aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/image/nand.mk
Commit message (Collapse)AuthorAgeFilesLines
* ath79: Deactivate ZyXEL NBG6716 by defaultHauke Mehrtens2021-05-021-0/+1
| | | | | | | | The kernel image is too big now and the build fails. WARNING: Image file zyxel_nbg6716-kernel.bin is too big: 4205404 > 4194304 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: fix factory image generation for Netgear and Zyxel boardsPaul Fertser2021-02-141-2/+0
| | | | | | | | | | | | | The factory images need to embed specific IDs to pass verification with the OEM firmware (including TFTP recovery), so they need to be per-device variables. Fixes: ab1584a797ad ("ath79: netgear: trim down uImage customisations") Fixes: 459c8c9ef816 ("ath79: add support for ZyXEL NBG6616") Reported-by: Marcin Juszkiewicz <marcin-openwrt@juszkiewicz.com.pl> Signed-off-by: Paul Fertser <fercerpav@gmail.com> [minor commit message adjustments, sort DEVICE_VARS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: netgear: trim down uImage customisationsSander Vanheule2020-11-251-11/+9
| | | | | | | | | | Replace NETGEAR_KERNEL_MAGIC by UIMAGE_MAGIC to better match the variable's purpose. This allows to drop the custom Build/netgear-uImage. Signed-off-by: Sander Vanheule <sander@svanheule.net> [keep UIMAGE_MAGIC definitions even for default value] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79/nand: add support for Netgear WNDR4300TNDavy Hollevoet2020-08-061-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WNDR4300TN, marketed by Belgian ISP Telenet. The hardware is the same as the WNDR4300 v1, without the fifth ethernet port (WAN) and the USB port. The circuit board has the traces, but the components are missing. Specifications: * SoC: Atheros AR9344 * RAM: 128 MB * Flash: 128 MB NAND flash * WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz) * Ethernet: 4x 1000Base-T * LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS * UART: on board, to the right of the RF shield at the top of the board Installation: * Flashing through the OEM web interface: + Connect your computer to the router with an ethernet cable and browse to http://192.168.0.51/ + Log in with the default credentials are admin:password + Browse to Advanced > Administration > Firmware Upgrade in the Telenet interface + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img + Proceed with the firmware installation and give the device a few minutes to finish and reboot. * Flashing through TFTP: + Configure your wired client with a static IP in the 192.168.1.x range, e.g. 192.168.1.10 and netmask 255.255.255.0. + Power off the router. + Press and hold the RESET button (the factory reset button on the bottom of the device, with the gray circle around it, next to the Telenet logo) and turn the router on while keeping the button pressed. + The power LED will start flashing orange. You can release the button once it switches to flashing green. + Transfer the image over TFTP: $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img Signed-off-by: Davy Hollevoet <github@natox.be> [use DT label reference for adding LEDs in DTSI files] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for gl-e750Luochongjun2020-07-291-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The gl-e750 is a portable travel router that gives you safe access to the internet while traveling. Specifications: - SoC: Qualcomm Atheros AR9531 (650MHz) - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG) - Ethernet: 10/100: 1xLAN - Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac) - USB: 1x USB 2.0 port - Switch: 1x switch - Button: 1x reset button - OLED Screen: 128*64 px MAC addresses based on vendor firmware: LAN *:a0 art 0x0 2.4GHz *:a1 art 0x1002 5GHz *:a2 art calculated from art 0x0 + 2 Flash firmware: Since openwrt's kernel already exceeds 2MB, upgrading from the official version of GL-inet (v3.100) using the sysupgrade command will break the kernel image. Users who are using version 3.100 can only upgrade via uboot. The official guidance for GL-inet is as follows: https://docs.gl-inet.com/en/3/troubleshooting/debrick/ In the future, GL-inet will modify the firmware to support the sysupgrade command, so users will be able to upgrade directly with the sysupgrade command in future releases. OLED screen control: OLED controller is connected to QCA9531 through serial port, and can send instructions to OLED controller directly through serial port. Refer to the links below for a list of supported instructions: https://github.com/gl-inet/GL-E750-MCU-instruction Signed-off-by: Luochongjun <luochongjun@gl-inet.com> [fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: re-enable image generation for GL-AR750SDavid Bauer2020-07-221-11/+1
| | | | | | | | | | | | | | | | The bootloader only writes the first 2MB of the image to the NOR flash when installing the NAND factory image. The bootloader is capable of booting larger kernels as it boots from the memory mapped SPI flash. Disable the NAND factory image. The NAND can be bootstrapped by writing the NAND initramfs image using the NOR upgrade method in the bootloader web-recovery and sysupgrading from there. The NOR variant is not affected. Also refactor the partition definitions in the DTS to make them less annoying to read. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: nand: disable images for glinet_gl-ar750sPetr Štetiar2020-07-071-0/+2
| | | | | | | | | Fixes following build failures: WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for 8devices Rambutan boardAndrey Bondar2020-07-071-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rambutan is a Wifi module based on QCA9550/9557 http://www.8devices.com/products/rambutan Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of DDR2 RAM - 128 MB of NAND Flash - 1x 100Mbps Ethernet - 1x 1000Mbps Ethernet (PHY on dev-kit) - 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz - 2x U.FL connectors on module, chip antennas on dev-kit - 1x miniPCIe slot - 2x USB2.0 host - 2x UART - SPI, I2C, GPIO Flash instructions: Upgrade from ar71xx target: sysupgrade -F /tmp/openwrt-ath79-nand-8dev_rambutan-squashfs-sysupgrade.tar or upgrade from GUI (don't save config) Use factory image to flash from U-Boot: tftpboot 80060000 openwrt-ath79-nand-8dev_rambutan-squashfs-factory.ubi nand erase.part ubi nand write 80060000 ubi ${filesize} Signed-off-by: Petr Štetiar <ynezz@true.cz> [copy&pasted missing commit description] Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
* ath79/nand: add support for Netgear WNDR4300SWStijn Segers2020-05-241-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WNDR4300SW, marketed by California ISP SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the WNDR4300 v1. Specifications: * SoC: Atheros AR9344 * RAM: 128 MB * Flash: 128 MB NAND flash * WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz) * Ethernet: 5x 1000Base-T * LED: Power, WAN, LAN, WiFi, USB, WPS * UART: on board, to the right of the RF shield at the top of the board Installation: * Flashing through the OEM web interface: + Connect your computer to the router with an ethernet cable and browse to http://192.168.1.1/ + Log in with the default credentials are admin:password + Browse to Advanced > Administration > Firmware Upgrade in the Netgear interface + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img + Proceed with the firmware installation and give the device a few minutes to finish and reboot. * Flashing through TFTP: + Configure your wired client with a static IP in the 192.168.1.x range, e.g. 192.168.1.10 and netmask 255.255.255.0. + Power off the router. + Press and hold the RESET button (the factory reset button on the bottom of the device, with the red circle around it) and turn the router on while keeping the button pressed. + The power LED will start flashing orange. You can release the button once it switches to flashing green. + Transfer the image over TFTP: $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* treewide: omit IMAGE_SIZE argument from check-sizeSungbo Eo2020-03-211-4/+4
| | | | | | | | | Now that check-size uses IMAGE_SIZE by default, we can skip the argument from image recipes to reduce redundancy. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: gather DEVICE_VARS into one placeSungbo Eo2020-03-211-1/+2
| | | | | | | | | | | Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add mikrotik subtargetRoger Pueyo Centelles2020-03-171-14/+0
| | | | | | | | | | | | | | | | | This commit creates the ath79/mikrotik subtarget in order to support MikroTik devices based on Qualcomm Atheros MIPS SoCs. MikroTik devices need a couple of specific features: the split MiNOR firmware MTD format, which is not used by other devices, and the 4k sector erase size on SPI NOR storage, which can not be added to the ath79/generic and ath79/nand subtargets now. Additionally, the commit moves the two MikroTik devices already in the generic and nand subtargets to this new one. Tested on the RB922 board and the wAP AC router. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: fix indent for wrapped lines in image/nand.mkAdrian Schmutzler2020-03-071-3/+3
| | | | | | | This applies the common indent (one tab) for the wrapped lines of domywifi_dw33d and glinet_gl-ar750s-nor-nand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for DomyWifi DW33DWeiDong Jia2020-03-071-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit ports the device from ar71xx to the ath79 target and modifies the partition layout. 1. Firmware is installed to nand flash. 2. Modify the uboot-env parameter to boot from the nand flash. 3. The kernel size is extended to 5M. 4.nor flash retains the oem firmware. oem partition layout dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00e30000 00010000 "rootfs" mtd3: 00170000 00010000 "kernel" mtd4: 00010000 00010000 "art" mtd5: 00f90000 00010000 "firmware" mtd6: 06000000 00020000 "rootfs_data" mtd7: 02000000 00020000 "backup" new partition layout dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00fa0000 00010000 "oem-firmware" mtd3: 00010000 00010000 "art" mtd4: 00500000 00020000 "kernel" mtd5: 05b00000 00020000 "ubi" mtd6: 02000000 00020000 "oem-backup" MAC address overview: All mac addresses are stored in the art partition. eth0: 0x0 eth1: 0x6 ath9k: 0xc ath10k: 0x12 No valid addresses in 0x1002 and 0x5006. All addresses match the OEM firmware. Install from oem firmware. Enable ssh service: Connect to the router web, click professional, click system-startup, and add dropbear in the local startup input box. Click system-administration, delete ssh-key, and replace your ssh pub key. Restart the router. 1.Upload openwrt firmware to the device scp openwrt-snapshot-r11365-df60a0852c-ath79-nand-domywifi_dw33d-\ squashfs-factory.bin root@192.168.10.1:/tmp 2.modify uboot-env. ssh login to the device: fw_setenv bootcmd 'nboot 0x8050000 0;bootm || bootm 0x9fe80000' Run the fw_printenv command to check if the settings are correct. 3.Write openwrt firmware. ssh login to the device: mtd -r write /tmp/openwrt-snapshot-r11365-df60a0852c-ath79-nand-\ domywifi_dw33d-squashfs-factory.bin /dev/mtd6 The device will restart automatically and the openwrt firmware installation is complete. Restore oem firmware.just erase the kernel partition and the ubi partition. ssh login to the device: mtd erase /dev/mtd4 mtd -r erase /dev/mtd5 Reboot the device Signed-off-by: WeiDong Jia <jwdsccd@gmail.com> [alter flash instruction in commit message] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for MikroTik RouterBOARD 922UAGS-5HPacDRoger Pueyo Centelles2020-02-261-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch ports support for the MikroTik RouterBOARD 922UAGS-5HPacD with a built-in 802.11ac High-Power radio (31dBm), which was already available in the ar71xx target. See https://mikrotik.com/product/RB922UAGS-5HPacD for more info. Specifications: - SoC: Qualcomm Atheros QCA9558 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9882 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V - SFP: 1x host - USB: 1x 2.0 type A - PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems) - SIM slot: 1x mini-SIM Working: - Board/system detection - SPI and NAND storage - PCIe - USB type A host - Wireless - Ethernet - LEDs (user, phy0) - Reset button - Sysupgrade to/from ar71xx Not supported: - RSSI LEDs - SFP cage Installation methods: - Sysupgrade from ar71xx (it is advisable to use the -n option to wipe any previous settings), or - Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: fix SUPPORTED_DEVICES for WNDR4300 and WNDR3700v4Michal Cieslakiewicz2020-01-211-2/+0
| | | | | | | | | | Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300 routers breaks sysupgrade image compatibility with ar71xx builds. Therefore, SUPPORTED_DEVICES variable has to be removed for both devices from target makefile. Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4500 v3Michal Cieslakiewicz2020-01-151-0/+11
| | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4500v3. Router is very similar to WNDR4300v2 and is based on the same PCB. Information gathered from various Internet sources (including https://patchwork.ozlabs.org/patch/809227/) shows following differences to WNDR4300v2: * two USB 2.0 ports with separate LEDs * USB LEDs soldered to secondary pads * WPS and RFKILL buttons soldered to secondary pads * described as N900 device with 3x3:3 MIMO for 2.4GHz radio * power supply requirement is DC 12V 2.5A * vendor HW ID suffix differs in one digit * bigger chassis Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4300 v2Michal Cieslakiewicz2020-01-151-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4300v2. Specification ============= * Description: Netgear WNDR4300 v2 * Loader: U-boot * SOC: Qualcomm Atheros QCA9563 (775 MHz) * RAM: 128 MiB * Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND - NOR: U-boot binary: 256 KiB - NOR: U-boot environment: 64 KiB - NOR: ART Backup: 64 KiB - NOR: Config: 64 KiB - NOR: Traffic Meter: 64 KiB - NOR: POT: 64 KiB - NOR: Reserved: 1408 KiB - NOR: ART: 64 KiB - NAND: Firmware: 25600 KiB (see notes for OpenWrt) - NAND: Language: 2048 KiB - NAND: mtdoops Crash Dump: 128 KiB - NAND: Reserved: 103296 KiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Important Notes =============== 0. NOR Flash (2 MiB) is not touched by OpenWrt installation. 1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows: all space is split between 4 MiB kernel and 124 MiB UBI areas; vendor partitions (language and mtdoops) are removed; kernel space size can be further expanded if needed; maximum image size is set to 25600k for compatibility reasons and can also be increased. 2. CPU clock is 775 MHz, not 750 MHz. 3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI device ID 0xabcd. For ath9k driver to load successfully, this is overriden in DTS with correct value for this chip, 0x0033. 4. RFKILL button is wired to AR9580 pin 9 which is normally disabled by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore 'qca,gpio-mask=<0xf6ff>' hack must be used for button to work properly. 5. USB port is always on, no GPIO for 5V power control has been identified. Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: WNDR4300: increase kernel partition to 4MMichal Cieslakiewicz2020-01-151-1/+1
| | | | | | | | | Increase kernel partition from 2 MiB to 4 MiB for Netgear WNDR routers with NAND flash. Change affects following devices: * Netgear WNDR3700 v4 * Netgear WNDR4300 Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: GL-AR750S (NOR/NAND): limit factory.img kernel size to 2 MBJeff Kletsky2020-01-151-1/+4
| | | | | | | | | | | | | | | | The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size. While sysupgrade can manage kernels up to the present limit of 4 MB, directly flashing a factory.img with a kernel size greater than 2 MB through U-Boot will result in an unbootable device. This commit uses the newly-introduced check-kernel-size build operation to prevent the output of factory.img when the kernel exceeds 2 MB in size, yet permits output of sysupgrade.img as long as the kernel is within KERNEL_SIZE := 4096k Cc: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: gl-ar750s: reduce kernel size to 2M in image MakefileChuanhong Guo2020-01-111-1/+1
| | | | | | | | | | | | | | | | u-boot splits nand factory firmware at 2M offset, flash the first part as kernel into spi nor and the other part as ubi into nand flash. With previous commit increasing kernel size to 4M, generated factory firmware is broken because ubi is at 4M offset. This commit reduces kernel size definition to 2M in image Makefile, producing proper factory image. Partition size in dts is kept unchanged so that sysupgrade to a firmware with 2M+ kernel still works. Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB") Reported-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: rename ATH_SOC to SOCAdrian Schmutzler2019-12-201-6/+6
| | | | | | | This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: harmonize line breaks in image MakefilesAdrian Schmutzler2019-12-201-13/+20
| | | | | | | | | | | | | | | | This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Netgear WNDR3700v4Paul Blazejowski2019-11-141-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNDR3700v4. Router was previously supported by ar71xx target only. Note: device requires 'ar934x-nand' driver in kernel. Specification ============= * Description: Netgear WNDR3700v4 * Loader: U-boot * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 128 MiB (NAND) - U-boot binary: 256 KiB - U-boot environment: 256 KiB - ART: 256 KiB - POT: 512 KiB - Language: 2 MiB - Config: 512 KiB - Traffic Meter: 3 MiB - Firmware: 25 MiB - ART Backup: 256 KiB - Reserved: 96 MiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (amber/green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 2.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Note about partitioning: firmware partition offset (0x6c0000) is hardcoded into vendor's u-boot, so this partition cannot be moved and resized to include Netgear-specific flash areas (pot, language, config, traffic_meter) not used by OpenWrt. Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr3700-v4=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
* ath79: GL-AR750S: provide NAND support; increase kernel to 4 MBJeff Kletsky2019-11-141-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet GL-AR750S has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. At this time, the OEM U-Boot appears to only support loading the kernel from NOR. This configuration is preserved as this time, with the glinet,gl-ar750s-nand name reserved for a potential, future, NAND-only boot. The family of GL-AR750S devices on the ath79 platform now includes: * glinet,gl-ar750m-nor-nand "nand" target * glinet,gl-ar750m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar750s-nor firmware produced by this commit: * glinet,gl-ar750s -- OpenWrt 19.07 ar71xx * glinet,gl-ar750s -- OpenWrt 19.07 ath79 Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the NAND-based variant. Other upgrades to these images, including directly to the NAND-based glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot. NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which enables flashing of NAND factory.img with the current GL-iNet U-Boot, "U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)" The GL-AR750S OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images generated after this commit flash each other directly. This commit changes the control of the USB VBUS to gpio-hog from regulator-fixed introduced by commit 0f6b944c92. This reduces the compressed kernel size by ~14 kB, with no apparent loss of functionality. No other ath79-nand boards are using regulator-fixed at this time. Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Cc: Alexander Wördekemper <alexwoerde@web.de> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: GL-AR300M: provide NAND support; increase to 4 MB kernelJeff Kletsky2019-11-141-8/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet GL-AR300M has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. Devices with both NOR and NAND flash can support independent firmware on each, with U-Boot able to boot from either. The OEM U-Boot will fall back to the NOR firmware after three "unsuccessful" boots. The family of GL-AR300M devices on the ath79 platform now includes: * glinet,gl-ar300m-lite "generic" target, NOR-only board * glinet,gl-ar300m-nand "nand" target * glinet,gl-ar300m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar300m-nor firmware produced by this commit: * gl-ar300m -- OEM v3 NOR ar71xx (openwrt-ar300m16-*.bin) * gl-ar300m -- OpenWrt 18.06 ar71xx * gl-ar300m -- OpenWrt 19.07 ar71xx Other upgrades to these images should be performed through U-Boot. The GL-AR300M OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated after this commit should safely flash each other using sysupgrade. The boot counter is implemented by the OEM using u-boot-env. At this time, it does not appear that the switch on the side of the unit can be used to select NOR vs. NAND boot and the fail-over is only from NAND to NOR. To save flash wear, it is only reset when running the glinet,gl-ar300m-nand firmware. NAND-specific base-files are used to remove impact on existing generic and tiny targets. As there is now no "generic" build appropriate for the GL-AR300M16, (or for users of the GL-AR300M that do not need access to NAND) it will be introduced in a subsequent commit. Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: fix several issues for ZyXEL NBG6716Adrian Schmutzler2019-11-021-10/+11
| | | | | | | | | | | | | This fixes several issues introduced with ZyXEL NBG6716 support: - Inhomogeneous indent - Wrong ath10k MAC patching function - Wrong brackets for pad-to in nand.mk - Add missing DEVICE_MODEL - Remove k2t.sh include (copy/paste leftover) Fixes: 99835e09992b ("ath79: add support for ZyXEL NBG6716") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Netgear WNDR4300Michal Cieslakiewicz2019-11-021-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNDR4300. Router was previously supported by ar71xx target only. Note: device requires 'ar934x-nand' driver in kernel. Specification ============= * Description: Netgear WNDR4300 * Loader: U-boot * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 128 MiB (NAND) - U-boot binary: 256 KiB - U-boot environment: 256 KiB - ART: 256 KiB - POT: 512 KiB - Language: 2 MiB - Config: 512 KiB - Traffic Meter: 3 MiB - Firmware: 25 MiB - ART Backup: 256 KiB - Reserved: 96 MiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (amber/green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 2.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Note about partitioning: firmware partition offset (0x6c0000) is hardcoded into vendor's u-boot, so this partition cannot be moved and resized to include Netgear-specific flash areas (pot, language, config, traffic_meter) not used by OpenWrt. Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Aerohive HiveAP 121David Bauer2019-10-271-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Aerohive HiveAP-121. It was previously already supported in the ar71xx subtarget. The following is copied from the commit which added ar71xx support: Specification: - SoC: Atheros AR9344-BC2A at 560MHz - WiFi 1: 2.4GHz Atheros AR9340? - SoC - WiFi 2: 5.0GHz Atheros AR9382-AL1A - Memory: 128MB from 2x Nanya NT5TU32M16DG-AC - SPI: 1MB Macronix MX25L8006E - NAND: 128MB Hynix H27U1G8F2BTR-BC - Ethernet: Atheros AR8035-A - USB: 1x 2.0 - TPM: Atmel SC3204 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, download and flash LEDE factory image over tftp: dhcp; setenv serverip tftp-server-ip; tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin; nand erase 0x800000 0x800000; nand write 0x81000000 0x800000 0x800000; reset; Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for ZyXEL NBG6716André Valentin2019-10-271-0/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Attention: Kernel partition size has been enlarged to 4MB. To switch, you must update to latest ar71xx-nand snapshort and flash the sysupgrade-4M-Kernel.bin: zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f You will end up with a fresh config if you do not inject config into the image. The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but ath79 can only use the first 128MB. Therefore the complete NAND needs to be overwritten. If not, the old UBI may make problems and lead to reboot loop. Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6716> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6716> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6716> ATSE NBG6716 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6716> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6716> ATGU |NBG6716# Signed-off-by: André Valentin <avalentin@marcant.net>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-061-1/+1
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix missing DEVICE_VENDOR for some devicesChen Minqiang2019-07-101-0/+1
| | | | Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ath79: split DEVICE_TITLE in multiple variablesPaul Spooren2019-07-041-1/+2
| | | | | | | | | | | | | | This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-311-2/+2
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: remove duplicate image build variablesMathias Kresin2018-12-061-2/+2
| | | | | | | Remove image build variables which are set to the same value as the default image build recipe. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix GL.iNet GL-AR300M sysupgradeMathias Kresin2018-12-061-2/+2
| | | | | | | | | | | The userspace boardname derived from the dts compatible was out of sync with the expected board added to the image metadata. This way a sysupgrade is refused. Sync the userspace boardname and the baordname used in the image metdata to allow a seamless sasupgrade. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: rename qca9533.dtsi to qca953x.dtsiChuanhong Guo2018-12-061-1/+1
| | | | | | | | | qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE. Rename the misleading dtsi names and fix the SoC type of gl-ar300m. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [apply the changes for the gl-x750 as well] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add initial nand support for gl-ar300mMarty E. Plummer2018-06-181-0/+13
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>