aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: fix typo in platform_do_upgrade_compex()Rafał Miłecki2019-09-161-1/+1
| | | | | Fixes: 641f6b6c26cb ("treewide: use new procd sysupgrade $UPGRADE_BACKUP variable") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: sysupgrade: use $UPGRADE_BACKUP to check for backupRafał Miłecki2019-09-113-4/+4
| | | | | | | Now that $UPGRADE_BACKUP is set conditionally there is no need to check the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-053-4/+4
| | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: fix invalid UPGRADE_OPT_SAVE_CONFIG spellingsRafał Miłecki2019-09-053-4/+4
| | | | | | | That was a result of accidentally running "sed" twice on some files. Fixes: 5797fe84a3b5 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: replace remaining (not working now) $SAVE_CONFIG usesRafał Miłecki2019-09-053-4/+4
| | | | | | | This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG Fixes: b534ba961100 ("base-files: pass "save_config" option to the "sysupgrade" method") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: sysupgrade: accept ath79 combined-imageTomasz Maciej Nowak2019-09-011-1/+1
| | | | | | | | | | There is md5 sum of whole image embedded in combined-image header which is checked on sysupgrade. The check will fail for ath79 images which may have embedded metadata. This is because metadata are appended after the combined image is created. To allow smooth transition from ar71xx to ath79, strip metadata before calculating md5 sum for whole image. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* treewide: convert WiFi caldata size and offset to hexadecimalAdrian Schmutzler2019-08-142-51/+51
| | | | | | | | | | | | | | This changes size and offset set for WiFi caldata extraction and MAC address adjustment to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-cal-data in DTS files. Since dd cannot deal with hexadecimal notation, one has to convert back to decimal by simple $(($hexnum)). Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-145-23/+23
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: really fix Mikrotik board detectionKoen Vandeputte2019-08-011-0/+1
| | | | | | | | | | | | | | | | | commit e09da0169a08 ("ar71xx: fix Mikrotik board detection") was generated based on testing a rb-912 board, on which detection failed. Testing on more hardware shows something fun: machine : MikroTik RouterBOARD 922UAGS-5HPacD machine : Mikrotik RouterBOARD 912UAG-5HPnD Both lowercase and uppercase are used. So ensure we support both now .. Fixes: e09da0169a08 ("ar71xx: fix Mikrotik board detection") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix Mikrotik board detectionKoen Vandeputte2019-07-291-1/+1
| | | | | | | | | | | Fix a typo in the machine type being extracted from /proc/cpuinfo which causes all Mikrotik board to be undetected properly. This lead to sysupgrade issues and probably some others too. Fixes: acf2b6c8881b ("ar71xx: base-files: fix board detect on new MikroTik devices") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix WLAN LED names for Archer C7Tomislav Požega2019-07-251-2/+2
| | | | | | Update WLAN LED colour identifier for both interfaces on Archer C7 Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* ar71xx: fix system LED names on Archer C5/C7Tomislav Požega2019-07-251-2/+2
| | | | | | | Move system LED board definitions of Archer C5/C7 to reflect actual system LED colour used Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* treewide: sysupgrade: get rid of platform_nand_pre_upgrade()Rafał Miłecki2019-07-221-35/+38
| | | | | | | | | | | 1) nand_do_upgrade() is always called by a target code 2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade() It means there is no need for the platform_nand_pre_upgrade() callback at all. All code that was present there could bo moved & simplly called by a target right before the nand_do_upgrade(). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-172-11/+11
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: get rid of platform_pre_upgrade()Rafał Miłecki2019-07-161-27/+23
| | | | | | | | | | | The only step between platform_pre_upgrade() and platform_do_upgrade() is switching to ramdisk. It should be fine to "mtd erase firmware" from the later callback and get rid of the first one. This change wasn't tested on affected target but identical code logic was verified to work as expected on brcm47xx with initramfs firmware. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: base-files: fix board detect on new MikroTik devicesHenryk Heisig2019-06-171-147/+165
| | | | | | | | | | | | | | | | | | | Move all MikroTik devices to new function to increase script execution speed. Machine name in new version of MikroTik RouterBOARD devices add "RB" before model name: Old machine name: MikroTik RouterBOARD 951Ui-2nD New: MikroTik RouterBOARD RB951Ui-2nD So this patch should fix it for all currently supported MikroTik boards. Signed-off-by: Henryk Heisig <hyniu@o2.pl> [rebased,commit message facelift,script fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz> [spotted missing 922UAGS-5HPacD] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: set mib-poll-interval on devices with ar8xxx switchPetr Štetiar2019-05-201-0/+50
| | | | | | | | | | | | | | Commit "generic: ar8216: add mib_poll_interval switch attribute" sets mib-poll-interval as disabled by default (was set to 2s), so it makes switch LEDs trigger disfunctional on devices which don't have mib-poll-interval set. So this patch sets mib-poll-interval to 500ms on devices which are using ar8xxx switch LEDs trigger, as the same value was set for built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch"). Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ar71xx: Fix network setup for TP-Link Archer C25 v1Adrian Schmutzler2019-05-151-10/+10
| | | | | | | | | Network for the Archer C25 v1 is set up without switch for no obvious reason. The LED setup is even done switch-based. This patch changes network setup so a switch is created. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix failsafe interface for TL-WR940nv6Joachim Fünfer2019-05-051-0/+1
| | | | | | | | Switches failsafe mode interface from WAN to LAN ports. Tested on TL-WR940Nv6.0 and TL-WR940Nv6.1 Signed-off-by: Joachim Fünfer <joachim.fuenfer@stusta.net>
* ar71xx: mute script error in ar922x-led-fix scriptRosy Song2019-05-051-0/+3
| | | | | | | | | | | | This commit fixes following script error in syslog: cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory sh: add: unknown operand sh: add: unknown operand Signed-off-by: Rosy Song <rosysong@rosinson.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit subject and message tweaks]
* ar71xx: add support for Mikrotik RouterBOARD 2011UiAS-2HnD r2Koen Vandeputte2019-04-234-3/+11
| | | | | | This board got a new hardware revision, without any change in functionality. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: Correct MAC address for WAN interface of Archer C7 v5Adrian Schmutzler2019-04-081-0/+4
| | | | | | | | | | | This device shares the network config with v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Add support for Ubiquity Bullet M (XW)Petr Štetiar2019-04-085-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: Add support for TP-Link CPE210 v3Robert Marko2019-04-024-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Looks identical to the v2. This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Robert Marko <robimarko@gmail.com> [Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: ens202ext: Fix whitespace issuesPetr Štetiar2019-04-011-4/+4
| | | | | | | | I've missed leading whitespace issues in the original patch, so fixing it in this commit. Thanks to pepe2k for letting me know. Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: ens202ext: Fix VLAN switchMichael Pratt2019-03-311-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The target ENS202EXT was just recently added right before the stable release of Openwrt 18. It flashes fine, but the physical switch is almost impossible to use until you have a VLAN set up. Tested on two devices. The actual problem is that eth0 represents nothing for whatever reason. In other words, both WAN and LAN are running from eth1. There may be an underlying problem in the build, but for now, I assume that this is correct and that a VLAN switch is an appropriate fix. Also, it's virtually impossible to get the switch running right through LuCI. It is one thing to get a switch to appear, but attempting to configure it breaks the whole thing. The VLAN has to be set up perfectly, otherwise, interfaces will not start up, and one is forced to reset settings, OR, the new LuCI feature kicks in and reverses any steps. It is extremely difficult to determine which virtual ports correspond to which physical ethernet ports without being able to set up the switch in LuCI. Temporary Workaround: followed directions here [openwrt/luci#867](https://github.com/openwrt/luci/issues/867) Reviewed-by: Marty Plummer <hanetzer@startmail.com> Signed-off-by: Michael Pratt <mpratt51@gmail.com> [commit author fix, subject fix, message text wrap] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: add support for MikroTik RouterBOARD 922UAGS-5HPacDKoen Vandeputte2019-03-264-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 922UAGS-5HPacD with a built-in 802.11ac High-Power radio (31dBm). See https://mikrotik.com/product/RB922UAGS-5HPacD for more info. Specifications: - SoC: Qualcomm Atheros QCA9557 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9882 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V - SFP: 1x host - USB: 1x 2.0 type A - PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems) - SIM slot: 1x mini-SIM Working: - Board/system detection - NAND storage detection - PCIe - USB: Type A & mini PCIe - Wireless - Ethernet - LED's (excl. SFP and RSSI levels) - Reset button - Sysupgrade Not working: - SFP cage Installation: - Boot vmlinux-initramfs image via BOOTP/TFTP and then flash sysupgrade image using "sysupgrade -n" Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: Add support for Mikrotik RB SXT 2nD r3Xavier Douville2019-03-224-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE with a single 2.4 GHz radio and a 100 Mbps Ethernet port. The device similar to the SXT 2nD r2, but it has SPI NOR flash instead of NAND flash. Hardware -------- CPU: Atheros AR9344 (600 MHz) RAM: 64 MiB FLASH: 16 MiB SPI NOR W25Q128 ETH: 1x 100 Mbps Atheros AG71xx WiFi: 2T2R 802.11b/g/n (ath9k) Power: Passive PoE 8-30 V Installation instructions: 1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a DHCP+TFTP server. 2. Erase the "firmware" partition using the mtd command. This should no longer be required once this patch is merged. 3. Use sysupgrade to install to flash. The file openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin should be used. Signed-off-by: Xavier Douville <github@douville.org>
* ar71xx: Speed up mtd extraction in ar71xx.shAdrian Schmutzler2019-03-131-2/+2
| | | | | | | | Although the amount of data read here is smaller than for the caldata, there still might be some speed gain compared to reading bytewise. And there is no harm ... Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Speed up caldata/eeprom handlingAdrian Schmutzler2019-03-132-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Speed comparison @ TP-Link TL-WDR4300 (just manually) results in a time reduction by three orders of magnitude (99.9 %). > time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096 4096+0 records in 4096+0 records out real 0m 15.85s user 0m 0.06s sys 0m 13.28s > time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.02s user 0m 0.00s sys 0m 0.02s Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Change led trigger from usbdev to usbportDavid Santamaría Rogado2019-02-281-46/+46
| | | | | | | | | | | | | This patch changes all the legacy usbdev leds triggers to the use usbport. The problem is that the usbdev triggers get applied as usbport in sysfs but LuCI gets confused and is not able to show the configuration with usbdev. More information can be found in the PR: <https://github.com/openwrt/openwrt/pull/1819> Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [extended commit message]
* ar71xx: GL.iNet AR300M family: correct LED definitionsAndreas Ziegler2019-02-261-0/+1
| | | | | | | | remove USB as this is no LED but power control rename WiFi LED with correct color red (like in stock firmware) set middle LED to be used for LAN link/activity Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
* ar71xx: Fix 5 GHz MAC address for Archer C60 v2Adrian Schmutzler2019-02-171-1/+6
| | | | | | | | Looks like C60 v2 needs the MAC address to be calculated manually, while the C60 v1 gets it correctly without manual interference. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix TL-MR3220-v2 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+5
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: ubnt-(xm,xw): fix LED RSSI indicationLech Perczak2019-02-081-4/+5
| | | | | | | | | | | | | | | | | When mapping for RSSI LEDs was defined for interface wlan0 on Ubiquiti XM and XW family, it missed connection to actual interface. Therefore create the mapping to interface, so RSSI LEDs work without additional configuration, after starting rssileds service. Also add the required package for this. While at that, remove coefficients needed for PWM LEDs, as XM and XW boards do not support PWM LEDs. Tested-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [Squashed commits + remove custom device_packages + slighty rewrite the commit msg] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix RB941-2nD detectionJulien Rabier2019-02-081-1/+1
| | | | | | | | | | | | Some hAP lite routers aren't detected because /proc/cpuinfo shows "RouterBOARD RB941-2nD" instead of "RouterBOARD 941-2nD". Fix that. Signed-off-by: Julien Rabier <taziden@flexiden.org> [Alter string to include all flavours + slight rewrite of commit msg] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: use correct wan mac address for the TP-Link Archer C7 v4David Santamaría Rogado2019-01-301-7/+11
| | | | | | | | | | | | The correct MAC address for this device is lan_mac +1, there is no need to set lan_mac so use base_mac variable instead lan_mac. Based on this PR for ath79: https://github.com/openwrt/openwrt/pull/1726 Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> [fix alphabetical ordering, reword subject] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for UniFi-AC-Mesh-ProChristoph Krapp2018-11-261-5/+12
| | | | | | | | | | | | | | | | This adds the build option for UniFi AC Mesh Pro as well as model detection for it. The device is a hardware clone of the AC Pro. - SoC: QCA9563-AL3A (775Mhz) - RAM: 128MiB - Flash: 16MiB - dual firmware partitions! - LAN: 2x 1000M - POE+ - Wireless: 2.4G: QCA9563 5G: UniFi Chip, QCA988X compatible Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ar71xx: fix TP-Link Archer C7 v5 switch LEDsRinki Kumari2018-11-171-3/+15
| | | | Signed-off-by: Rinki Kumari <rinki13@gmail.com>
* ar71xx: add support for Gainstrong MiniBox V3.2Pau Escrich2018-11-154-0/+6
| | | | | | | | | | | | Adds MiniBox V3.2 ar71xx target (QCA99531 + QCA9887) Info: http://oolite.cn/minibox-v3-2-qca9531-qca9887-module-pin-specification.html Reference patch: http://oolite.cn/wp-content/uploads/2017/09/minibox_v3_cc15.05_20160325.patch Installation: Upload firmware to uboot via HTTP at 192.168.1.1 (press button for 5 seconds) Signed-off-by: Pau Escrich <p4u@dabax.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (daniel@makrotopia.org: rebased and fixed conflicts, fixed LED name, added ath10k eeprom)
* ar71xx: Create /var/lock directory in platform_do_upgrade_*Sven Eckelmann2018-10-072-16/+3
| | | | | | | | | | | | | | | | | | The sysupgrade_pre_upgrade hook was removed with 5e1b4c57ded7 ("base-files: drop fwtool_pre_upgrade") while there were still scripts using it: * target/linux/ar71xx/base-files/lib/upgrade/allnet.sh * target/linux/ar71xx/base-files/lib/upgrade/openmesh.sh * target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh Not running the hooks can either prevent a successful upgrade or brick the device because the fw_setenv program cannot be started correctly. Instead of adding this hook again, the directory /var/lock for fw_setenv can also just be created directly before fw_setenv is called. Fixes: 5e1b4c57ded7 ("base-files: drop fwtool_pre_upgrade") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ar71xx: Use sysupgrade's RAMFS_COPY_* for fw_(set|print)envSven Eckelmann2018-10-073-9/+6
| | | | | | | | | | | | The install_bin from /lib/upgrade/common.sh is no longer creating the symlinks when a secondary parameter is added. But the fw_setenv program was always copied this way to the ramdisk for the upgrade. Instead, this should be done using RAMFS_COPY_* like on all other platforms. Fixes: 438dcbfe74a6 ("base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ar71xx: add support for TP-LINK CPE510 V2.0Andrew Cameron2018-08-022-2/+22
| | | | | | | | Adds Support for the TP-LINK CPE510 V2.0 by TP-Link. The hardware is almost the same as the CPE510 V1.0 Follow the same processes as for the CPE510 V1.0 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ar71xx: define switch for rb-952ui-5ac2ndThibaut VARÈNE2018-07-301-2/+2
| | | | | | | QCA9533 built-in switch can be configured Tested-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: fix TL-WR1043N v5 port mappingJohn Crispin2018-07-301-1/+4
| | | | | | fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.") Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.Tim Thorpe2018-07-301-1/+1
| | | | | | Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing. Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
* ar71xx: add support for TP-Link Archer C59 v2Keith Maika2018-07-307-1/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* ar71xx:add support for E750G v8张鹏2018-07-305-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E750G v8 is based on Qualcomm QCA9344. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4G GHz (AR9344) - 2x 10/100 Mbps Ethernet (PoE support) - 2x 10/100/1000 Mbps Ethernet - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
* ar71xx:add support for E750A v4张鹏2018-07-304-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E750A v4 is based on Qualcomm QCA9344. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 5G GHz (AR9344) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 10:54:24 +0000