| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only (8 MiB variant).
Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
16 MiB for Russia and China markets. Apart from flash size both variants
share the same hardware specification.
Specification
=============
* Description: Netgear WNR2200
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 64 MiB
* Flash: 8 MiB or 16 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 7808 KiB or 16000 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
| |
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Due to rebase of the base-files split patch after adding support
for the ZyXEL NBG6716, its base-files were added to the generic
subtarget, although the device belongs to the nand subtarget.
This moves the definitions to their proper locations.
Fixes: 0130022baec0 ("ath79: split base-files into subtargets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[improve commit message, rebase]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit adds support for the Aerohive HiveAP-121. It was previously
already supported in the ar71xx subtarget.
The following is copied from the commit which added ar71xx support:
Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:
dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
| |
This commit adds PCI support for the whole ath79 target. Previously,
this was only done in the generic and tiny subtargets.
With the introduction of the HiveAP-121, PCI will be a requirement for
all subtargets, thus moving PCI support to the target configuration.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For several devices, wmac MAC address is set from art 0x1002
explicitly by using mtd-mac-address although mtd-cal-data is
pulled from art 0x1000.
With the MAC address in 0x1002, the driver should automatically
use it when reading caldata from 0x1000. Thus, remove the
redundant mtd-mac-address for those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Jeff Kletsky <git-commits@allycomm.com>
Tested-by: Karl Palsson <karlp@etactica.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Until upstream commit 6d4cd041f0af("net: phy: at803x: disable delay
only for RGMII mode"), delays were not disabled on driver probe
for the Atheros AR803x PHYs, although the RX delay is enabled on
soft and hard reset.
In addition, the TX delay setting is retained on soft-reset.
This patch disables both delays on config init to align the behavior
with kernel 5.1 and higher. It can be safely dropped with kernel 5.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space (especially helpful for the tiny devices).
The only script remaining in parent base-files is
/etc/hotplug.d/ieee80211/00-wifi-migration, everything else is
moved/split.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (generic) 49135 B
split (generic) 48533 B (- 0.6 kiB)
split (tiny) 43337 B (- 5.7 kiB)
split (nand) 44423 B (- 4.6 kiB)
Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
This fixes the remaining IMAGE_SIZE issues in ath79 target.
All devices in target have been checked, so together with
previous patches this target should be "clean" afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
So far, IMAGE_SIZE is set as follows:
tplink-4m* 3904k 0x3d0000
tplink-8m* 7936k 0x7c0000
tplink-16m* 15872k 0xf80000
However, based on the size of firmware partitions in DTS it should
be:
tplink-4m* 3904k 0x3d0000
tplink-8m* 8000k 0x7d0000
tplink-16m* 16192k 0xfd0000
All (!) 8m*/16m* devices actually follow the latter scheme, which
is also consistent in terms of left free space for other
partitions. Thus, fix it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by:
1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"),
since despite two all subdefinition have different values.
2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k).
3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node
since all have same size (it is defined in parent DTSI ...).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Factory image generated for Netgear WNR1000 v2 has incorrect device
and hardware ID information in header due to missing makefile
variables. This fix adds them to device section.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Attention: Kernel partition size has been enlarged to 4MB.
To switch, you must update to latest ar71xx-nand snapshort and flash the
sysupgrade-4M-Kernel.bin:
zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f
You will end up with a fresh config if you do not inject config into the image.
The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but
ath79 can only use the first 128MB. Therefore the complete NAND needs to be
overwritten. If not, the old UBI may make problems and lead to reboot loop.
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6716> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6716>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6716> ATSE NBG6716
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6716> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6716> ATGU
|NBG6716#
Signed-off-by: André Valentin <avalentin@marcant.net>
|
|
|
|
|
|
|
|
|
|
| |
Rework DEVICE_VENDOR, DEVICE_MODEL, and DEVICE_VARIANT
for the GL-AR300M series on the ath79-generic target.
Changes GL-AR300M-Lite to the current form with
DEVICE_VARIANT := Lite (board name is unchanged)
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The GL-AR750S has an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.2 ms period, ~89 kHz
The board has well-labeled (unpopulated) headers for serial and I2C
along the front edge of the board (the edge with the LEDs). Looking
from the top, rear of the unit (behind Ethernet jacks)
-------------------------------------------
5G_LED 2G_LED PWR_LED
O O O O O O O
3 S S G T R G
V C D N X X N
3 L A D D
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The GL-AR300M series have an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.4 ms period, ~88 kHz
The board has two sets of (unpopulated) headers. While facing the
back of the board (looking into the Ethernet jacks), and looking from
the top, the one on the left edge of the baord with four holes is the
I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards.
| (Patch antenna)
|
|
| O GND
| O SDA / GPIO 17
| O SCL / GPIO 16
| ⊡ 3V3 (square land)
|
| (Ethernet jacks)
https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states
"Note: I2C is not working in some early version of the router."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
| |
Previous commit 0cc87b3 "ath79: image: disable sysupgrade images for
routerstations and ja76pf2" doesn't remedy completely the posibility of
bricking the device, since user could try to downgrade with an older
image. Therefore disable sysupgrade code for these boards with a small
note.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
|
|
|
|
| |
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
This removes a useless empty default case.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This converts leading whitespaces to tabs and removes a double
newline at the end of the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
| |
Several Archer Cxx devices were using board-specific LED names in
ar71xx, which were changed to "tp-link:*" in ath79.
This patch adds migration for them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Several devices added to LED migration script will just have their
(old) board name converted to tp-link.
By using a variable for this, the amount of code in the migration
script can be reduced and the chance for typos is reduced.
This patch also introduces the marker for beginning of a pattern
"^" to the regex, so the match is more specific.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ar71xx images for the Ubiquiti NanoStation M (XM) devices use
"nanostation-m" as board name, but the ath79 images are only
compatible with the "nano-m" board name, so sysupgrade complains.
By changing this additional supported device, sysupgrade smoothly
upgrades from ar71xx to ath79.
Ref: openwrt#2418
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The code line patching ath9k MAC address for this device contains
a wrong number of arguments including an unset "$mac", which
looks like a typo or copy/paste mistake.
This has been introduced already in the device support commit
745dee11ac78 ("ath79: add support for WD My Net Wi-Fi Range
Extender").
This patch just removes the "$mac" argument, leaving a formally
valid line. (No on-device test has been performed.)
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds ath79 support for Netgear WNR1000v2.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.
Specification
=============
* Description: Netgear WNR1000 v2
* Loader: U-boot
* SOC: Atheros AR7240 (340 MHz)
* RAM: 32 MiB
* Flash: 4 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 3712 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9285)
* USB: no
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr1000-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds ath79 support for Netgear WNR2000v3.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.
Specification
=============
* Description: Netgear WNR2000 v3
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 32 MiB
* Flash: 4 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 3712 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: no
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch improves ath79 support for Netgear WNR612v2.
Router functionality becomes identical to ar71xx version.
Changes include:
* software control over LAN LEDs via sysfs
* correct MAC addresses for network interfaces
* correct image size in device definition
* dts: 'keys' renamed to 'ath9k-keys'
* dts: 'label-mac-device' set to eth1 (LAN)
* dts: formatting adjustments
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit.
This patch adds new DTS settings to control LAN LEDs and CLKs that allow
full software control over these diodes - exactly the same is done by ar71xx
target in device setup phase for many routers (WNR2000v3 for example).
'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits.
'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and
AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along
with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and
buttons on device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
router.
Specification
SoC: Atheros AR1022
RAM: 64 MB DDR2
Flash: 8 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled, 5x switch
Buttons: 2x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Known issues
5GHz LED doesn't work
Additional information
When TX line on UART is connected, and board is switched on from power
off state, the DDR memory training may fail.
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), which may or may
not work with introduced images.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.
Also fix the phy-mode to represent the actual state needed for ethernet
to function.
Reported-by: Moritz Schreiber <moritz@mosos.de>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch contains updated driver for Atheros NAND Flash Controller
written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc').
ath79 version has adapted to work with kernel 4.19 and Device Tree.
It has also been renamed to 'ar934x-nand' to avoid confusion with
Near-Field Communication technology.
Controller is present on Atheros AR934x SoCs and required for accessing
internal flash storage on routers like Netgear WNDR4300.
This port preserves all NAND programming code while moving platform
configuration to Device Tree and replacing some kernel functions marked
for retirement by 4.19.
Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section).
Most important changes to ar71xx version are:
* old kernel sections of code removed
* 'bool swap_dma' provided by platform data is now set by boolean DT
property 'qca,nand-swap-dma'
* board-supplied (mach-*.c code) platform data removed - its elements
become either unused, redundant or replaced by DT methods (like reset)
* IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore
* calls to deprecated nand_scan_ident() + nand_scan_tail() function pair
replaced by using recommended nand_scan() with attach_chip() callback
* ECC is set to hardware by default, can be overriden by standard DT
'nand-ecc-*' properties (software Hamming or BCH are other options)
This driver has been successfully tested on Netgear WNDR4300 running
experimental ath79 OpenWrt master branch.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[add reset control]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Modify GL-AR300M-Lite and GL-AR300M (NOR):
* Include qca9531_glinet_gl-ar300m.dtsi directly
rather than qca9531_glinet_gl-ar300m-nor.dts
* Remove redundant inclusion of gpio.h and input.h
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
| |
This corrects the additional boardname for the image metadata to the one
used in ar71xx. The previously present additional entry was never used
on a running system.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.
Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
| |
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
| |
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the COMFAST CF-E313AC, an outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio.
Specifications:
- QCA9531 SoC
- 650/400/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps WAN Ethernet, 48V PoE-in
- 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out
- 1x manual pass-through PoE switch
- 64 MB RAM (DDR2)
- 16 MB FLASH
- QCA9886 2T2R 5 GHz 802.11ac, 23 dBm
- 12 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1)
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while the WAN LED flashes, until it starts flashing faster.
Once in failsafe mode, perform a factory reset as usual.
Alternatively, the U-boot bootloader contains a recovery HTTP server
to upload the firmware. Push the reset button while powering the
device on and keep it pressed for >10 seconds. The device's LEDs will
blink several times and the recovery page will be at
http://192.168.1.1; use it to upload the sysupgrade image.
Note:
Four MAC addresses are stored in the "art" partition (read-only):
- 0x0000: 40:A5:EF:AA:AA:A0
- 0x0006: 40:A5:EF:AA:AA:A2
- 0x1002: 40:A5:EF:AA:AA:A1
- 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data)
The stock firmware assigns MAC addresses to physical and virtual
interfaces in a very particular way:
- eth0 corresponds to the physical Ethernet port labeled as WAN
- eth1 corresponds to the physical Ethernet port labeled as LAN
- eth0 belongs to the bridge interface br-wan
- eth1 belongs to the bridge interface br-lan
- eth0 is assigned the MAC from 0x0 (*:A0)
- eth1 is assigned the MAC from 0x1002 (*:A1)
- br-wan is forced to use the MAC from 0x1002 (*:A1)
- br-lan is forced to use the MAC from 0x0 (*:A0)
- radio0 uses the calibration data from 0x5000 (which contains
a valid MAC address, *:A3). However, it is overwritten by the
one at 0x6 (*:A2)
This commit preserves the LAN/WAN roles of the physical Ethernet
ports (as labeled on the router) and the MAC addresses they expose
by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position
of the eth0/eth1 compared to the stock firmware:
- eth0 corresponds to the physical Ethernet port labeled as LAN
- eth1 corresponds to the physical Ethernet port labeled as WAN
- eth0 belongs to the bridge interface br-lan
- eth1 is the interface at @wan
- eth0 is assigned the MAC from 0x0 (*:A0)
- eth1 is assigned the MAC from 0x1002 (*:A1)
- br-lan inherits the MAC from eth0 (*:A0)
- @wan inherits the MAC from eth1 (*:A1)
- radio0's MAC is overwritten to the one at 0x6
This way, eth0/eth1's positions differ from the stock firmware, but
the weird MAC ressignations in br-lan/br-wan are avoided while the
external behaviour of the router is maintained. Additionally, WAN
port is connected to the PHY gmac, allowing to monitor the link
status (e.g., to restart DHCP negotiation when plugging a cable).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches.
Altered patches:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx)
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79)
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
|
|
| |
This addresses several issues in the DTS file:
- add diag LED support
- remove unused node names
- fix whitespace issues
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
| |
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.
This patch fixes them for the ath79 target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches.
Altered patches:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
Compile-tested on: ath79, cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The relationship between GMAC0 and GMAC1 and the kernel devices
eth0 and eth1 was reversed for many ath79 devices by commit 8dde11d521
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
The GL-AR300M-Lite is a single-port device, with the "LAN" port of the
GL-AR300M board unpopulated and its sole port now referenced as eth1,
as a result of commit 8dde11d521. The device was unreachable on
first boot or fresh config.
By changing ð1 (GMAC1) to an MFD, GMAC0 is able to associate with
the phy and is known by the kernel as "eth0".
Thanks to Chuanhong Guo for the suggestion of "simple-mfd"
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Previously, the board name for the GL-AR300M-Lite was incorrect
in 02_network, resulting in an unintended, fall-through condition
when initializing the network configuration.
While builds prior to commit 8dde11d521 (merged June 5, 2019)
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
functioned properly, the error was noted in resolving first-boot
connectivity issues related to the single-phy nature of the device
and the "swap" of eth0 and eth1 related to that commit.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.
With this patch, the variable is not converted before the check,
but only when it's used in dd.
No conversion is done for use in hexdump, as this can deal with
hex value offsets.
Fixes: b133e466b08e ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
If already included in ucidef_add_switch, you do not have to
additionally set the interface mode in ucidef_set_interfaces_*
functions.
This patch removes/adjusts such redundant cases.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches.
Fixes:
- CVE-2019-14814
- CVE-2019-14815
- CVE-2019-14816
- CVE-2019-14821
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
|