| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ADB P.DG A4101N A-000-1A1-AE has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.
Hardware:
* Board ID: 96328avngv
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - Winbond 25Q128BVFG
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43225 Wireless Network Adapter (rev 23)
* LEDs: 1x Power, 1x DSL, 1x Internet, 4x ETH, 1x USB, 1x WLAN, 1x WPS, 1x TEL
* Buttons: 1x Reset, 1x WPS, 1x unnamed
* UART: 1x TTL 115200n8, VCC RX TX GND, on J502 connector
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the cfe boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
A4101N GPIO LAYOUT:
Power always on
DSL GPIO483(03)
Internet GPIO491(11)
ETH1 GPIO505(25)
ETH2 GPIO506(26)
ETH3 GPIO507(27)
ETH4 GPIO508(28)
USB GPIO490(10)
WLAN controlled by BCM43225
WPS GPIO489(09)
TEL GPIO511(31)
Key RESET GPIO503(23)
Key WPS GPIO504(24)
Key unnamed GPIO492(12)
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Amend commit description, DTS improvements, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Like in the previous patches for various targets, this will remove
the "devicename" from LED labels in bcm63xx, as it's useless and
only creates complexity.
The devicename is removed in DTS files and 01_leds, merging
several cases on the way. A migration script is added for
existing configurations.
Note that a few labels were using "model::function" scheme without
color specified, those were converting to just "function" and the
necessary migrations were added to the migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
| |
Support Sercomm firmware partition split.
WFI partition must be defined after bootflag partitions in order for the
parser to properly find bootflag1 and bootflag2 partitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected
to different GPIO PINs in active low configuration.
OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE.
It has different LEDs configuration and flash size/layout
w.r.t the ADB P.DG A4001N A-000-1A1-AX.
Hardware:
* Board ID: 96328avng
* SoC: Broadcom BCM6328
* RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01)
* LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193)
NC GND NC
Installation via CFE:
* Stock CFE has to be overwriten with one for 96328avng boards that can upload
.bin images with no signature check (cfe-A4001N-V0000_96328avng.bin)
* connect a serial port to the board
* Stop the boot process after power on by pressing enter
* set static IP 192.168.1.2 and subnet mask 255.255.255.0
* navigate to http://192.168.1.1/
* upload the OpenWrt image file
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
| |
|
|
|
|
|
|
|
| |
Until now only HW modded SPI flash version was supported.
BCM6328 with 64M RAM and 128M NAND.
More info: https://openwrt.org/toh/sercomm/ad1018
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
