aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* ath79: phy-ar7200-usb: do not print error on defered initJohann Neuhauser2020-06-032-4/+6
| | | | | | | | | | | This is only a cosmetic correction, as the driver works as expected. However, the error message confuses users about a missing reset definition. On a defered init we don't see the following error message now: [ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* kernel: bump 5.4 to 5.4.43Petr Štetiar2020-06-021-1/+1
| | | | | | | | | | | Refreshed patches, removed upstreamed patch: bcm27xx: 950-0642-component-Silence-bind-error-on-EPROBE_DEFER.patch Run tested: qemu-x86-64 Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add label MAC address for TP-Link RE450 v2/v3Adrian Schmutzler2020-05-311-0/+1
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link RE450 v3Andreas Wiese2020-05-317-176/+251
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE450 v3 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. This device is nearly identical to RE450 v2 besides a modified flash layout (hence I think force-flashing a RE450v2 image will lead to at least loss of MAC address). Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button- - possible UART header on PCB¹ Flash instruction: Apply factory image in OEM firmware web-gui. ¹ Didn't check to connect as I didn't even manage to connect on RE450v2 (AFAIU it requires disconnecting some resistors, which I was too much of a coward to do). But given the similarities to v2 I think it's the same or very similar procedure (and most likely also the only way to debrick). Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net> [remove dts-v1 and compatible in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR802N V1 and V2Lech Perczak2020-05-316-1/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of Flash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to web interface: [V1] http://192.168.0.1 [V2] http://192.168.0.254 Default user is "admin" & password is "admin". On V2, there is no DHCP server running by default, so remember to set IP manually. - Go to "System Tools -> Firmware Upgrade" - Browse for firmware: [V1] "*.factory.bin" [V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model Web interface may complain if filename is too long. In such case, rename .bin to something shorter. - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Notes: When porting from ar71xx target to ath79, I found out that on V2, reset button is on GPIO12 and active low, instead of GPIO11 and active high. By cross-flashing V1 firmware to V2, I confirmed the same is true for V1. Also according to manual of V1, this one also has green LED instead of blue - both of those issues were fixed accordingly. The MAC address assignment has been checked with OEM firmware. Installation manual based on ar71xx support by Thomas Roberts Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [slightly adjust commit message, add MAC address comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: update WA/XC devices UBNT_VERSION to 8.5.3Roger Pueyo Centelles2020-05-311-3/+3
| | | | | | | | | | | | | | Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION to be at least 8.5.3, otherwise the image is rejected: New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3 Versions: New(525568) 8.5.0, Required(525571) 8.5.3 Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3' For consistency, also increase version number for XC devices. Tested-by: Pedro <pedrowrt@cas.cat> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: fix LEDs for GL.inet GL-AR150Adrian Schmutzler2020-05-312-12/+10
| | | | | | | | | | | | | | | | | Since the wireless LED was used for boot and set up with a DT trigger, the WiFi indication hasn't worked on ath79 at all. In addition, a look into the manual revealed that the OEM configuration is as follows: LED 1 (green): power LED 2 (green): configurable LED 3 (red): wireless So, let's just keep the WiFi trigger and convert the rest to its "intended" use. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* packages/boot: remove rbcfgThibaut VARÈNE2020-05-281-1/+0
| | | | | | | The new sysfs soft_config driver makes buggy rbcfg obsolete and entirely replaces it. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: add support for COMFAST CF-E130N v2Pavel Balan2020-05-284-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless CPE with a single Ethernet port and a 802.11bgn radio. Specifications: - QCA9531 SoC - 1x 10/100 Mbps Ethernet with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 5 dBi built-in antenna - POWER/LAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. The U-boot bootloader also contains a backup TFTP client to upload the firmware from. Upon boot, it checks its ethernet network for the IP 192.168.1.10. Host a TFTP server and provide the image to be flashed as file firmware_auto.bin. MAC address setup: The art partition contains four consecutive MAC addresses: 0x0 aa:bb:cc:xx:xx:c4 0x6 aa:bb:cc:xx:xx:c6 0x1002 aa:bb:cc:xx:xx:c5 0x5006 aa:bb:cc:xx:xx:c7 However, the manufacturer in its infinite wisdom decided that one address is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's overwriting the existing and valid address in 0x1002). This is obviously also the address on the device's label. Signed-off-by: Pavel Balan <admin@kryma.net> [fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename ATH_SOC to SOC] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: replace tab after DT label by spaceAdrian Schmutzler2020-05-288-8/+8
| | | | | | The common separator in this case is a single space. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: increase spi clock for D-Link DIR-842Sebastian Schaper2020-05-261-1/+2
| | | | | | | | | AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz. Tested on revisions C1 and C3. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: define switch reset-gpios for D-Link DIR-842Sebastian Schaper2020-05-261-8/+2
| | | | | | | | | | GPIO 11 needs to be pulled high for the external gigabit switch to work, this is currently solved via gpio-hog. Replace with phy0 reset-gpios. Tested on revisions C1 and C3. Reset button is still working for reboot, to enter failsafe, and to enter bootloader http recovery. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: fix LEDs for D-Link DIR-842Sebastian Schaper2020-05-264-30/+12
| | | | | | | | | | | | | | | The device has a total of 8 LEDs, 5 of which are controlled by the switch (LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC. * led_power is on GPIO 5 (not 15), boot flashing sequence is now visible * remove led 'internet', since it is only connected to the switch * remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect Tested on revisions C1 and C3. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79/mikrotik: add missing kernel config symbol for 5.4Roger Pueyo Centelles2020-05-261-0/+1
| | | | | | | | The UBIFS_FS_ZSTD is exposed when UBIFS is enabled. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: properly insert local mtd partition parsersAdrian Schmutzler2020-05-251-10/+13
| | | | | | | | | | | | | | | | Between 4.19 and 5.4, the kernel moved the partition parsers into the parsers subdirectory. This led to some necessary rebasing of our local patches for parsers, which partially has been performed without caring about where the code was inserted. This commit tries to adjust our local patches so that parsers are inserted at the "proper" positions with respect to alphabetic sorting (if possible). Thus, the commit is cosmetic. While this might look useless now, it will make life easier when adding other parsers in the future or for rebasing on kernel changes. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79/nand: add support for Netgear WNDR4300SWStijn Segers2020-05-245-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WNDR4300SW, marketed by California ISP SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the WNDR4300 v1. Specifications: * SoC: Atheros AR9344 * RAM: 128 MB * Flash: 128 MB NAND flash * WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz) * Ethernet: 5x 1000Base-T * LED: Power, WAN, LAN, WiFi, USB, WPS * UART: on board, to the right of the RF shield at the top of the board Installation: * Flashing through the OEM web interface: + Connect your computer to the router with an ethernet cable and browse to http://192.168.1.1/ + Log in with the default credentials are admin:password + Browse to Advanced > Administration > Firmware Upgrade in the Netgear interface + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img + Proceed with the firmware installation and give the device a few minutes to finish and reboot. * Flashing through TFTP: + Configure your wired client with a static IP in the 192.168.1.x range, e.g. 192.168.1.10 and netmask 255.255.255.0. + Power off the router. + Press and hold the RESET button (the factory reset button on the bottom of the device, with the red circle around it) and turn the router on while keeping the button pressed. + The power LED will start flashing orange. You can release the button once it switches to flashing green. + Transfer the image over TFTP: $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ath79: add support for Enterasys WS-AP3705iDavid Bauer2020-05-226-1/+261
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Atheros AR9344 RAM: 128M DDR2 FLASH: 2x Macronix MX25L12845EM 2x 16MiB SPI-NOR WLAN2: Atheros AR9344 2x2 2T2R WLAN5: Atheros AR9580 2x2 2T2R SERIAL: Cisco-RJ45 on the back (115200 8n1) Installation ------------ The U-Boot CLI is password protected (using the same credentials as the OS). Default is admin/new2day. 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to 1401A8C0.img. Configure the TFTP server to listen at 192.168.1.66/24. 2. Connect the TFTP server to the access point. 3. Connect to the serial console of the access point. Attach power and interrupt the boot procedure when prompted (bootdelay is 1 second). 4. Configure the U-Boot environment for booting OpenWrt from Ram and flash: $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000' $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66; tftpboot 0x85000000; bootm' $ setenv bootcmd 'run boot_openwrt' $ saveenv 5. Load OpenWrt into memory: $ run ramboot_openwrt Wait for the image to boot. 6. Transfer the OpenWrt sysupgrade image to the device. Write the image to flash using sysupgrade: $ sysupgrade -n /path/to/openwrt-sysuograde.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Do not build buffalo_whr-g301n by defaultHauke Mehrtens2020-05-211-0/+1
| | | | | | The squashfs partition is getting too big. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add support for TP-Link TL-WA901ND v4 and v5Adrian Schmutzler2020-05-188-72/+174
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79. They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6. Specifications: SoC: TP9343 Flash/RAM: 4/32 MiB CPU: 750 MHz WiFi: 2.4 GHz b/g/n Ethernet: 1 port (100M) Flashing instructions: Upload the factory image via the vendor firmware upgrade option. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to * (see below) 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. * The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for both variants. In ar71xx, a MAC address with offset 1 was used for ethernet port. That's probably wrong, but this commit sticks to it until we know the correct value. Like in ar71xx, this builds the default factory.bin with EU country code. Thanks to Leonardo Weiss for testing on the v5. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBeam 5AC 500Roger Pueyo Centelles2020-05-175-0/+127
| | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti PowerBeam 5AC 500 (PBE-5AC-500) is an outdoor 802.11ac 5 GHz bridge with a radio feed and a dish antenna. Specifications: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR (mx25l12805d) - Ethernet: 1x 10/100/1000 Mbps Atheros 8031, 24 Vdc PoE-in - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue - UART: not tested Not supported: - RSSI LEDs (probably through 74HC595 chip) Installation from stock airOS firmware: - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at https://openwrt.org/toh/ubiquiti/common Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: increase spi frequency on tp-link tl-wr1043nd v2Aleksander Jan Bajkowski2020-05-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | Increase SPI frequency to 33.333 MHz. It's maximum frequency supported by SPI Flash memory chip without Fast read opcode. Before: $ time dd if=/dev/mtd1 of=/dev/null bs=8M 0+1 records in 0+1 records out real 0m 3.21s user 0m 0.00s sys 0m 3.21s After: $ time dd if=/dev/mtd1 of=/dev/null bs=8M 0+1 records in 0+1 records out real 0m 2.52s user 0m 0.00s sys 0m 2.52s Tested on TP-Link TL-WR1043ND V2. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* kernel: bump 5.4 to 5.4.41Koen Vandeputte2020-05-141-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: imx6 Runtime-tested on: imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.122Koen Vandeputte2020-05-121-1/+2
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 551-loop-Better-discard-support-for-block-devices.patch Fixed: - CVE-2020-11884 - CVE-2020-12114 - CVE-2019-3016 - CVE-2020-11669 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: dts: add missing 'serial0' alias for TP-Link TL-MR3040v2Lech Perczak2020-05-081-0/+1
| | | | | | | | Out of all devices currently supported based on AR9331 chipset, this one had the 'serial0' alias missing. Add it to fix setting of /dev/console and login shell on the onboard UART. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79/mikrotik: load caldata via sysfs loaderThibaut VARÈNE2020-05-082-4/+6
| | | | | | | | | | | | | This commit takes advantages of base-files 220 which introduces routines to perform caldata loading directly via the kernel sysfs loader helper. This has the benefits of not wasting flash space to store caldata. Memory footprint is reduced to the bare minimum: for devices that don't need MAC patching, the caldata is loaded directly, for devices that do need MAC patching, the caldata is extracted to /tmp, patched and then loaded. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79/mikrotik: use standard caldata functionsThibaut VARÈNE2020-05-084-33/+10
| | | | | | | With the implementation of a sysfs interface to access WLAN data, this target no longer needs a special wrapper to extract caldata. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79/mikrotik: don't use mtd-mac-address in DTSThibaut VARÈNE2020-05-083-5/+9
| | | | | | | | | | | | | | | | | | As evidenced here[1] the device MAC address can be stored at a random offset in the hard_config partition. Rely on sysfs to update the MAC address correctly. To match sticker and vendor OS behavior, WAN MAC is set to the device base MAC and LAN MAC is incremented from that. Note: this will trigger a harmless kernel message during boot: ag71xx 19000000.eth: invalid MAC address, using random address There is no clean workaround to prevent this message from being emitted. [1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021 Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79/mikrotik: enable mikrotik platform driverThibaut VARÈNE2020-05-081-0/+2
| | | | Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79/mikrotik: use routerbootpart partitionsThibaut VARÈNE2020-05-082-23/+12
| | | | | | | Enable routerbootpart partitions on MikroTik devices. Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79/mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTSThibaut VARÈNE2020-05-081-0/+1
| | | | Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: fix dts of Teltonika RUT9xx devicesDaniel Golle2020-04-292-2/+2
| | | | | | The previous commits were missing a semicolon. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for Teltonika RUT955 H7V3C0Daniel Golle2020-04-295-1/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board was previously supported in ar71xx as 'RUT9XX'. The difference between that and the other RUT955 board already supported in ath79 is that instead of the SPI shift registers driving the LEDs and digital outputs that model got an I2C GPIO expander instead. To support LEDs during early boot and interrupt-driven digital inputs, I2C support as well as support for PCA953x has to be built-in and cannot be kernel modules, hence select those symbols for ath79/generic. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344) - built-in 4G/3G module (example: Quectel EC-25EU) - internal microSD slot (spi-mmc, buggy and disabled for now) - RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0) - RS422/RS485 (AR934x high speed UART, /dev/ttyATH1) - analog 0-24V input (MCP3221) - various digital inputs and outputs incl. a relay - 11x LED (4 are driven by AR9344, 7 by PCA9539) - 2x miniSIM slot (can be swapped via GPIO) - 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS) - 1x button (reset) - DC jack for main power input (9-30 V) - debugging UART available on PCB edge connector Serial console (/dev/ttyS0) pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1". Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: split Teltonika RUT955 to support other RUT9xx modelsDaniel Golle2020-04-292-171/+198
| | | | | | | | | Split device-tree of Teltonika RUT955 into a generic RUT9xx part and a part specific to that version of RUT955 already supported. Also harmonize GPIO and LED names with what is used by the vendor firmware and assign RS485 DTR signal. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add SUPPORTED_DEVICES based on ar71xx for some devicesAdrian Schmutzler2020-04-282-0/+13
| | | | | | | | | This adds some still-missing board names for old TP-Link devices to ath79 SUPPORTED_DEVICES. Fixes: FS#3017 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath10k-ct-firmware: rename ct-htt packagesÁlvaro Fernández Rojas2020-04-281-1/+1
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: indicate boot/failsafe/upgrade for NanoBeam/Nanostation ACAdrian Schmutzler2020-04-272-2/+14
| | | | | | | | Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC and Nanostation AC as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBeam 5AC Gen2Roger Pueyo Centelles2020-04-275-2/+80
| | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac 5 GHz bridge with a radio feed and a dish antenna. The device is hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs. Specifications: - SoC: Qualcomm Atheros AR9342 rev 2 - RAM: 64 MB DDR2 - Flash: 16 MB SPI NOR (mx25l12805d) - Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff - WiFi 2.4 GHz: Atheros AR9340 (SoC-based) - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue. - UART: not tested Installation from stock airOS firmware: - Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [changed device name in commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: enable SGMII workaround for affected boardsDavid Bauer2020-04-273-0/+8
| | | | | | | These boards suffer from a sudden inability to establish a link on the SGMII. Enable the workaround to fix the link when it dies. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: unify version dependent codeDavid Bauer2020-04-271-5/+1
| | | | | | | Use IS_ERR_OR_NULL macro to use the same code on kernel 4.19 as well as 5.4. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: remove code for legacy kernelsDavid Bauer2020-04-271-32/+0
| | | | | | | ath79 does not support kernels prior to 4.19 anymore. Remove legacy code for those kernels from the ag71xx driver. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: remove unused TP-Link partition parserDavid Bauer2020-04-274-496/+0
| | | | | | | This parser was added with the target, but no device seems to use it currently, as all partitions are specified in the device-tree. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix QCA953x DDR and GPIO compatible bindingsDavid Bauer2020-04-241-2/+2
| | | | | | | The memory as well as GPIO controller had the wrong SoC name used for their compatible binding. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: correct QCA9550 machine compatible bindingDavid Bauer2020-04-2414-14/+14
| | | | | | | Some boards using a QCA9556 or QCA9558 had their machine compatible binding incorrectly set to qca,qca9557. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: rename qca9557.dtsi to qca955x.dtsiDavid Bauer2020-04-2426-29/+29
| | | | | | | | | | | There are at least 3 different chips in the Scorpion series of SoCs. Rename the common DTSI to better reflect it's purpose for the whole series. Also rename the compatible bindings from qca,ar9557 and qca,qca9557 to qca,qca9550. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: move tplinkpart.c parser to patchesAdrian Schmutzler2020-04-243-253/+462
| | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Like for myloader.c in the previous patch, this patch moves tplinkpart.c to the kernel patches, so the code and the kernel includes are at the same location and the path can be adjusted per kernel. While at it, remove some outdated kernel version switches from the C code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: fix include of myloader.o since kernel 5.4Adrian Schmutzler2020-04-241-3/+3
| | | | | | | | | | | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Based on this, the selection of myloader.o in OpenWrt was also moved to that subdirectory, while the Kconfig and our local myloader.c file remained in /drivers/mtd. This resulted in linking errors like the following (on ath25@5.4): make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ... needed by 'drivers/mtd/parsers/built-in.a'. Stop. make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2 make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2 Since myloader.c is not too big, this patch moves it to the kernel patches, allowing to adjust the path for kernel 5.4 and keeping Makefiles and file paths better in sync. Other patches have been refreshed accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for AVM FRITZ!WLAN Repeater 450EDavid Bauer2020-04-198-90/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the device afterwards to boot OpenWRT. Tested-by: Andreas Ziegler <dev@andreas-ziegler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: remove stray pipeDavid Bauer2020-04-171-1/+1
| | | | | | Fixes: 8918c038f330 ("ath79: add support for AVM FRITZ!WLAN Repeater 1750E") Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for AVM FRITZ!WLAN Repeater 1750EDavid Bauer2020-04-177-13/+237
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!WLAN Repeater 1750E SOC: Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 WLAN2: QCA9880 5 GHz 802.11 n/ac 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (correct MAC) - 5 GHz WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the Device afterwards to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add QCA9550 reset sequenceDavid Bauer2020-04-177-2/+280
| | | | | | | | | | | | | | | | | The QCA9550 family of SoCs have a slightly different reset sequence compared to older chips. Normally the bootloader performs this sequence, however some bootloader implementation expect the operating system to clear the reset. Also get the PCIe resets from OF to support the second RC of the QCA9558. This is required for the AVM FRITZ!WLAN Repeater 1750E to work, as EVA leaves the PCIe bus in reset. Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-20 13:14:15 +0000