| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
| |
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
SVN-Revision: 26959
|
| |
|
|
|
|
| |
Signed-off-by: Adrian Feliks <mexit@o2.pl>
SVN-Revision: 26958
|
| |
|
|
|
|
|
|
| |
This patch adds support for D-Link's DVA-G3810BN/TL product.
Signed-off-by: Roman Dumycz <roman@secureas.com>
SVN-Revision: 26956
|
| |
|
|
| |
SVN-Revision: 26954
|
| |
|
|
|
|
|
|
|
| |
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26878
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26876
|
| |
|
|
|
|
| |
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26875
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
I wrote a patch to add 96348SV board (aka MAGIC) support to trunk.
In my case I've found it in a Telsey "Alice W-Gate" router, fairly common
(in the past) in Italy.
I used the board definition (GPIOs, leds, ...) from the Broadcom GPL-2
relased code (here is a mirror: http://beghiero.myftp.org/sorgenti/boardparms.c )
Thanks to KanjiMonster for the support on the IRC channel.
Signed-off-by: Laurento Frittella <laurento.frittella@gmail.com>
SVN-Revision: 25584
|
| |
|
|
|
|
|
|
| |
The device is called SPW500V, not SP500W.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 25431
|
| |
|
|
|
|
|
|
| |
devices that need it.
Signed-off-by: Daniel Dickinson <daniel@cshore.neomailbox.net>
SVN-Revision: 24836
|
| |
|
|
|
|
| |
96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network.
SVN-Revision: 24442
|
| |
|
|
|
|
| |
(4-port switch)
SVN-Revision: 24273
|
| |
|
|
|
|
|
|
|
|
| |
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24190
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24188
|
| |
|
|
|
|
|
|
|
|
|
| |
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24187
|
| |
|
|
|
|
|
|
|
|
|
| |
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24185
|
| |
|
|
|
|
| |
left on, not off
SVN-Revision: 22466
|
| |
|
|
| |
SVN-Revision: 21627
|
| |
|
|
|
|
| |
state from userspace
SVN-Revision: 16892
|
| |
|
|
| |
SVN-Revision: 16887
|
|
|
SVN-Revision: 13362
|
