| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Device specifications:
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash (mx25l12805d)
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 2
+ used as LAN interface
* 12-24V 1A DC
* external antennas
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Device specifications:
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash (mx25l12805d)
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 2
+ used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Because the bug described in FS#2428 has been fixed with bf2870c1d9e1
("kernel: fix mtd partition erase < parent_erasesize writes") these
devices can now safely do sysupgrade.
Restore sysupgrade support disabled in:
0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations
and ja76pf2")
cc5256a8bfa0 ("ath79: base-files: disable sysupgrade for routerstations
and ja76pf2")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[move Build block, remove check-size argument, wrap sysupgrade line,
make commit message easier to read]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Due to rebase of the base-files split patch after adding support
for the ZyXEL NBG6716, its base-files were added to the generic
subtarget, although the device belongs to the nand subtarget.
This moves the definitions to their proper locations.
Fixes: 0130022baec0 ("ath79: split base-files into subtargets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[improve commit message, rebase]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space (especially helpful for the tiny devices).
The only script remaining in parent base-files is
/etc/hotplug.d/ieee80211/00-wifi-migration, everything else is
moved/split.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (generic) 49135 B
split (generic) 48533 B (- 0.6 kiB)
split (tiny) 43337 B (- 5.7 kiB)
split (nand) 44423 B (- 4.6 kiB)
Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
