - CVE-2018-10883 Compile-tested: ath79, octeon, x86/64 Runtime-tested: ath79, octeon, x86/64 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* apm821xx: clean up gpio-hogsChristian Lamparter2018-07-302-30/+31
| | | | | | | | | | | convert the usb and both sata port power related gpio-hogs to what they really are: fixed-regulators. The ethernet phy-reset gpio-hog is replaced by a proper upstream (4.15+) reset-gpios property in the mdio-node. So this will work eventually. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: split MBL's rootfs.img.gz into a sysupgrade and factory imageChristian Lamparter2018-07-301-2/+3
| | | | | | | | | | | | | | | @vahid-dan reported a issue with extracting the rpi images with Gnome's Archive Manager: "Ubuntu Archive Manager cannot extract the file and it just throws a general error message: "An error occurred while extracting files". <https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi> The MBL's rootfs.img.gz image is generated in much the same way. Hence this patch preemptively splits the rootfs.img.gz image into a sysupgrade and a factory image. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: build squashfs-rootfs images for the MBLChristian Lamparter2018-07-305-10/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for squashfs as the root filesystem. advantages: - migrate from a existing -ext4 installation and back with the sysupgrade utility - existing partition layout will not be lost during switch - slightly smaller image size as compared to the -ext4 image. disadvantages: - needs f2fs + tools. This is because fstools rootdisk.c decides based on the partition size (currently root partitions > 100 MiB) f2fs is used as the rootfs_data filesystem. - rootfs_data is placed into the rootfs partition after the squashfs. This makes it difficult for tools that expect a /dev/sda${X} device. It also makes it difficult for data recovery tools as they might not expect to find a embedded partition or will be slightly confused. ... or will not support f2fs. For people with existing build configurations: make sure to include mkf2fs and f2fsck packages into the image. Otherwise the new -squashfs image will only boot from the ram-overlay. Note: All overlay data (configurations/all installed packages/...) will be placed in inside the rootfs partition (i.e. /dev/sda2) just after the squashfs image. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: unify My Book Live Single + Duo imagesChristian Lamparter2018-07-194-246/+187
| | | | | | | | | | | | | | By takimata: "Come to think of it, an MBL Single board boots up just fine on an MBL Duo image, and the MBL Single board identifies completely identical to the MBL Duo (Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB). I wonder if there is any downside to just using the MBL Duo firmware on a MBL Single. I wonder if the two firmwares could even be unified." <https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: attempt to fix sata access freezesChristian Lamparter2018-07-161-0/+25
| | | | | | | | | | | The original vendor's driver programmed the dma controller's AHB HPROT values to enable bufferable, privileged mode. This along with the "same priorty for both channels" could very well fix the freezes that have been reported on the forum by @ticerex and @takimata. <https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix usb-otg on 4.14Christian Lamparter2018-07-161-1/+1
| | | | | | | Starting with 4.14, the "amcc,dwc-otg" needs to be used in order to get the usb-otg to work. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 4.14 to 4.14.48Stijn Tintel2018-06-052-4/+4
| | | | | | | | | | | | | | | | | | Remove upstreamed patches: generic/pending/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch generic/pending/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch generic/pending/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch lantiq/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch Update patches that no longer apply: generic/pending/811-pci_disable_usb_common_quirks.patch ath79/0009-MIPS-ath79-add-lots-of-missing-registers.patch Fixes CVE-2018-6412. Compile-tested: octeon, x86/64. Runtime-tested: octeon, x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-221-2/+0
| | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* apm821xx: backport and reassign crypto4xx patchesChristian Lamparter2018-05-1813-12/+1268
| | | | | | | | | | | | | | | | | | | | This patch backports several patches that went upstream into Herbert Xu's cryptodev-2.6 tree: crypto: Use zeroing memory allocator instead of allocator/memset crypto: crypto4xx - performance optimizations crypto: crypto4xx - convert to skcipher crypto: crypto4xx - avoid VLA use crypto: crypto4xx - add aes-ctr support crypto: crypto4xx - properly set IV after de- and encrypt crypto: crypto4xx - extend aead fallback checks crypto: crypto4xx - put temporary dst sg into request ctx The older, outstanding patches from 120-wxyz series have been upstreamed as well and therefore they have been reassigned to fit into the series. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: don't select swconfig for the MR24Christian Lamparter2018-05-181-1/+1
| | | | | | | | | | The swconfig package is part of the DEFAULT_PACKAGES list in the apm821xx's nand subtarget. It's enabled by default because the MX60(W) and WNDR4700 need it for their initramfs. However the package is not necessary for the MR24's sysupgrade image, as the MR24 does not have a switch. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 4.14 to 4.14.41Koen Vandeputte2018-05-182-4/+4
| | | | | | | | | | | | | | | | | | | | | Refreshed all patches Dropped upstreamed patches: 522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch 523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch 525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch 527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch updated patches: 524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch 030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718 Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* build: consolidate fake uImage header build commandsMathias Kresin2018-04-201-1/+1
| | | | | | | | | | | Merge the two existing functions and use a parameter for the type header field. It updates the syntax of the former mpc85xx fake ramdisk header command to be compatible with mkimage from u-boot 2018.03 and fixes the build error spotted by the build bot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* apm821xx: Force Ethernet PHYID on MX60/MX60WChristian Lamparter2018-04-131-1/+1
| | | | | | | | | | The MX60's uboot disables all the PHYs before starting linux. This causes the PHY/switch detection code to malfunction almost all of the time. To get around this, set a compatible flag to force PHYID. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* apm821xx: increase WNDR4700's dtb+kernel partition to 3.5 MiBChristian Lamparter2018-03-302-23/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch cleans and reworks the WNDR4700 dts to increase the now combined dtb+kernel partition to 3.5 MiB. This has become necessary due to the switch to GCC 7.3 and the ever increasing kernel binary size. The dtb+kernel partition was combined in order to finally fix the problem with out-of-sync device-trees. From now on, the kernel and device-tree will always be updated together. Upgrade Note: Existing installations will have to use the TFTP firmware recovery option in order to install the update. Affected users are advised to make a backup of their existing configuration prior to running sysupgrade: <https://openwrt.org/docs/guide-user/installation/generic.backup#backup_openwrt_configuration> Due to the repartitioning of the NAND, the generated backup should be placed on either the internal HDD, an attached USB-Stick or on another PC (externally). To manually trigger the firmware recovery, the reset button has to be pressed (and hold) during boot. U-boot will enter the "Upgrade Mode" and starts a tftpserver listening on 192.168.1.1 for a tftp client from one of the four LAN/Ethernet ports to connect and upload the new system: (enable tftp binary mode!). openwrt-apm821xx-nand-netgear_wndr4700-squashfs-factory.img Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: switch MR24's initramfs to multi-image methodChristian Lamparter2018-03-301-7/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The recent change to switch to gcc 7.3 broke the image generation code, as the kernel would no longer fit into KERNEL_SIZE. This patch fixes the issue by reworking the initramfs creation and packaging, which will get rid of the KERNEL_SIZE check in the process. This new initramfs can be loaded through the MR24 U-boot in the following way: => setenv ipaddr 192.168.1.1 => setenv bootargs console=ttyS0,$baudrate => tftpboot c00000 192.168.1.2:meraki_mr24-initramfs-kernel.bin [...] Load address: 0xc00000 Loading: ################################################ [...] done Bytes transferred = 5952544 (5ad420 hex) => bootm $fileaddr \## Booting kernel from Legacy Image at 00c00000 ... ... For more information and the latest flashing guide: please visit the OpenWrt Wiki Page for the MR24: <https://openwrt.org/toh/meraki/mr24#flashing> Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* Kernel: bump 4.14 to 4.14.29Stijn Segers2018-03-232-5/+5
| | | | | | | | | | | | Right patch version this time, sorry! * Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code. * Refreshed patches. Compile-tested: ramips/mt7621, x86/64 Run-tested: ramips/mt7621, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Rosen Penev <rosenp@gmail.com>
* apm821xx: nand remove obsolete kernel config symbolMathias Kresin2018-02-231-1/+0
| | | | | | | | | | | | | | | | | | The missing CONFIG_USB_XHCI_PCI dependency on CONFIG_USB_PCI of the µPD720201 xhci-pci(e) usb 3.0 chip used by the WNDR4700 was fixed with 6112abf186bf ("kernel: enable CONFIG_USB_PCI for PCI usb modules"). Commit c38fb585763f ("kernel: fix disabling common usb quirks on 4.14") finally fixed the following build error: drivers/usb/host/xhci-pci.c: In function 'xhci_pci_probe': drivers/usb/host/xhci-pci.c:749:6: error: implicit declaration of function 'usb_xhci_needs_pci_reset' [-Werror=implicit-function-declaration] if (usb_xhci_needs_pci_reset(dev)) { Hence the CONFIG_USB_PCI symbol isn't required any longer in target kernel config. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: move nand_do_upgrade call to platform_do_upgradeMathias Kresin2018-02-161-16/+5
| | | | | | | | | | Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated with 30f61a34b4cf ("base-files: always use staged sysupgrade"). Update the platform upgrade code to use platform_do_upgrade() for NAND images as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: remove obsolete sysupgrade watchdog killMathias Kresin2018-02-161-10/+0
| | | | | | | | | The watchdog kill command was meant for busybox watchdog. Busybox watchdog was replaced by the procd watchdog mid 2013 with commit df7ce9301a25 ("busybox: disable the watchdog utility by default"), which makes the kill command obsolete since quite some time. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.18Stijn Tintel2018-02-081-27/+0
| | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - apm821xx/010-crypto-gcm-add-GCM-IV-size-constant.patch - backport/040-crypto-fix-typo-in-KPP-dependency-of-CRYPTO_ECDH.patch Remove pending-4.14/650-pppoe_header_pad.patch, it is superseded by upstream commit d32e5740001972c1bb193dd60af02721d047a17e. Update patch that no longer applies: hack/204-module_strip.patch Compile-tested: octeon, x86/64. Runtime-tested: octeon, x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* build: replace uses of OpenWrt with $(VERSION_DIST)Felix Fietkau2018-02-051-1/+1
| | | | | | This makes the distribution name more configurable. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* apm821xx: remove kernel 4.9 supportChristian Lamparter2018-01-1214-2682/+0
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: switch to 4.14.x kernelChristian Lamparter2018-01-121-1/+1
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: backport crypto4xx patches from 4.15Christian Lamparter2018-01-1231-0/+4686
| | | | | | | This patch backports changes to crypto4xx in order to get the crypto4xx operational. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-30 09:01:15 +0000