aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/bcm63xx/image
Commit message (Collapse)AuthorAgeFilesLines
* treewide: rename IMAGE_PREFIX/IMAGE_NAME to DEVICE_IMG_*Adrian Schmutzler2021-02-251-1/+1
| | | | | | | | | | | | | | We so far had two variables IMG_PREFIX and IMAGE_PREFIX with different content. Since these names are obviously quite confusing, this patch renames the latter to DEVICE_IMG_PREFIX, as it's a device-dependent variable, while IMG_PREFIX is only (sub)target-dependent. For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as that's a device-dependent variable as well. Cc: Paul Spooren <mail@aparcar.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: limit name metadata to model nameÁlvaro Fernández Rojas2021-02-221-5/+1
| | | | | | | Since there are only 16 characters available, on most cases the vendor name will fit in the metadata, but the model name won't fit. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-101-4/+2
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: provide global default for SUPPORTED_DEVICESAdrian Schmutzler2021-01-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The majority of our targets provide a default value for the variable SUPPORTED_DEVICES, which is used in images to check against the compatible on a running device: SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) At the moment, this is implemented in the Device/Default block of the individual targets or even subtargets. However, since we standardized device names and compatible in the recent past, almost all targets are following the same scheme now: device/image name: vendor_model compatible: vendor,model The equal redundant definitions are a symptom of this process. Consequently, this patch moves the definition to image.mk making it a global default. For the few targets not using the scheme above, SUPPORTED_DEVICES will be defined to a different value in Device/Default anyway, overwriting the default. In other words: This change is supposed to be cosmetic. This can be used as a global measure to get the current compatible with: $(firstword $(SUPPORTED_DEVICES)) (Though this is not precisely an achievement of this commit.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: add support for Innacomm W3400V6Sieng Piaw Liew2020-12-091-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Innacomm W3400V6 is an xDSL B/G wireless router based on Broadcom BCM6328 SoC. Hardware: SoC: Broadcom BCM6328 CPU: BMIPS4350 V8.0, 320 MHz, 1 core Flash: SPI-NOR 8MB, MX25L6406E RAM: 64 MB Ethernet: 4x 10/100 Mbps Switch: Integrated Wireless: 802.11b/g, BCM4312 LEDs/Buttons: 9x / 2x Flash instruction, web UI: 1) Set a static IP on your computer compatible with 192.168.1.1, i.e 192.168.1.100 2) Connect the ethernet cable from your computer to the router. 3) Make sure the router is powered off. 4) Press the reset button, don't release it yet! 5) While pressing reset, power on the router. 6) Wait 10 seconds or more. Note: The power LED is red at first then turns to solid green when ready. 8) Release the reset button. 9) Browse to 192.168.1.1 10) Select .bin file. 10) Upgrade the image. 11) Wait for it to reboot. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Ammend commit description, merge patches, DT improvements] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add support for Technicolor TG582nDaniele Castro2020-12-061-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Technicolor TG582n has a similar PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. Hardware: * Board ID: DANT-1 * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L6445EMI * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30) * LEDs: 2x Power, 1x Ethernet, 1x Broadband, 2x Wi-Fi, 2x WPS, 4x ethernet * Buttons: 1x Reset, 1x WPS, 1x WiFi * UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63) Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the CFE boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file PCB: |GPIO: |TG582n: LED2R |488(08) |red Power LED2G |484(04) |green Power LED10R |486(06) | LED13G |485(05) |green Ethernet LED11R |494(14) | LED14G |491(11) |green Broadband LED5R |487(07) |red Internet LED5G |481(01) |green Internet LED12R |498(18) | LED12G |499(19) | LED6R |482(02) |red Wi-Fi LED6G |483(03) |green Wi-Fi LED7R |490(10) |red WPS LED7G |489(09) |green WPS LED4 |508(28) |ethernet port 4 LED3 |507(27) |ethernet port 3 LED9 |506(26) |ethernet port 2 LED8 |505(25) |ethernet port 1 SW3 |503(23) |key Reset SW5 |504(24) |key WPS SW4 |495(15) |key Wi-Fi SW6 |493(13) | SW1 |492(12) | Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [Fix base-files, refresh patch] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add support for Technicolor TG582n Telecom Italia brandedDaniele Castro2020-12-061-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Technicolor TG582n Telecom Italia branded a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGTWI) has the same PCB as the unbranded Technicolor TG582n with LEDs connected to different GPIO PINs in active low configuration and different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one. Hardware: * Board ID: DANT-V * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H * Serial flash: 16 Mbyte - Spansion FL 128SAIF00 * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30) * LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63) Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the CFE boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file PCB: |GPIO: |TG582n: |AGTWI: LED2R |488(08) |red Power |red Power LED2G |484(04) |green Power |green Power LED10R |486(06) | |missing R85 end LED LED13G |485(05) |green Ethernet |green ADSL LED11R |494(14) | |red Internet LED14G |491(11) |green Broadband |green Internet LED5R |487(07) |red Internet |red Wi-Fi LED5G |481(01) |green Internet |green Wi-Fi LED12R |498(18) | |red Service LED12G |499(19) | |green Service LED6R |482(02) |red Wi-Fi |missing R108 end LED LED6G |483(03) |green Wi-Fi |missing R107 end LED LED7R |490(10) |red WPS |missing R91 end LED LED7G |489(09) |green WPS |missing R92 end LED LED4 |508(28) |ethernet port 4 |ethernet port 4 LED3 |507(27) |ethernet port 3 |ethernet port 3 LED9 |506(26) |ethernet port 2 |ethernet port 2 LED8 |505(25) |ethernet port 1 |ethernet port 1 SW3 |503(23) |key Reset |key Reset SW5 |504(24) |key WPS |key Wi-Fi/LED SW4 |495(15) |key Wi-Fi |missing R127 end key SW6 |493(13) | |missing R171 end key SW1 |492(12) | |missing R1 end key Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [DT fixes, base-files fixes and device variant] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add support for ADB P.DG A4101N A-000-1A1-AEDaniele Castro2020-12-061-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4101N A-000-1A1-AE has a similar PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. Hardware: * Board ID: 96328avngv * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25 * Serial flash: 16 Mbyte - Winbond 25Q128BVFG * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43225 Wireless Network Adapter (rev 23) * LEDs: 1x Power, 1x DSL, 1x Internet, 4x ETH, 1x USB, 1x WLAN, 1x WPS, 1x TEL * Buttons: 1x Reset, 1x WPS, 1x unnamed * UART: 1x TTL 115200n8, VCC RX TX GND, on J502 connector Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the cfe boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file A4101N GPIO LAYOUT: Power always on DSL GPIO483(03) Internet GPIO491(11) ETH1 GPIO505(25) ETH2 GPIO506(26) ETH3 GPIO507(27) ETH4 GPIO508(28) USB GPIO490(10) WLAN controlled by BCM43225 WPS GPIO489(09) TEL GPIO511(31) Key RESET GPIO503(23) Key WPS GPIO504(24) Key unnamed GPIO492(12) Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [Amend commit description, DTS improvements, refresh patches] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: Add support for D-Link DSL-2750u rev C1Ahmed Naseef2020-12-051-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the D-Link DSL-2750u rev C1. (https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1) It uses the same hardware as ADB P.DG A4001N. CPU: Broadcom BCM63281 (320 MHz) RAM: 32M (Winbond W9725G6JB) Flash: 8M (MXIC MX25L6445E) Ethernet: 4x 100 Mbps Wireless: 802.11b/g/n: BCM43225 USB: 1x 2.0 Flash instructions: 1. Assign static IP 192.168.1.100 to PC 2. Unplug the power source 3. Press the RESET button at the router, don't release it yet! 4. Plug the power source.Wait some seconds 5. Release the RESET button 6. Browse to http://192.168.1.1 7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and wait some minutes until the firmware upgrade finish. Signed-off-by: Ahmed Naseef <naseefkm@gmail.com> [DTS improvements, proper board patch, refresh patches] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-5/+5
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: add support for the Sercomm H500-sDaniel González Cabanelas2020-06-071-1/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sercomm H500-s is an xDSL dual band wireless router based on Broadcom BCM63167 SoC. Hardware: SoC: Broadcom BCM63167 CPU: BMIPS4350 V8.0, 400 MHz, 2 cores Flash: NAND 128 MiB RAM: DDR3 128 MiB Ethernet: 4x 10/100/1000 Mbps Switch: BCM53134S Wireless: 802.11b/g/n: BCM435f (integrated) 802.11ac: Quantenna QT3740BC (onboard SoC) USB: 1x 2.0 LEDs/Buttons: 11x / 2x Flash instruction, web UI: 1. Reset to defaults using the reset button if the admin password is unknown 2. Login into the web UI as admin. Address: http://192.168.0.1 User: admin Password: VF-ESVodafone-H-500-s or l033i-h500s 3. Go to Settings -> Firmware Update, and select the Openwrt factory firmware 4. Update the firmware. 5. Wait until it finish, the device will reboot with Openwrt installed on the alternative image partitions keeping the stock firmware in the former. Notes: - The patch also adds support for the lowi version. Only the factory firmware is different. - The integrated Wifi in the Broadcom Soc isn't still supported. - The Quantenna 802.11ac wifi works ok, but needs to be configured with the Quantenna client application. It can't be configured with Luci nor any iw command since it's a separated subsystem linked via ethernet. - The BCM53134S external switch is managed via MDIO which isn't supported in this target. Therefore it will behave as a dumb switch. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bcm63xx: image: support device-specific load addressÁlvaro Fernández Rojas2020-06-071-12/+10
| | | | | | | Some CFEs are located at the address currently used for relocation and lzma loader load address, so we need to provide a way to override it. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: image: don't add the CFE to the sercomm factoryDaniel González Cabanelas2020-06-071-12/+0
| | | | | | | | | | | | | | | There is no need to include the CFE bootloader in the Sercomm factory images. There might be a case when this could be useful: - We are running the stock firmware on the first Sercomm image - The second partition storing the botloader was erased (unlikely) Even in this case flashing an image without a bootlader is harmless. Don't include the bootloader in the factory image creation and rid of the risk of flashing factory images with an untested bootloader partition. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bcm63xx: lzma-loader: allow bigger ramdisksÁlvaro Fernández Rojas2020-06-032-4/+6
| | | | | | | | | | | | | | | | Some (older) CFEs are loaded at 0x80401000 and ramdisks are loaded at 0x80010000, which means that ramdisk size limit is 0x3F1000 (almost 4M). Therefore, current ramdisks (~4MB) are overwritting CFE in these devices, which results in a crash. This commit changes the address where ramdisks are loaded to 0x80a00000, which is the same address where kernel is loaded when booting from the flash. Therefore, lzma-loader will now be loaded at 0x80a00000, but it will still decompress the kernel at 0x80010000. Tested with huawei,hg556a-b, which has its CFE loaded at 0x80401000. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ad1018: remove cfe.bin image supportÁlvaro Fernández Rojas2020-06-032-27/+1
| | | | | | | | | | | | Apparently, Sercomm allows loading a BCM WFI image via CFE, but this image destroys "serial" and "protect" nand partitions, which is wrong. It will also set both bootflags to the same value, which causes booting issues with cferam (cferom will alternatively boot from cferam1 or cferam2 each time the device is rebooted). Now that OEM Sercomm images are supported it's time to remove this hacky cfe.bin image support. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: stop using legacy lzma for all devicesÁlvaro Fernández Rojas2020-06-031-54/+59
| | | | | | | | | BCM6368 and newer devices are compatible with any lzma compression parameters. Add a new legacy device definition and use it on BCM6358 and older devices. Compressed kernel size is reduced by ~1.35%. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: vg-8050: switch to bcm-wfi-splitÁlvaro Fernández Rojas2020-06-021-1/+1
| | | | | | | Allows to keep a backup firmware in case active firmware is corrupted. Also fix hsspi address warning. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: vr-3032u: switch to bcm-wfi-splitÁlvaro Fernández Rojas2020-06-021-1/+1
| | | | | | Allows to keep a backup firmware in case active firmware is corrupted. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: nand: order devices alphabeticallyÁlvaro Fernández Rojas2020-06-021-10/+10
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: nand: add CFE_WFI_VERSION values for each deviceÁlvaro Fernández Rojas2020-06-021-1/+5
| | | | | | CFE_WFI_VERSION should be defined per device instead of using a generic value. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: nand: sercomm: switch to sercomm-load scriptÁlvaro Fernández Rojas2020-06-021-5/+6
| | | | | | | xxd is not a valid dependency and shouldn't be used. Fixes buildbot failure. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ad1018: support Sercomm factory imagesÁlvaro Fernández Rojas2020-06-021-1/+11
| | | | | | | This images can be flashed from the official firmware, as opposed to CFE images, which can only be flashed from CFE and require opening the case. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: nand: support Sercomm firmwaresÁlvaro Fernández Rojas2020-06-022-0/+67
| | | | | | Add support for Sercomm factory firmwares (AES 256 CBC encrypted). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: add support for ADB P.DG A4001N A-000-1A1-AXDaniele Castro2020-05-221-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI) has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE. It has different LEDs configuration and flash size/layout w.r.t the ADB P.DG A4001N A-000-1A1-AX. Hardware: * Board ID: 96328avng * SoC: Broadcom BCM6328 * RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01) * LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193) NC GND NC Installation via CFE: * Stock CFE has to be overwriten with one for 96328avng boards that can upload .bin images with no signature check (cfe-A4001N-V0000_96328avng.bin) * connect a serial port to the board * Stop the boot process after power on by pressing enter * set static IP 192.168.1.2 and subnet mask 255.255.255.0 * navigate to http://192.168.1.1/ * upload the OpenWrt image file Signed-off-by: Daniele Castro <danielecastro@hotmail.it> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: WIP: add Huawei HG253s v2 supportÁlvaro Fernández Rojas2020-05-211-0/+22
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: nand: support CFE partition tagsÁlvaro Fernández Rojas2020-05-212-0/+22
| | | | | | | | Introduce support for generating JFFS2 CFE partition tags. This is used in NAND devices in order to verify the integrity of the JFFS2 partition. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: lzma-loader: rely on CHIP_ID for UART addressÁlvaro Fernández Rojas2020-05-205-83/+32
| | | | | | | | lzma-loader uart output wasn't working on BCM3380/BCM6362 because these SoCs have the same processor ID. Let's use CHIP_ID for establishing the UART base address. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: lzma-loader: remove unused definitionsÁlvaro Fernández Rojas2020-05-202-22/+1
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: image: add CVG834G CHIP_IDÁlvaro Fernández Rojas2020-05-201-1/+1
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: image: rename CFE_CHIP_ID to CHIP_IDÁlvaro Fernández Rojas2020-05-203-101/+101
| | | | | | Rename CFE_CHIP_ID to a generic name that doesn't involve CFE. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add unmodded SERCOMM AD1018 supportÁlvaro Fernández Rojas2020-05-192-0/+43
| | | | | | | | | Until now only HW modded SPI flash version was supported. BCM6328 with 64M RAM and 128M NAND. More info: https://openwrt.org/toh/sercomm/ad1018 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add Comtrend VG-8050 supportÁlvaro Fernández Rojas2020-05-191-0/+17
| | | | | | | | BCM63169 with 128M RAM, 128M NAND and BCM53125 switch. Switch is connected by HSSPI to CS5. More info: https://openwrt.org/toh/comtrend/vg8050 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add NETGEAR DGND3700v2 supportÁlvaro Fernández Rojas2020-05-191-0/+17
| | | | | | | | BCM6362 with 64M RAM, 32M NAND and BCM53125 switch. Switch is connected by MMAP, which is currently unsupported (no VLANs). More info: https://openwrt.org/toh/netgear/dgnd3700v2 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add support for Comtrend VR-3032uÁlvaro Fernández Rojas2020-05-181-0/+18
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: smp: add NAND supportÁlvaro Fernández Rojas2020-05-182-0/+123
| | | | | | NAND controller is present on BCM6328, BCM6362, BCM6368 and BCM63268. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: image: remove unused definitionÁlvaro Fernández Rojas2020-05-141-2/+1
| | | | | | KERNEL_ENTRY isn't used by lzma-loader. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: loader-lzma: use default lzmaÁlvaro Fernández Rojas2020-05-122-10/+6
| | | | | | Specific CFE LZMA parameters aren't needed for LZMA Loader. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: image: rename LOADADDR to KERNEL_LOADADDRÁlvaro Fernández Rojas2020-05-121-9/+8
| | | | | | Also remove KERNEL_ENTRY, since it's the same as KERNEL_LOADADDR Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: disable all devices with <= 4MiB flash and <= 32 MiB RAMJonas Gorski2020-04-121-0/+11
| | | | | | | | | | | Device with 4 MiB flash and 32 MiB RAM won't be able to run OpenWrt in a sufficient manner without tweaks, so don't build images for them by default. This includes all BCM6338, BCM6345 and BCM6348 "generic" devices, as there are no supported devices of these with more than that. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* treewide: gather DEVICE_VARS into one placeSungbo Eo2020-03-211-5/+6
| | | | | | | | | | | Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* brcm63xx: rename target to bcm63xxAdrian Schmutzler2020-02-1421-0/+3408
This change makes the names of Broadcom targets consistent by using the common notation based on SoC/CPU ID (which is used internally anyway), bcmXXXX instead of brcmXXXX. This is even used for target TITLE in make menuconfig already, only the short target name used brcm so far. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>