aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2Adrian Schmutzler2019-11-132-3/+2
| | | | | | | | | | | | | | | | | | | As discussed in 1d18a14a90c7 ("ath79: really fix TP-Link Archer C7 v2 MAC address"), stock firmware MAC address assignment is actually as follows: wlan0 (5GHz) : -1 wlan1 (2.4GHz) : 0 eth1 (LAN) : 0 eth0 (WAN) : 1 This has never been fixed for ar71xx, so let's do it now. Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned to basemac-1 before ... Fixes: FS#408 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix tl-wdr3320-v2 upgrade南浦月2019-11-081-1/+1
| | | | | | | | | Fix the error that tl-wdr3320-v2 can't upgrade firmware via web interface by using magic_ver="0200" for this device. Signed-off-by: 南浦月 <nanpuyue@gmail.com> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix bug in NBG6716 kernelpacking, add firmware partitionAndré Valentin2019-10-271-2/+3
| | | | | | | -Fix the kernel image generation (more robust) -Add a firmware partition table allowing easy upgrade to ath79 Signed-off-by: André Valentin <avalentin@marcant.net>
* ar71xx: add model detection for UniFi AC-LRAndreas Ziegler2019-10-232-0/+9
| | | | | | | | | | | | | | This commit adds correct model detection for UniFi AC-LR. Previously, said device was incorrectly detected as UniFi-AC-LITE/MESH. The Information about the device is stored at 0xC in the EEPROM partition. It corresponds to the sysid in /etc/board.info of the Ubiquiti stock firmware. Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [adjust naming style of target to existing ones] Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: improve support for TP-Link CPE510 v2Adrian Schmutzler2019-10-217-21/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") where the support for this device wasn't optimal. Device support for the CPE510v2 so far has been a hack to enable flashing with CPE510v1 images. Those even have different hardware (e.g. additional ethernet port). With this patch, we provide proper support for this device in ar71xx. Installation: - Flash factory image through stock firmware WEB UI or through TFTP - To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. - Rename factory image to recovery.bin - Stock TFTP server IP: 192.168.0.100 - Stock device TFTP address: 192.168.0.254 Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net> [Rebased onto revert commit, changed comments in mach-cpe510.c, changed commit title and description, fixed eth0 MAC address, removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: WNDR4300: fix WAN LED behaviourMichal Cieslakiewicz2019-10-211-2/+1
| | | | | | | | | Change WAN LED behaviour to be consistent with other Netgear routers running OpenWrt. Instead of link speed, use amber colour to indicate link status. Green LED should be used when Internet connection is up and running. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx: WNDR4300: use standard labels for buttonsMichal Cieslakiewicz2019-10-211-3/+3
| | | | | | | GPIO key labels have been changed to standard ones (rfkill, reset, wps). It does not affect button functionality. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx: remove unnecessary execute permission bitSungbo Eo2019-10-121-0/+0
| | | | | | .c files do not need to be executable. 644 is enough. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: bump 4.14 to 4.14.147Koen Vandeputte2019-10-082-15/+13
| | | | | | | | | | | | | Refreshed all patches. Altered patches: - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx) - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79) Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-0613-173/+173
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.145Koen Vandeputte2019-09-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.144Koen Vandeputte2019-09-205-20/+15
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 816-pcie-support-layerscape.patch Fixes: -CVE-2019-15030 Compile-tested on: cns3xxx, layerscape Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix typo in platform_do_upgrade_compex()Rafał Miłecki2019-09-161-1/+1
| | | | | Fixes: 641f6b6c26cb ("treewide: use new procd sysupgrade $UPGRADE_BACKUP variable") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: make IRQ fixes target specificKoen Vandeputte2019-09-141-0/+57
| | | | | | | | | | | | | Move the IRQ fix from generic to ar71xx specific. Other targets like ath79 have specific pathes to delete this code. This resulted in a build failure on ath79 While at it, wipe the 4.19 version, as ar71xx will never reach this. Fixes: 530f76708cef ("ar71xx: Fix potentially missed IRQ handling during dispatch") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix potential IRQ misses during dispatch for qca953xKoen Vandeputte2019-09-131-0/+27
| | | | | | | | | | | If both interrupts are set in the current implementation only the 1st will be handled and the 2nd will be skipped due to the "if else" condition. Fix this by using the same approach as done for QCA955x just below it. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Revert "ar71xx: use platform code for qca955x usb0 init"Koen Vandeputte2019-09-121-14/+0
| | | | | | | | | | | | | | | This reverts commit 5b98061bb1ac7e3affadda7b55c6f4ed4eb8268e. As Piotr Dymacz pointed out: In QCA MIPS based WiSOCs, for first USB interface, device/host mode can be selected _only_ in hardware see description of 57c641ba6e QCA955x and QCA9563, second USB can be switched to device mode in software (tested and confirmed on real hardware). Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: qca955x pci init/reset fixesTomislav Požega2019-09-111-0/+120
| | | | | | | | | | | | | | Current ar724x code does the reset only on single pci bus, and in case of qca9558 writes the wrong register (0x10 vs 0x0c). This change allows the reset of second pci bus, commonly used in Archer C7 devices, in case host controller is stuck in reset. If the resetting controller on boot can solve any other issue it can be enabled unconditionally by removing reset check before ar724x_pci_hw_init is called. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> [refreshed to apply cleanly] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: enable ddr wb flush on qca955xTomislav Požega2019-09-111-0/+49
| | | | | | | | Enable flushing of write buffers on qca955x. GPL code has 0x88 reg defined for PCI flush which is likely an error since the device freezes on boot. So use DS default value 0xA8 for PCI flush. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* ar71xx: use platform code for qca955x usb0 initTomislav Požega2019-09-111-0/+14
| | | | | | | Switch from ci_usb_setup to generic platform initialization of usb0 port. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* treewide: sysupgrade: use $UPGRADE_BACKUP to check for backupRafał Miłecki2019-09-113-4/+4
| | | | | | | Now that $UPGRADE_BACKUP is set conditionally there is no need to check the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-053-4/+4
| | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: fix invalid UPGRADE_OPT_SAVE_CONFIG spellingsRafał Miłecki2019-09-053-4/+4
| | | | | | | That was a result of accidentally running "sed" twice on some files. Fixes: 5797fe84a3b5 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: replace remaining (not working now) $SAVE_CONFIG usesRafał Miłecki2019-09-053-4/+4
| | | | | | | This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG Fixes: b534ba961100 ("base-files: pass "save_config" option to the "sysupgrade" method") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: sysupgrade: accept ath79 combined-imageTomasz Maciej Nowak2019-09-011-1/+1
| | | | | | | | | | There is md5 sum of whole image embedded in combined-image header which is checked on sysupgrade. The check will fail for ath79 images which may have embedded metadata. This is because metadata are appended after the combined image is created. To allow smooth transition from ar71xx to ath79, strip metadata before calculating md5 sum for whole image. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ar71xx: WNR2200: remove redundant GPIO for WLAN LEDMichal Cieslakiewicz2019-08-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | Without this patch, an extra entry appears for AR9287 GPIO that duplicates WLAN LED but in fact drives nothing: gpiochip1: GPIOs 502-511, ath9k-phy0: gpio-502 ( |netgear:blue:wlan ) out hi gpio-503 ( |netgear:amber:test ) out hi gpio-504 ( |netgear:green:power ) out lo gpio-505 ( |rfkill ) in hi gpio-507 ( |wps ) in hi gpio-508 ( |reset ) in hi gpio-510 ( |ath9k-phy0 ) out hi <===! The pin pointed above is default LED GPIO (8) for AR9287. For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN LED instead - but initialization code is missing that information. This fix calls ap9x_pci_setup_wmac_led_pin() function at device setup, forcing WLAN LED pin to be 0 and removing redundant entry. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx/ath79: ag71xx: dont fetch the same var againKoen Vandeputte2019-08-271-1/+1
| | | | | | | tx_size was just declared above and set to BIT(tx->order) Use the declaration instead, which could avoid a pointer deref Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ag71xx: use base address value directly from the sourceKoen Vandeputte2019-08-271-2/+2
| | | | | | This brings the code more inline with the ath79 flavour Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ag71xx: make use of managed dev API simplifying codeKoen Vandeputte2019-08-271-51/+34
| | | | | | | | | Backport of a4eef43a120d ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev") combined with the initial changes from John Crispin. Simplifies the code a lot by using the Managed dev API. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ag71xx: replace ag71xx_get_phy_if_mode_name with phy_modes()Koen Vandeputte2019-08-271-22/+1
| | | | | | Backport of f73b2d64ed56 ("ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ag71xx: pass correct device pointer to dmaKoen Vandeputte2019-08-271-7/+7
| | | | | | | | | Backport of 4eaa3626a821 ("ath79: ag71xx: pass correct device pointer to dma functions") While 4.14 does not contain the warnings, it still makes sense to use the proper pointers here. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx/ath79: ag71xx: get ring_mask consistentKoen Vandeputte2019-08-271-1/+1
| | | | | | | | | All other instances of this identical declaration fetch the value directly from the ring_order. Also do it here. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ag71xx: add missing register writesKoen Vandeputte2019-08-271-0/+5
| | | | | | These are added in ath79, but were not backported here Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* treewide: convert WiFi caldata size and offset to hexadecimalAdrian Schmutzler2019-08-142-51/+51
| | | | | | | | | | | | | | This changes size and offset set for WiFi caldata extraction and MAC address adjustment to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-cal-data in DTS files. Since dd cannot deal with hexadecimal notation, one has to convert back to decimal by simple $(($hexnum)). Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-145-23/+23
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: ag71xx: init rings with GFP_KERNELKoen Vandeputte2019-08-091-1/+1
| | | | | | | ar71xx got lost during final rebase .. Fixes: b417a0c48d63 ("ar71xx/ath79: ag71xx: init rings with GFP_KERNEL") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx/ath79: ag71xx: fix sleep in atomicKoen Vandeputte2019-08-091-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When enabling atomic-sleep-debugging options in the kernel, following splat is seen when disabling the interface (which happens on boot): [ 10.892878] eth0: link down [ 10.896788] BUG: sleeping function called from invalid context at net/core/dev.c:5563 [ 10.904730] in_atomic(): 1, irqs_disabled(): 1, pid: 425, name: ip [ 10.911004] 2 locks held by ip/425: [ 10.914539] #0: (rtnl_mutex){....}, at: [<80377474>] rtnetlink_rcv_msg+0x2d8/0x380 [ 10.922441] #1: (&(&ag->lock)->rlock){....}, at: [<80330158>] ag71xx_hw_disable+0x24/0x94 [ 10.930976] CPU: 0 PID: 425 Comm: ip Not tainted 4.14.136 #0 [ 10.936716] Stack : 805e0000 80589228 80557404 876998ec 80610000 80610000 87cdcafc 805b5327 [ 10.945233] 80551534 000001a9 8061386c 87699ccc 87cfb180 00000001 876998a0 84f70903 [ 10.953751] 00000000 00000000 80b00000 8769979c 6a7407fa 00000000 00000007 00000000 [ 10.962270] 000000b7 16d0954a 000000b6 00000000 80000000 87cb658c 87cb65b0 00000001 [ 10.970787] 8046f97c 87699ccc 87cfb180 87ff2810 00000003 802ce724 0806e098 80610000 [ 10.979306] ... [ 10.981797] Call Trace: [ 10.984287] [<8006cb0c>] show_stack+0x58/0x100 [ 10.988814] [<800aab34>] ___might_sleep+0x100/0x120 [ 10.993774] [<8035c434>] napi_disable+0x30/0xd8 [ 10.998377] [<80330198>] ag71xx_hw_disable+0x64/0x94 [ 11.003418] [<8033069c>] ag71xx_stop+0x24/0x38 [ 11.007959] [<80359e30>] __dev_close_many+0xcc/0x104 [ 11.013009] [<80362eac>] __dev_change_flags+0xc8/0x1ac [ 11.018227] [<80362fb8>] dev_change_flags+0x28/0x70 [ 11.023182] [<80376890>] do_setlink+0x31c/0x91c [ 11.027786] [<80379360>] rtnl_newlink+0x3ec/0x7f8 [ 11.032563] [<80377498>] rtnetlink_rcv_msg+0x2fc/0x380 [ 11.037799] [<8039a734>] netlink_rcv_skb+0xd4/0x178 [ 11.042754] [<80399d10>] netlink_unicast+0x168/0x250 [ 11.047796] [<8039a2d4>] netlink_sendmsg+0x3d8/0x434 [ 11.052841] [<8033f0e4>] ___sys_sendmsg+0x1dc/0x290 [ 11.057794] [<80340140>] __sys_sendmsg+0x54/0x84 [ 11.062495] [<8007212c>] syscall_common+0x34/0x58 This is caused by calling napi_disable() while holding the spinlock. Fix it by omitting the spinlock, which is not required here Extensively tested on GL-MiFi, RB-912 and RB-922 hardware Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* tplink-safeloader: increase kernel partition for CPE/WBSx10v1Adrian Schmutzler2019-08-071-1/+1
| | | | | | | | | | | | | This is a preparation for ath79 support of the CPE210/CPE510 v1. Kernel size is chosen equal to the latest update for CPE610 v1. This also updates the partition size in ar71xx target, so code remains consistent if someone looks up the device. Since CPE210, CPE510, WBS210 and WBS510 (all v1) share the same partition layout definition, and are on deprecated target anyway, this changes them all at once. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: wpj531: fix SIG1/RSS1 LED GPIOLeon M. George2019-08-041-1/+1
| | | | | | | | | | | | | | In commit 6c937df749c7 ("ar71xx: wpj531: fix GPIOs for LED") wrong GPIO 13 for SIG1/RSS1 LED was commited, the correct GPIO number for this LED is 12. It's listed in "Hardware Guide - wpj531 7A06 (02/07/2019)" as GPIO12/RSS1 on the LED header and same GPIO 12 is used in the vendor's SDK as well. Fixes: 6c937df749c7 ("ar71xx: wpj531: fix GPIOs for LED") Signed-off-by: Leon M. George <leon@georgemail.eu> [commit subject/message facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: fix HiveAP 121 PLL for 1000MDavid Bauer2019-08-011-1/+1
| | | | | | | | | | | | The Aerohive HiveAP 121 has the wrong PLL value set for Gigabit speeds, leading to packet-loss. 10M and 100M work fine. This commit sets the Gigabit Ethernet PLL value to the correct value, fixing packet loss. Confirmed with iperf and floodping. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: really fix Mikrotik board detectionKoen Vandeputte2019-08-011-0/+1
| | | | | | | | | | | | | | | | | commit e09da0169a08 ("ar71xx: fix Mikrotik board detection") was generated based on testing a rb-912 board, on which detection failed. Testing on more hardware shows something fun: machine : MikroTik RouterBOARD 922UAGS-5HPacD machine : Mikrotik RouterBOARD 912UAG-5HPnD Both lowercase and uppercase are used. So ensure we support both now .. Fixes: e09da0169a08 ("ar71xx: fix Mikrotik board detection") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix nand init issues on some rb2011 devicesKoen Vandeputte2019-07-311-1/+5
| | | | | | | | | | | | | | | | | | | | While flashing lots of RB2011 devices, I noticed that some of them refused to boot properly, failing over the NAND parameters. Checking in detail shows that some device seem to use another NAND flash which only support standard 2048-byte pages, without 512-byte subpage support. This commit disables usage of these small subpage completely. Advantages: - Both NAND's with(out) subpage support are working now - The nand speed increases a bit (measured roughly 1%) in typical usecases Disadvantages: - The maximum storage capacity decreases by ~0.2% as small changes can consume a full page (2048 bytes) now. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix Mikrotik board detectionKoen Vandeputte2019-07-291-1/+1
| | | | | | | | | | | Fix a typo in the machine type being extracted from /proc/cpuinfo which causes all Mikrotik board to be undetected properly. This lead to sysupgrade issues and probably some others too. Fixes: acf2b6c8881b ("ar71xx: base-files: fix board detect on new MikroTik devices") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix WLAN LED names for Archer C7Tomislav Požega2019-07-251-2/+2
| | | | | | Update WLAN LED colour identifier for both interfaces on Archer C7 Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* ar71xx: fix system LED names on Archer C5/C7Tomislav Požega2019-07-251-2/+2
| | | | | | | Move system LED board definitions of Archer C5/C7 to reflect actual system LED colour used Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* ar71xx: Archer C7 v1 LED names and RFKILL fixesTomislav Požega2019-07-251-10/+10
| | | | | | | | | | All leds on these boards are green. v1 has RFKILL GPIO 23 for production units (it had GPIO 13 only for test phase units, and these are rather very rare to find). As for the previous attempt to fix this and revert due to WDR boards have blue leds, it was wrong: WDR board does not use common setup (false). Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* ar71xx: update qca-usb-quirks patchTomislav Požega2019-07-251-1/+1
| | | | | | | Base address for USB0 has changed from 0x18116c94 on AR934X to 0x18116d94 on QCA9558. CP Typo remained for years here... Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* treewide: sysupgrade: get rid of platform_nand_pre_upgrade()Rafał Miłecki2019-07-221-35/+38
| | | | | | | | | | | 1) nand_do_upgrade() is always called by a target code 2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade() It means there is no need for the platform_nand_pre_upgrade() callback at all. All code that was present there could bo moved & simplly called by a target right before the nand_do_upgrade(). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-172-11/+11
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: get rid of platform_pre_upgrade()Rafał Miłecki2019-07-161-27/+23
| | | | | | | | | | | The only step between platform_pre_upgrade() and platform_do_upgrade() is switching to ramdisk. It should be fine to "mtd erase firmware" from the later callback and get rid of the first one. This change wasn't tested on affected target but identical code logic was verified to work as expected on brcm47xx with initramfs firmware. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: enable SGMII fixup on Mikrotik wAP ACEtienne Champetier2019-07-161-0/+16
| | | | | | | | | | | | | | | | fixes intermittent loss of connectivity on 1Gbit port, with log message: > 803x_aneg_done: SGMII link is not ok Thanks to David Bauer for pointing me in the right direction. I just had to figure out the right bus_id, which you find in this log: > ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=004dd074, driver=Atheros 8031 ethernet] Fixes FS#2236 Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com> [Wrapped commit message - Fixed whitespace erors] Signed-off-by: David Bauer <mail@david-bauer.net>