aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/bcm63xx/dts
Commit message (Collapse)AuthorAgeFilesLines
* bcm63xx: R5010UNv2: fix flash partitions for 16MB flashDaniel González Cabanelas2020-07-111-5/+5
| | | | | | | | | | | The router Nucom R5010UN v2 has the partitions defined for a 8MB flash, but the flash chip is 16MB size. We are wasting half of the flash. Fix it and use generic names for partitions. Fixes: 474cde61234c ("brcm63xx: probe SPI flash through DT") Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bcm63xx: AV4202N: add missing PCI pinmuxDaniel González Cabanelas2020-06-221-0/+5
| | | | | | | | | The ADB P.DG AV4202N device has a wifi chipset connected via PCI. But the PCI pinmux is missing and without it the wifi won't work properly. Add the pinctrl_pci to enable the missing PCI pins for this device. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bcm63xx: DGND3700v1: fix port orderDaniel González Cabanelas2020-06-191-4/+4
| | | | | | | | | Fix the switch LAN labels for the DGND3700v1/DGND3800B router, the order is reversed. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> [cut out of bigger patch, adjust commit title/message accordingly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: HG622: enable LAN LEDsDaniel González Cabanelas2020-06-191-1/+3
| | | | | | | | | The Huawei Echolife HG622 has hardware controlled LAN LEDs. Add the ephy led pinctrl to let the router show LAN activity on these LEDs. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bcm63xx: a226m-fwb: fix linux partition offsetDaniel González Cabanelas2020-06-151-4/+4
| | | | | | | | | | | | | | | | | | The Pirelli A226M-FWB has a wrong linux partition offset, caused by a copy-paste error. As of result of this, OpenWrt is currently broken in this unit. Fix it. While at it, also use generic node names and fix the addresses there as well. Fixes: a27d59bb4274 ("brcm63xx: switch to new partition layout specification") Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> [also fix/update node names, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: add support for the Sercomm H500-sDaniel González Cabanelas2020-06-073-0/+224
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sercomm H500-s is an xDSL dual band wireless router based on Broadcom BCM63167 SoC. Hardware: SoC: Broadcom BCM63167 CPU: BMIPS4350 V8.0, 400 MHz, 2 cores Flash: NAND 128 MiB RAM: DDR3 128 MiB Ethernet: 4x 10/100/1000 Mbps Switch: BCM53134S Wireless: 802.11b/g/n: BCM435f (integrated) 802.11ac: Quantenna QT3740BC (onboard SoC) USB: 1x 2.0 LEDs/Buttons: 11x / 2x Flash instruction, web UI: 1. Reset to defaults using the reset button if the admin password is unknown 2. Login into the web UI as admin. Address: http://192.168.0.1 User: admin Password: VF-ESVodafone-H-500-s or l033i-h500s 3. Go to Settings -> Firmware Update, and select the Openwrt factory firmware 4. Update the firmware. 5. Wait until it finish, the device will reboot with Openwrt installed on the alternative image partitions keeping the stock firmware in the former. Notes: - The patch also adds support for the lowi version. Only the factory firmware is different. - The integrated Wifi in the Broadcom Soc isn't still supported. - The Quantenna 802.11ac wifi works ok, but needs to be configured with the Quantenna client application. It can't be configured with Luci nor any iw command since it's a separated subsystem linked via ethernet. - The BCM53134S external switch is managed via MDIO which isn't supported in this target. Therefore it will behave as a dumb switch. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bcm63xx: vr-3032u: add missing compatible propertyÁlvaro Fernández Rojas2020-06-071-1/+1
| | | | | | SoC is a BCM63168. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: vg-8050: add missing compatible propertyÁlvaro Fernández Rojas2020-06-071-1/+1
| | | | | | SoC is a BCM63169. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: vg-8050: fix WFI partition sizeÁlvaro Fernández Rojas2020-06-031-1/+1
| | | | | | Each image can take up to 0x3d60000, which means 128k more per image. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: vr-3032u: fix WFI partition sizeÁlvaro Fernández Rojas2020-06-031-1/+1
| | | | | | Each image can take up to 0x3d60000, which means 128k more per image. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ad1018: add missing partitionsÁlvaro Fernández Rojas2020-06-031-0/+12
| | | | | | This partitions were missing when support for this device was added. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: vg-8050: switch to bcm-wfi-splitÁlvaro Fernández Rojas2020-06-021-5/+5
| | | | | | | Allows to keep a backup firmware in case active firmware is corrupted. Also fix hsspi address warning. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: vr-3032u: switch to bcm-wfi-splitÁlvaro Fernández Rojas2020-06-021-2/+2
| | | | | | Allows to keep a backup firmware in case active firmware is corrupted. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ad1018: switch to Sercomm WFIÁlvaro Fernández Rojas2020-06-021-6/+6
| | | | | | | | Support Sercomm firmware partition split. WFI partition must be defined after bootflag partitions in order for the parser to properly find bootflag1 and bootflag2 partitions. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ar-5315u: expose LEDs through controllerÁlvaro Fernández Rojas2020-05-241-36/+86
| | | | | | | Exposing LEDs through LED controller instead of gpio-leds takes advantage of HW blinking. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ar-5387un: expose LEDs through controllerÁlvaro Fernández Rojas2020-05-241-26/+42
| | | | | | | Exposing LEDs through LED controller instead of gpio-leds takes advantage of HW blinking. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ar-5381u: expose LEDs through controllerÁlvaro Fernández Rojas2020-05-241-19/+34
| | | | | | | Exposing LEDs through LED controller instead of gpio-leds takes advantage of HW blinking. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: add support for ADB P.DG A4001N A-000-1A1-AXDaniele Castro2020-05-221-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI) has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE. It has different LEDs configuration and flash size/layout w.r.t the ADB P.DG A4001N A-000-1A1-AX. Hardware: * Board ID: 96328avng * SoC: Broadcom BCM6328 * RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01) * LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193) NC GND NC Installation via CFE: * Stock CFE has to be overwriten with one for 96328avng boards that can upload .bin images with no signature check (cfe-A4001N-V0000_96328avng.bin) * connect a serial port to the board * Stop the boot process after power on by pressing enter * set static IP 192.168.1.2 and subnet mask 255.255.255.0 * navigate to http://192.168.1.1/ * upload the OpenWrt image file Signed-off-by: Daniele Castro <danielecastro@hotmail.it> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: replace further "ok" with "okay" in DTS filesAdrian Schmutzler2020-05-224-9/+9
| | | | | | | While "ok" is recognized in DT parsing, only "okay" is actually mentioned as valid value. Replace it accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: WIP: add Huawei HG253s v2 supportÁlvaro Fernández Rojas2020-05-211-0/+178
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: dgnd3700-v1: add NAND supportÁlvaro Fernández Rojas2020-05-211-0/+26
| | | | | | | NAND is used as extra storage on this device. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add unmodded SERCOMM AD1018 supportÁlvaro Fernández Rojas2020-05-191-0/+210
| | | | | | | | | Until now only HW modded SPI flash version was supported. BCM6328 with 64M RAM and 128M NAND. More info: https://openwrt.org/toh/sercomm/ad1018 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add Comtrend VG-8050 supportÁlvaro Fernández Rojas2020-05-191-0/+198
| | | | | | | | BCM63169 with 128M RAM, 128M NAND and BCM53125 switch. Switch is connected by HSSPI to CS5. More info: https://openwrt.org/toh/comtrend/vg8050 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add NETGEAR DGND3700v2 supportÁlvaro Fernández Rojas2020-05-191-0/+216
| | | | | | | | BCM6362 with 64M RAM, 32M NAND and BCM53125 switch. Switch is connected by MMAP, which is currently unsupported (no VLANs). More info: https://openwrt.org/toh/netgear/dgnd3700v2 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add support for Comtrend VR-3032uÁlvaro Fernández Rojas2020-05-181-0/+185
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: smp: add NAND supportÁlvaro Fernández Rojas2020-05-184-0/+92
| | | | | | NAND controller is present on BCM6328, BCM6362, BCM6368 and BCM63268. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: replace "ok" with "okay" for status in DTS filesAdrian Schmutzler2020-05-1289-185/+185
| | | | | | | While "ok" is recognized in DT parsing, only "okay" is actually mentioned as valid value. Replace it accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: use generic diag.shAdrian Schmutzler2020-05-1247-49/+377
| | | | | | | | | | | | | | | | This commit removes the target-specific diag.sh script. This way, the generic one is used for the target, which uses DT-aliases to specify the LEDs used. Though generic diag.sh allows to use different LEDs to indicate different states, this patch just moves the old assignment and does not try to "improve" the assignment by using additional colors. However, individual proposals to do so are welcome. For the few cases where status_led2 was used in old diag.sh, only the primary LED was migrated. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* brcm63xx: rename target to bcm63xxAdrian Schmutzler2020-02-1499-0/+10284
This change makes the names of Broadcom targets consistent by using the common notation based on SoC/CPU ID (which is used internally anyway), bcmXXXX instead of brcmXXXX. This is even used for target TITLE in make menuconfig already, only the short target name used brcm so far. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>