aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/nand/base-files/etc/hotplug.d
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for MikroTik RouterBOARD 922UAGS-5HPacDRoger Pueyo Centelles2020-02-261-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch ports support for the MikroTik RouterBOARD 922UAGS-5HPacD with a built-in 802.11ac High-Power radio (31dBm), which was already available in the ar71xx target. See https://mikrotik.com/product/RB922UAGS-5HPacD for more info. Specifications: - SoC: Qualcomm Atheros QCA9558 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9882 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V - SFP: 1x host - USB: 1x 2.0 type A - PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems) - SIM slot: 1x mini-SIM Working: - Board/system detection - SPI and NAND storage - PCIe - USB type A host - Wireless - Ethernet - LEDs (user, phy0) - Reset button - Sysupgrade to/from ar71xx Not supported: - RSSI LEDs - SFP cage Installation methods: - Sysupgrade from ar71xx (it is advisable to use the -n option to wipe any previous settings), or - Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add support for Netgear WNDR4500 v3Michal Cieslakiewicz2020-01-151-2/+4
| | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4500v3. Router is very similar to WNDR4300v2 and is based on the same PCB. Information gathered from various Internet sources (including https://patchwork.ozlabs.org/patch/809227/) shows following differences to WNDR4300v2: * two USB 2.0 ports with separate LEDs * USB LEDs soldered to secondary pads * WPS and RFKILL buttons soldered to secondary pads * described as N900 device with 3x3:3 MIMO for 2.4GHz radio * power supply requirement is DC 12V 2.5A * vendor HW ID suffix differs in one digit * bigger chassis Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4300 v2Michal Cieslakiewicz2020-01-151-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4300v2. Specification ============= * Description: Netgear WNDR4300 v2 * Loader: U-boot * SOC: Qualcomm Atheros QCA9563 (775 MHz) * RAM: 128 MiB * Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND - NOR: U-boot binary: 256 KiB - NOR: U-boot environment: 64 KiB - NOR: ART Backup: 64 KiB - NOR: Config: 64 KiB - NOR: Traffic Meter: 64 KiB - NOR: POT: 64 KiB - NOR: Reserved: 1408 KiB - NOR: ART: 64 KiB - NAND: Firmware: 25600 KiB (see notes for OpenWrt) - NAND: Language: 2048 KiB - NAND: mtdoops Crash Dump: 128 KiB - NAND: Reserved: 103296 KiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Important Notes =============== 0. NOR Flash (2 MiB) is not touched by OpenWrt installation. 1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows: all space is split between 4 MiB kernel and 124 MiB UBI areas; vendor partitions (language and mtdoops) are removed; kernel space size can be further expanded if needed; maximum image size is set to 25600k for compatibility reasons and can also be increased. 2. CPU clock is 775 MHz, not 750 MHz. 3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI device ID 0xabcd. For ath9k driver to load successfully, this is overriden in DTS with correct value for this chip, 0x0033. 4. RFKILL button is wired to AR9580 pin 9 which is normally disabled by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore 'qca,gpio-mask=<0xf6ff>' hack must be used for button to work properly. 5. USB port is always on, no GPIO for 5V power control has been identified. Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR3700v4Paul Blazejowski2019-11-141-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNDR3700v4. Router was previously supported by ar71xx target only. Note: device requires 'ar934x-nand' driver in kernel. Specification ============= * Description: Netgear WNDR3700v4 * Loader: U-boot * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 128 MiB (NAND) - U-boot binary: 256 KiB - U-boot environment: 256 KiB - ART: 256 KiB - POT: 512 KiB - Language: 2 MiB - Config: 512 KiB - Traffic Meter: 3 MiB - Firmware: 25 MiB - ART Backup: 256 KiB - Reserved: 96 MiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (amber/green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 2.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Note about partitioning: firmware partition offset (0x6c0000) is hardcoded into vendor's u-boot, so this partition cannot be moved and resized to include Netgear-specific flash areas (pot, language, config, traffic_meter) not used by OpenWrt. Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr3700-v4=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
* ath79: GL-AR750S: provide NAND support; increase kernel to 4 MBJeff Kletsky2019-11-141-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet GL-AR750S has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. At this time, the OEM U-Boot appears to only support loading the kernel from NOR. This configuration is preserved as this time, with the glinet,gl-ar750s-nand name reserved for a potential, future, NAND-only boot. The family of GL-AR750S devices on the ath79 platform now includes: * glinet,gl-ar750m-nor-nand "nand" target * glinet,gl-ar750m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar750s-nor firmware produced by this commit: * glinet,gl-ar750s -- OpenWrt 19.07 ar71xx * glinet,gl-ar750s -- OpenWrt 19.07 ath79 Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the NAND-based variant. Other upgrades to these images, including directly to the NAND-based glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot. NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which enables flashing of NAND factory.img with the current GL-iNet U-Boot, "U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)" The GL-AR750S OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images generated after this commit flash each other directly. This commit changes the control of the USB VBUS to gpio-hog from regulator-fixed introduced by commit 0f6b944c92. This reduces the compressed kernel size by ~14 kB, with no apparent loss of functionality. No other ath79-nand boards are using regulator-fixed at this time. Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Cc: Alexander Wördekemper <alexwoerde@web.de> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: fix several issues for ZyXEL NBG6716Adrian Schmutzler2019-11-021-2/+1
| | | | | | | | | | | | | This fixes several issues introduced with ZyXEL NBG6716 support: - Inhomogeneous indent - Wrong ath10k MAC patching function - Wrong brackets for pad-to in nand.mk - Add missing DEVICE_MODEL - Remove k2t.sh include (copy/paste leftover) Fixes: 99835e09992b ("ath79: add support for ZyXEL NBG6716") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Netgear WNDR4300Michal Cieslakiewicz2019-11-021-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNDR4300. Router was previously supported by ar71xx target only. Note: device requires 'ar934x-nand' driver in kernel. Specification ============= * Description: Netgear WNDR4300 * Loader: U-boot * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 128 MiB (NAND) - U-boot binary: 256 KiB - U-boot environment: 256 KiB - ART: 256 KiB - POT: 512 KiB - Language: 2 MiB - Config: 512 KiB - Traffic Meter: 3 MiB - Firmware: 25 MiB - ART Backup: 256 KiB - Reserved: 96 MiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (amber/green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 2.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Note about partitioning: firmware partition offset (0x6c0000) is hardcoded into vendor's u-boot, so this partition cannot be moved and resized to include Netgear-specific flash areas (pot, language, config, traffic_meter) not used by OpenWrt. Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: move base-files for ZyXEL NBG6716Adrian Schmutzler2019-10-272-0/+43
Due to rebase of the base-files split patch after adding support for the ZyXEL NBG6716, its base-files were added to the generic subtarget, although the device belongs to the nand subtarget. This moves the definitions to their proper locations. Fixes: 0130022baec0 ("ath79: split base-files into subtargets") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [improve commit message, rebase] Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-17 16:34:06 +0000