aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: base-files: cleanups in etc/diag.shPiotr Dymacz2016-10-041-120/+137
| | | | | | | | | This includes: - code style fixes - use of local 'board' variable in LED names, wherever possible Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: fix boards order in etc/board.d/02_networkPiotr Dymacz2016-10-041-231/+231
| | | | | | | | Keep everything in alphabetical order. Boards are ordered in two steps, first within/inside common configuration (case section), then sections, globally. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: cleanups in etc/board.d/02_networkPiotr Dymacz2016-10-041-300/+177
| | | | | | | | | | | This includes: - code style fixes - removal of huge comment (it should be in doc, not here) and some small ones - removal of redundant config for DR531/WPJ531 as the default is the same - merge of boards with exactly the same interfaces config Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: rework etc/board.d/02_networkPiotr Dymacz2016-10-041-533/+554
| | | | | | | | | | Convert etc/board.d/02_network in ar71xx target to the same shape as we have in ramips target. Split code into two new functions: - interface/s setup in ar71xx_setup_interfaces() - MAC/s setup in ar71xx_setup_macs() Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: update to v4.4.23Álvaro Fernández Rojas2016-09-301-1/+1
| | | | | | | Refresh patches for all targets that support kernel 4.4. compile/run-tested on brcm2708/bcm2710 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ar71xx: Do not use a hardcoded ath10k firmware mac addressMartin Blumenstingl2016-09-281-7/+10
| | | | | | | | | | | | | | | | | | | | | ar71xx has an init-script for special devices where the ath10k OTP calibration data is stored on the PCIe card's EEPROM (and thus can only be read by ath10k). Unfortunately the OTP data uses the default mac address (= all devices come with the same mac address, which leads to problems when you have multiple of these devices in the same network). To work around this the mac address is patched in the firmware during the first boot of the device. To prevent flash wear this was only done if the ath10k firmware matched a hardcoded md5sum. However, if the md5sum does not match this can mean that either the mac address was already patched (which is fine) - unfortunately it can also mean that the firmware version was updated without updating the hardcoded md5sum. Change the "was the mac address already patched" check to actually compare the mac address inside the ath10k firmware. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker GatewayChris Blake2016-09-2716-19/+293
| | | | | | | | | This patch adds support for Cisco's Z1. Detailed instructions for the flashing the device can be found in the OpenWrt wiki: <https://wiki.openwrt.org/toh/meraki/z1> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: clean up DEVICE_PACKAGES of legacy devicesMatthias Schiffer2016-09-261-43/+22
| | | | | | Remove arbitrary or redundant packages from DEVICE_PACKAGES. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add model detection for many Ubiquiti AirMax XM devicesNeal Oakey2016-09-241-0/+36
| | | | | | Signed-off-by: Neal Oakey <neal.oakey@bingo-ev.de> [Matthias Schiffer: minor adjustments] Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* treewide: remove bad local shell variable declarationsJo-Philipp Wich2016-09-241-2/+2
| | | | | | | Local variable declarations outside of functions are illegal since the Busybox update to v1.25.0, therfore remove them from the appropriate places. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: update kernel config symbolsPiotr Dymacz2016-09-191-6/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: mark U-Boot and radio calibration data partitions as read-onlyPiotr Dymacz2016-09-192-17/+17
| | | | | | | General convention is to keep U-Boot and radio calibration data (ART) mtd partitions marked as read-only. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: set region code of TP-Link TL-WDR3600/4300 to USMatthias Schiffer2016-09-151-0/+2
| | | | | | | | There are currently two stock firmwares for the TL-WDR3600/4300, a US and a universal version. Both allow installing images with US region code, so we don't need to provide multiple images. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: separate TP-Link TL-WDR3600/4300/4310 profilesMatthias Schiffer2016-09-151-9/+19
| | | | | | | | | Simplify modifying some of the images without affecting the others. While we're at it, also unify the profiles to use := syntax and add "v1" to the TL-WDR4300 name to make things more consistent. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: update kernel 4.4 to version 4.4.20Álvaro Fernández Rojas2016-09-153-3/+3
| | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on brcm2708 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* image: remove padding parameter from append-kernel/append-rootfsMathias Kresin2016-09-133-9/+9
| | | | | | | | | | | Using pad-to instead of passing the optional padding to append-kernel or append-rootfs. It could be that the value of a variable is passed. In case the variable is empty no error is thrown. Furthermore the purpose of the extra parameter is hard to get without reading the code. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: add KERNEL_SIZE to the default device varsMathias Kresin2016-09-132-3/+3
| | | | | This reverts commit ec37a565878fd79d4127cbb843c17ce3b8dc97c0 and fixes the underlying issue.
* kernel: Backport pending appended DTB handling patchesDaniel Gimpelevich2016-09-121-1/+1
| | | | | | | | | | Backport patches from upstream Linux kernel which are making the kernel stores the appended dtb not in the same resisters as defined in the UHI specification, use a separate variable on MIPS. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [some modifications] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: fix typo in image build codeMathias Kresin2016-09-112-3/+3
| | | | | | | | | The kernel size isn't passed to the append-kernel build step and the resulting image bricks the device. Fixes FS#168. Signed-off-by: Mathias Kresin <dev@kresin.me>
* cleanup ucidef_set_interface* usageMathias Kresin2016-09-101-2/+1
| | | | | | | | - quote the interface name - remove call of not existing function - remove the proto if it's the default proto Signed-off-by: Mathias Kresin <dev@kresin.me>
* use immediate set in target MakefilesMathias Kresin2016-09-101-1/+1
| | | | | | | | No functional change, it's just to have the same style everywhere. This way I don't need to use any regex magic to extract all subtargets for compile tests. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: fix ethernet driver fast reset issue causing tx timeoutsFelix Fietkau2016-09-031-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: generate US- and EU-specific images for the Archer C7 v2Matthias Schiffer2016-08-281-1/+3
| | | | | | | | | | | | TP-Link has started providing US- and EU-specific stock firmwares that only allow upgrading to firmwares with the same region code. Provide factory images for both these regions. To avoid confusing users outside these regions, we still provide a "universal" factory.bin without a region code, although flashing either of the US and EU images would work as well. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: disable flow control to the built-in switch on AR934xFelix Fietkau2016-08-251-1/+0
| | | | | | | It apparently causes a regression on some devices if the ethernet cable is plugged in while booting. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: switch to 24kcJonas Gorski2016-08-231-1/+1
| | | | | | | GCC treats 24kc and 34kc exactly the same and will generate identical code, so there is no need to tune to 34kc instead of 24kc. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: update kernel 4.4 to version 4.4.19Stijn Tintel2016-08-231-4/+4
| | | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on all targets that use kernel 4.4 and aren't marked broken. Runtime-tested on ar71xx, octeon and x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: add support for Zbtlink ZBT-WE1526Piotr Dymacz2016-08-1812-1/+191
| | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 650/400/200 MHz (CPU/DDR/AHB) - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - two external, non-detachable antennas - 8x LED, 1x button - UART header (pinout: VCC, RX, TX, GND) Flash instruction: Use sysupgrade in vendor firmare which is based on OpenWrt. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix profile name of Mercury MW4530RChuanhong Guo2016-08-152-2/+2
| | | | | | | | The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R. There is no such a device called TL-WDR4530. Also change MERCURY to Mercury in /lib/ar71xx.sh Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ar71xx: add missing LZO support select for routerboard devicesFelix Fietkau2016-08-041-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove useless minimal/ath5k profilesFelix Fietkau2016-08-022-34/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: Make wget2nand look for LEDE project firmware filesdiizzyy2016-07-261-2/+2
| | | | | | Make wget2nand aware of the new file names Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* image: add a helper variable for getting kernel/rootfs from within image ↵Felix Fietkau2016-07-313-8/+8
| | | | | | Build/* templates Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: rename sysupgrade-nand to sysupgrade-tarJo-Philipp Wich2016-07-291-1/+1
| | | | | | | Now that the "sysupgrade-nand" step is used by non-NAND targets as well, rename it to "sysupgrade-tar" to make it more generic. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: don't use D-Link DIR-505 status LED as ethernet indicatorMatthias Schiffer2016-07-281-4/+0
| | | | | | | | | The stock firmware uses the single LED as status indicator only. Using the same LED both for status and as ethernet indicator is uncommon, and has been confusing users who were using the device as a WLAN mesh node (so the LED was just off, as no ethernet was connected). Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add revision detection for D-Link DIR-505 A1/A2Matthias Schiffer2016-07-281-0/+10
| | | | | | The A1 image also works on the A2, correctly set AR71XX_MODEL in this case. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add a missing ;; to ar71xx.shJohn Crispin2016-07-241-0/+1
| | | | | | | | commit 42305ae24aa7 ("ar71xx: add support for gl-mifi") was missing a ;; breaking boot up Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: add support for gl-mifiZhao Gang2016-07-2410-0/+148
| | | | | | | This add initial support for gl-mifi. Product page: http://www.gl-inet.com/mifi/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: clean up legacy-devices.mkMatthias Schiffer2016-07-272-322/+407
| | | | | | | | | Several legacy images were not buildable because of missing profile definitions in legacy-devices.mk since MultiProfile was removed. Update legacy-devices.mk to provide all necessary profiles, and change ordering to match legacy.mk. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add ath10k firmware to profile defaults where ath10k is usedFelix Fietkau2016-07-224-33/+33
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add missing profile for the nand subtarget (FS#56)Felix Fietkau2016-07-211-0/+18
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix WNDR4300v1 / WNDR3700v4 build (FS#56)Felix Fietkau2016-07-211-3/+9
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix more image build code whitespace/tab issuesFelix Fietkau2016-07-211-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix tab vs whitespace issue in image building codeFelix Fietkau2016-07-211-180/+180
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove obsolete MultiProfile template codeFelix Fietkau2016-07-211-40/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix default network config of WZR-HP-G300NH and CR3000Jo-Philipp Wich2016-07-201-2/+2
| | | | | | | | | | | The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the lan interface to a vlan tagged device while the switch was set up in untagged mode, leading to broken lan side ethernet connectivity by default. Fix the issue by emitting untagged interfaces, consistent with the switch setting on the device. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for gl-ar300mZhao Gang2016-07-2011-0/+217
| | | | | | | This add initial support for gl-ar300m router. Product page: http://www.gl-inet.com/ar300m/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add software transmit timestamp supportStephen Walker2016-07-152-0/+3
| | | | | | Add software transmit timestamp and ethtool (-T) timestamp support Signed-off-by: Stephen Walker <stephendwalker+github@gmail.com>
* ar71xx: define wmac reset function for QCA955xFelix Fietkau2016-07-152-3/+85
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for jjPlus JWAP230Piotr Dymacz2016-07-1310-0/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 2x 10/100/1000 Mbps Ethernet - 128 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm - 3x MMCX connectors - power input: 802.3at PoE or wide range DC (36-57 V) - optional 802.3af PSE - 1x mini-PCIe connector with PCIe, USB buses and SIM slot - 1x mini-PCIe connector with PCIe bus - 1x USB type-A connector - 6x LED, 1x button (hardware reset) - RS232 (MAX3223) and (E)JTAG headers Default configuration: - WAN on eth1 (RJ45 near LEDs with PoE input) - LAN on eth0 (RJ45 near DC jack) - left top LED set to be status LED - all LEDs configurable form user space Flash instruction (do it under U-Boot, using RS232): 1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Wallys DR531Piotr Dymacz2016-07-1311-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 550/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm - 2x MMCX connectors - mini-PCIe connector with PCIe/USB buses and SIM slot - 7x LED, 1x button, 1x optional buzzer - UART, (E)JTAG and LED headers Default configuration: - WAN on eth1 (RJ45 near DC jack) - LAN on eth0 (RJ45 near button) - S4 LED set to be status LED - all LEDs configurable form user space - button configured for reset Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 13:49:50 +0000