aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/generic/files/drivers
Commit message (Collapse)AuthorAgeFilesLines
* generic: platform/mikrotik: fix incorrect testThibaut VARÈNE2020-08-181-1/+1
| | | | | | The test is meant to check the result of the preceding kmalloc() Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* treewide: rename POWER_ON_STRIP registerSungbo Eo2020-07-252-11/+11
| | | | | | | | | | AR8327 datasheet[1] calls the register at address 0x0010 "Power-on Strapping Register". As it has nothing to do with "strip", let's rename it to "POWER_ON_STRAP" to make it easier to grasp. [1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: mtdsplit_uimage: add SGE parserMathieu Martin-Borret2020-07-131-0/+38
| | | | | | | Adding SGE parser for SGE (T&W) Shenzhen Gongjin Electronics to add 96 bytes padding the the firmware image Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
* generic: platform/mikrotik: add partial AR71xx cpufreq supportThibaut VARÈNE2020-07-081-28/+71
| | | | | | | | This patch adds cpu frequency setting for AR724x and AR7161. It is unknown if all the AR71xx devices support the same value range, so support is only enabled for AR7161 at this stage. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: add board_revision tagThibaut VARÈNE2020-07-081-1/+6
| | | | | | Tag was discovered exploring the hard_config of a "r2" board. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: graceful fallback for cpufreq_indexThibaut VARÈNE2020-07-081-9/+12
| | | | | | | | | | The current code would return an error on ath79 when the SoC isn't known to the driver. Return the raw hex value instead, as happens with non supported targets. Also return the correctly incremented value from sc_tag_cpufreq_ath79_arraysize() Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: match RouterBOOT nomenclatureThibaut VARÈNE2020-07-081-18/+19
| | | | | | | RouterBOOT cpu frequency settings are letter-indexed. Follow the same logic for the sysfs interface. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: fix routerboot_tag_show_u32s()Thibaut VARÈNE2020-07-081-5/+5
| | | | | | | The routine would only accurately print out the first word. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Fixes: 5ecf7d96 ("generic: routerboot sysfs platform driver")
* kernel: rtl8367b: fix external interface modesINAGAKI Hiroshi2020-06-111-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The interface mode number of RGMII_33V is 7 on RTL8367, but it's 9 on RTL8367B. the external interface modes for RTL8367 are follows: - 0, Disabled - 1, RGMII - 2, MII_MAC - 3, MII_PHY - 4, TMII_MAC - 5, TMII_PHY - 6, GMII - 7, RGMII_33V the external interface modes for RTL8367B are follows: - 0, Disabled - 1, RGMII - 2, MII_MAC - 3, MII_PHY - 4, TMII_MAC - 5, TMII_PHY - 6, GMII - 7, RMII_MAC - 8, RMII_PHY - 9, RGMII_33V But the driver in U-Boot of RT-N56U GPL tar blocks using RGMII_33V (9) mode and it seems to be unsupported on RTL8367B, so drop it from switch-case in rtl8367b_extif_set_mode. ref (RTL8367): - TL-WR2453ND v1 ref (RTL8367B): - ASUS RT-N56U - TP-Link Archer C2 v1 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: b53: fix compilation with kernels 5.5+Rafał Miłecki2020-06-051-0/+8
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: mtdsplit: bcm_wfi: always add img partitionsÁlvaro Fernández Rojas2020-06-031-9/+44
| | | | | | | | | This is useful when booting OpenWrt from ramdisks in order to have both images partitions defined. Furthermore, instead of always using img2 for the inactive image, let's use img1 or img2 accordingly. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: support Broadcom WFI bootflagsÁlvaro Fernández Rojas2020-06-021-0/+110
| | | | | | | | When firmware is flashed, cferam.000 extension is renamed to the next number. When booting, CFE scans the NAND and picks the partition with the highest cferam extension and ignores the other one. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: improve JFFS2 scanÁlvaro Fernández Rojas2020-06-021-6/+20
| | | | | | Allow retrieving full file name and length by parameters. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: bcm_wfi: refactor codeÁlvaro Fernández Rojas2020-06-021-82/+69
| | | | | | Create new parse_bcm_wfi function with common code from current parsers. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: bcm_wfi: remove brcm,wfi-sercomm compatibilityÁlvaro Fernández Rojas2020-06-021-2/+1
| | | | | | | The only Sercomm WFI user has been migrated to a dedicated firmware parser. Keep support for no cferam partition based on a boolean DT property. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: bcm_wfi: support Sercomm bootflagsÁlvaro Fernández Rojas2020-06-021-0/+148
| | | | | | | | Sercomm uses 2 bootflag partitions and boots the firmware with the highest bootflag. Support splitting the firmware partition while keeping support for unsplitted layout. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: bcm_wfi: code refactoringÁlvaro Fernández Rojas2020-06-021-15/+18
| | | | | | | | - Rename master to mtd. - Pass mtd size as an argument. - Rename of_match_table. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* generic: routerboot sysfs: soft_config support for ath79 cpufreqThibaut VARÈNE2020-05-281-2/+64
| | | | | | | | | | | | This commit introduces support for R/W access to the CPU frequency setting of routerboot on ath79 hardware. On unsupported hardware, the sysfs attribute will expose the raw tag value (read-only) to help with reverse engineering its meaning. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs: move tag_show_u32()Thibaut VARÈNE2020-05-283-22/+23
| | | | | | | | This routine will be shared between hard and soft config drivers. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs: add support for soft_configThibaut VARÈNE2020-05-286-2/+711
| | | | | | | | | | | | | | | | | | | This driver exposes the data encoded in the "soft_config" flash segment of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder named "soft_config" through a set of human-and-machine-parseable attributes. Changes can be discarded by writing 0 to the 'commit' attribute, or they can be committed to flash storage by writing 1. This driver does not reuse any of the existing code previously found in the "rbcfg" utility and makes this utility obsolete by providing a clean sysfs interface. Like "rbcfg", this driver requires 4K_SECTORS support since the flash partition in which these parameters are stored is typically 4KB in size. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs: move tag_show_string()Thibaut VARÈNE2020-05-283-11/+15
| | | | | | | | | This routine will be shared between hard and soft config drivers. Also use scnprintf() instead of snprintf(). Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: rb_hardconfig.c minor fixesThibaut VARÈNE2020-05-281-7/+14
| | | | | | | | | | | | | For the sake of strictly typed code, add a missing const qualifier. Add a missing return value in error path. Check the return value of mtd_read(), for good measure. Also demote the error printks of failed sysfs file creation to warn level since they are not fatal in the init() sequence. Finally, add a note regarding PAGE_SIZE and clarify a comment. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: reorder KconfigThibaut VARÈNE2020-05-281-2/+2
| | | | | | | | | The depends and select should apply to the sysfs driver, not the meta config. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: disambiguate SPDX-License-IdentifierThibaut VARÈNE2020-05-203-3/+3
| | | | | | I meant it to be GPL-2.0-only, as evidenced by the boilerplate. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerbootpart.c: disambiguate SPDX-License-IdentifierThibaut VARÈNE2020-05-201-1/+1
| | | | | | I meant it to be GPL-2.0-only, as evidenced by the boilerplate. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* kernel: mtdsplit: bcm_wfi: add sercomm supportÁlvaro Fernández Rojas2020-05-191-23/+47
| | | | | | SERCOMM creates separates partitions for cferam. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: add BCM WFI supportÁlvaro Fernández Rojas2020-05-183-0/+209
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* generic: drop outdated kernel version switches in local driversAdrian Schmutzler2020-05-175-51/+3
| | | | | | | This drops the obsolete version switches for non-supported kernels from local drivers in generic target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* generic: platform/mikrotik: fix LZOR supportThibaut VARÈNE2020-05-161-21/+36
| | | | | | | | | | | | 31e99fe3da which introduced this code was unfortunately untested. This commit fixes a number of issues and works around the fact that in this particular scheme, the LZO payload may be padded at the end which will trigger a harmless lzo decompression error. This commit also disambiguates the debug printks. Tested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Fixes: 31e99fe3da ("generic: platform/mikrotik: support LZOR encoding")
* generic: add MikroTik hw bit descriptionKoen Vandeputte2020-05-111-0/+1
| | | | | | | | | An e-mail response from MikroTik contained a minimal overview on hardware option bits which mentioned a currently unknown bit. While not being too detailed what it does, add it for documentation purposes. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* generic: platform/mikrotik: support LZOR encodingThibaut VARÈNE2020-05-081-1/+261
| | | | | | | | Some newer MikroTik RouterBOARD devices use a new encoding scheme for their WLAN calibration data. This patch provides support for decoding this new scheme. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs platform driverThibaut VARÈNE2020-05-085-0/+717
| | | | | | | | | | | | | | | | | | | | | | | | | This driver exposes the data encoded in the "hard_config" flash segment of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder named "hard_config". The WLAN calibration data is available on demand via the 'wlan_data' sysfs file in that folder. This driver permanently allocates a chunk of RAM as large as the "hard_config" MTD partition (typically 4KB), although it is technically possible to operate entirely from the MTD device without using a local buffer (except when requesting WLAN calibration data), at the cost of a performance penalty. This driver does not reuse any of the existing code previously found in routerboot.c. This driver has been successfully tested on BE (ath79) and LE (ipq40xx and ramips) hardware. Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Tested-by: Baptiste Jonglez <git@bitsofnetworks.org> Tested-by: Tobias Schramm <t.schramm@manjaro.org> Tested-by: Christopher Hill <ch6574@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerbootpart MTD parser for RouterBootThibaut VARÈNE2020-05-081-0/+365
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver provides an OF MTD parser to properly assign the RouterBoot partitions on the flash. This parser builds from the "fixed-partitions" one (see ofpart.c), but it can handle dynamic partitions as found on routerboot devices. The parent node must contain the following: compatible = "mikrotik,routerboot-partitions"; #address-cells = <1>; #size-cells = <1>; Children routerbootpart DTS nodes are defined as follows: For fixed partitions node-name@unit-address { reg = <prop-encoded-array>; label = <string>; read-only; lock; }; All properties but reg are optional. For dynamic partitions: node-name { size = <prop-encoded-array>; label = <string>; read-only; lock; }; size property is mandatory unless the next partition is a fixed one or a "well-known" one (matched from the strings defined below) in which case it can be omitted or set to 0; other properties are optional. By default dynamic partitions are appended after the preceding one, except for "well-known" ones which are automatically located on flash. Well-known partitions (matched via label or node-name): - "hard_config" - "soft_config" - "dtb_config" This parser requires the DTS to list partitions in ascending order as expected on the MTD device. This parser has been successfully tested on BE (ath79) and LE (ipq40xx and ramips) hardware. Tested-by: Baptiste Jonglez <git@bitsofnetworks.org> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Tested-by: Tobias Schramm <t.schramm@manjaro.org> Tested-by: Christopher Hill <ch6574@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: ar8216: fix unknown packet flooding for ar8229/ar8236Chuanhong Guo2020-05-062-7/+16
| | | | | | | | | | | | ar8229 and ar8236 don't allow unknown unicast/multicast frames and broadcast frames to be flooded to cpu port. This isn't desired behavior for swconfig as we treat it as a standalone switch. Current code doesn't enable unicast frame flooding for ar8229 and uses wrong setup for ar8236. This commit fixes both of them by enabling port 0 flooding for all unknown frames. Fixes: FS#2848 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: fix include of myloader.o since kernel 5.4Adrian Schmutzler2020-04-241-182/+0
| | | | | | | | | | | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Based on this, the selection of myloader.o in OpenWrt was also moved to that subdirectory, while the Kconfig and our local myloader.c file remained in /drivers/mtd. This resulted in linking errors like the following (on ath25@5.4): make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ... needed by 'drivers/mtd/parsers/built-in.a'. Stop. make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2 make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2 Since myloader.c is not too big, this patch moves it to the kernel patches, allowing to adjust the path for kernel 5.4 and keeping Makefiles and file paths better in sync. Other patches have been refreshed accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: rtl8367b: use id as a bit offset for BYPASS_LINE_RATEINAGAKI Hiroshi2020-04-041-4/+2
| | | | | | | | | | | | | | | | | In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the devices with this switch directly uses the ID of external interface as a bit offset. We should use the same way. ref (RTL8367B): - ASUS RT-N56U - TP-Link Archer C2 v1 ref (RTL8367): - TP-Link TL-WR2543ND v1 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: rtl8367b: fix DEBUG register address for extif2INAGAKI Hiroshi2020-04-041-1/+1
| | | | | | | | RTL8367B_CHIP_DEBUG1_REG (0x1304) is for external interface 1. For external interface 2, use RTL8367B_CHIP_DEBUG2_REG (0x13e2) instead. Fixes: 9801d61c4a ("kernel: rtl8367b: add configuration for extif2") Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: rtl8367b: add configuration for extif2Serge Vasilugin2020-03-211-5/+42
| | | | | | | | | | | | | | | | | | | | | | Both rtl8367b and rtl8367s have two extended interface rtl8367rb: 5 port + 2*RGMII/MII rtl8367s: 5 port + SGMII/HSGMI + RGMII/MII (?)rtl8367sb: 5 port + 2*RGMII/MII These interfaces correspond to EXT1 and EXT2 (ports 6 and 7 respectivly). This patch allow to configure EXT2 in dts-file: rtl8367rb { compatible = "realtek,rtl8367b"; cpu_port = <7>; realtek,extif2 = <1 0 1 1 1 1 1 1 2>; mii-bus = <&mdio0>; phy_id = <29>; }; Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> [fix indent, replace magic value, alter commit message] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* generic: rtl8367b: add definition of debug regChuanhong Guo2020-03-211-5/+30
| | | | | | | This commit adds definition of DEBUG0 and DEBUG1 registers and replace magic values with proper register modifying. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* generic: make all phy drivers kernel 5.0 compatibleMathias Kresin2020-03-163-0/+21
| | | | | | | | It adjusts the code to upstream changes from the commit 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode") Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: add support for kernel 5.4Koen Vandeputte2020-02-281-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following patches were removed because they are integrated in the upstream kernel 5.4: * backport-5.4/047-v4.21-mtd-keep-original-flags-for-every-struct-mtd_info.patch * backport-5.4/048-v4.21-mtd-improve-calculating-partition-boundaries-when-ch.patch * backport-5.4/080-v5.1-0001-bcma-keep-a-direct-pointer-to-the-struct-device.patch * backport-5.4/080-v5.1-0002-bcma-use-dev_-printing-functions.patch * backport-5.4/095-Allow-class-e-address-assignment-via-ifconfig-ioctl.patch * backport-5.4/101-arm-cns3xxx-use-actual-size-reads-for-PCIe.patch * backport-5.4/200-v5.2-usb-dwc2-Set-lpm-mode-parameters-depend-on-HW-configuration.patch * backport-5.4/210-arm64-sve-Disentangle-uapi-asm-ptrace.h-from-uapi-as.patch * backport-5.4/380-v5.3-net-sched-Introduce-act_ctinfo-action.patch * backport-5.4/450-v5.0-mtd-spinand-winbond-Add-support-for-W25N01GV.patch * backport-5.4/451-v5.0-mtd-spinand-Add-initial-support-for-Toshiba-TC58CVG2.patch * backport-5.4/452-v5.0-mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch * backport-5.4/455-v5.1-mtd-spinand-Add-support-for-all-Toshiba-Memory-produ.patch * backport-5.4/456-v5.1-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch * backport-5.4/460-v5.0-mtd-spi-nor-Add-support-for-mx25u12835f.patch * backport-5.4/460-v5.3-mtd-spinand-Define-macros-for-page-read-ops-with-thr.patch * backport-5.4/461-v5.3-mtd-spinand-Add-support-for-two-byte-device-IDs.patch * backport-5.4/462-v5.3-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UFxxG.patch * backport-5.4/463-v5.3-mtd-spinand-Add-initial-support-for-Paragon-PN26G0xA.patch * backport-5.4/700-v5.1-net-phylink-only-call-mac_config-during-resolve-when.patch * backport-5.4/701-v5.2-net-phylink-ensure-inband-AN-works-correctly.patch * backport-5.4/702-v4.20-net-ethernet-Add-helper-for-MACs-which-support-asym-.patch * backport-5.4/703-v4.20-net-ethernet-Add-helper-for-set_pauseparam-for-Asym-.patch * backport-5.4/704-v4.20-net-phy-Stop-with-excessive-soft-reset.patch * backport-5.4/705-v5.1-net-phy-provide-full-set-of-accessor-functions-to-MM.patch * backport-5.4/706-v5.1-net-phy-add-register-modifying-helpers-returning-1-o.patch * backport-5.4/707-v5.1-net-phy-add-genphy_c45_check_and_restart_aneg.patch * backport-5.4/708-v5.3-net-phylink-remove-netdev-from-phylink-mii-ioctl-emu.patch * backport-5.4/709-v5.3-net-phylink-support-for-link-gpio-interrupt.patch * backport-5.4/710-v5.3-net-phy-allow-Clause-45-access-via-mii-ioctl.patch * backport-5.4/711-v5.3-net-sfp-add-mandatory-attach-detach-methods-for-sfp-.patch * backport-5.4/712-v5.3-net-sfp-remove-sfp-bus-use-of-netdevs.patch * backport-5.4/713-v5.2-net-phylink-avoid-reducing-support-mask.patch * backport-5.4/714-v5.3-net-sfp-Stop-SFP-polling-and-interrupt-handling-duri.patch * backport-5.4/715-v5.3-net-phylink-don-t-start-and-stop-SGMII-PHYs-in-SFP-m.patch * backport-5.4/740-v5.5-net-phy-avoid-matching-all-ones-clause-45-PHY-IDs.patch * backport-5.4/741-v5.5-net-phylink-fix-link-mode-modification-in-PHY-mode.patch * pending-5.4/103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch * pending-5.4/131-spi-use-gpio_set_value_cansleep-for-setting-chipsele.patch * pending-5.4/132-spi-spi-gpio-fix-crash-when-num-chipselects-is-0.patch * pending-5.4/220-optimize_inlining.patch * pending-5.4/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch * pending-5.4/475-mtd-spi-nor-Add-Winbond-w25q128jv-support.patch * pending-5.4/477-mtd-add-spi-nor-add-mx25u3235f.patch * pending-5.4/479-mtd-spi-nor-add-eon-en25qh64.patch Some bigger changes were done to this feature and we did not port this patch yet: * hack-5.4/207-disable-modorder.patch This depends on BOOTMEM which was removed from the kernel, this needs some bigger changes: * hack-5.4/930-crashlog.patch A different version of the FPU disable patch was merged upstream, OpenWrt needs some adaptations. * pending-5.4/304-mips_disable_fpu.patch - no crashlog support yet as a required file got deleted upstream - Removed patch below, which is now seen as a recursive dependency [1] - Removed patch below due to build error [2] - fix still required to avoid identical function def [3] - Fixes included from Blocktrron - Fixes included from Chunkeey - Fix included from nbd regarding "dst leak in Flow Offload" [1] target/linux/generic/hack-5.4/260-crypto_test_dependencies.patch [2] target/linux/generic/hack-5.4/207-disable-modorder.patch [3] target/linux/generic/pending-5.4/613-netfilter_optional_tcp_window_check.patch Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: swconfig: make compatible with kernel 5.2Mathias Kresin2020-02-121-6/+41
| | | | | | | | | | | | | | | | | | | | | Since kernel 5.2 within netlink messages the NLA_F_NESTED nested flag is validated. But swconfig/swlib doesn't set the flag for SWITCH_ATTR_OP_VALUE_PORTS related netlink messages and assigning ports to vlans via swconfig dev switch0 vlan 1 set ports '0 1 2 3 4 6t' Errors put with "Failed to set attribute: Invalid input data or parameter". Relax the validation rules and use the deprecated functions, to use the same level of validation as it was till kernel 5.1. Depending on who has swconfig related netlink messages implemented, there might be more broken tools out there and we should keep backward compatibility if possible. Signed-off-by: Mathias Kresin <dev@kresin.me> Tested-by: Rafał Miłecki <rafal@milecki.pl>
* swconfig: fix Broadcom b53 supportTobias Schramm2020-01-122-0/+33
| | | | | | | | | This commit fixes a bug in the main swconfig patch where a function needed by the b53 driver is not exported. Additionally it adds OF support to the b53_mdio driver for devicetree- based probing Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* generic ar8xxx: increase VLAN table for AR83x7David Bauer2019-11-303-9/+13
| | | | | | | | | | | | The Atheros AR8327 and AR8337 have (according to their datasheet) a VLAN table with a maximum of 4096 entries. Currently, there's a hard limit of 128 VLANs, which is the same as for most other Atheros switches. Increase this limit only for the AR83x7 series and modify some shared functions to allow them to work with a variable max VLAN count. Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: switch to upstream owl-loader driverChristian Lamparter2019-11-301-246/+0
| | | | | | | | | | | | | | | | | | The Owl Loader (named after the codename that Atheros gave these devices back in the day) has been accepted upstream. This patch removes the "misc" driver OpenWrt had and adds the remaining differences against the version that ships with 5.4-rc1 into a separate "120-owl-loader-compat.patch" file that can be cut down once AR71XX is being dealt with. Note: I decided to keep the existing (kmod-)owl-loader package name around for now. The kernel module file in the kmod package will be called ath9k_pci_owl_loader.ko though. Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: fix swconfig compilation with kernels 5.2+Rafał Miłecki2019-10-281-0/+23
| | | | | | | This is related to the upstream kernel change 3b0f31f2b8c9 ("genetlink: make policy common to family"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: Fix off-by-one error in FIT mtd partition search.Oldřich Jedlička2019-10-091-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This fixes off-by-one error introduced in commit dc76900021b8 ("kernel: Correctly search for the FIT image in mtd partition.") Function `mtd_read` starts reading at `offset` and needs `hdr_len` number of bytes to be available. Suppose the easiest case when `offset` is `0` and `hdr_len` equals to `mtd->size` - the `for` loop will not be entered even when enough bytes are available to be read. Same happens for any non-zero `offset`, when `hdr_len` is just enough bytes to be read until `mtd->size` is reached. Imagine that for example `mtd->size=5`, `offset=4` and `hdr_len=1`. Then `offset+hdr_len=5` and the check has to be `offset+hdr_len <= mtd->size`, i.e. `5 <= 5`. The check for `offset + hdr_len` value needs to be inclusive, therefore use `<=`. Fixes: dc76900021b8 ("kernel: Correctly search for the FIT image in mtd partition.") Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com> [adjusted commit ref, fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: Correctly search for the FIT image in mtd partition.Fredrik Olofsson2019-09-191-2/+2
| | | | | | Previously all iterations of the loop checked offset=0 in the partition. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
* kernel: mtdsplit_uimage: add support for okli imageChuanhong Guo2019-08-081-0/+58
| | | | | | | | | | This adds support for uImage used by OpenWrt kernel loader. The parser searches for uImage header at flash eraseblock boundary and it might attempt to split any firmware with loader, therefore this entry doesn't have MTD_PARSER_TYPE_FIRMWARE so that this parser is only used when explicitly defined in dts. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: drop Fon(Foxconn) parser matching for the "firmware" partitionRafał Miłecki2019-08-061-1/+0
| | | | | | | | | | | | | | | | This parser's matching function appears to be too generic as it matches e.g. Buffalo WZR-HP-G300NH. That results in incorrect parts parsing. Luckily this parser is needed by Fon FON2601 only which uses DT-based ramips target. It means we can depend on mtd subsystem matching of "fonfxc,uimage" string. That said triggering this parser based on the "firmware" (or whatever MTD_SPLIT_FIRMWARE_NAME is) partiiton name is not needed. It can be dropped which will automatically fix the Buffalo WZR-HP-G300NH case. Fixes: a1c6a316d299 ("ramips: add support for Fon FON2601") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-19 18:20:06 +0000