| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
Increase the spi-max frequency to 50 MHz, similar to the DIR-842.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
[improve commit title, fix commit message alignment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The uart node is enabled on all devices except one (GL-USB150 *).
Thus, let's not have a few hundred nodes to enable it, but do not
disable it in the first place.
Where the majority of devices is using it, also move the serial0
alias to the DTSI.
*) Since GL-USB150 even defines serial0 alias, the missing uart
is probably just a mistake. Anyway, disable it for now so this
patch stays cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
| |
None of the spi drivers on ath79 uses the num-cs property.
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
| |
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.
[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
| |
|
|
|
|
|
|
| |
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
| |
The WPS button was mapped to the restart/reset. This patch
changes it to emit the KEY_WPS_BUTTON keycode so pressing
the WPS button does initiate WPS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").
Some measurements performed on TP-Link Archer C7-v5:
mib-type=0, mib-poll-interval=500ms (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.93 0.00 0.00 1.93 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
mib-type=0, mib-poll-interval=2s (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.14 0.00 0.00 1.14 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880
USB is supported on the PCB but not connected.
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or the u-boot
failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted. Otherwise the u-boot
will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the firmware
checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
upgrade the factory.bin through the u-boot failsafe interface and then goto
step 2.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
