aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/base-files/etc/board.d
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: enable Linksys EA8500 eth1 interfacePawel Dembicki2020-07-111-1/+1
| | | | | | | | | | | | | At this moment Linksys EA8500 uses only eth0. This patch change switch registers, which allow to use eth1 as lan and eth0 as wan. The method work with similar Linksys EA7500V1 and it work with EA8500. Suggested-by: Sungbo Eo <mans0n@gorani.run> Tested-by: Brian Onn <brian.a.onn@gmail.com> Tested-by: Adrian Panella <ianchi74@outlook.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq806x: add support for Linksys EA7500 V1Pawel Dembicki2020-07-081-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Linksys EA7500 V1 router. Specification: - CPU: Qualcomm IPQ8064 - RAM: 256MB - Flash: NAND 128MB - WiFi: QCA9982 an+ac + QCA9983 bgn - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337) - USB: 1x USB 3.0 1x USB2.0 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level) - 2 Buttons - 1 LED Known issues: - Some devices won't flash via web gui Installation: - Newer stock images doesn't allow to install custom firmware. - Please downgrade software to 1.1.2 version. Official firmware: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img - Do it two times to downgrade all stored images. - Apply factory image via web-gui. Serial + TFTP method: - downgrade to 1.1.2 two times - connect ehternet and serial cable - set ip address of tftp server to 192.168.1.254 - put openwrt factory image to tftp folder and rename it to macan.bin - stop device while booting in u-boot - run command: "run flashimg" - run command: "setenv boot_part 1" - run command "saveenv" - reset Back to stock: - Please use old non-gpg image like this 1.1.2: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img - ssh to router and copy image to tmp - use sysupgrade -n -F Tested by github users: @jack338c and @grzesiczek1 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: use switch trigger for WAN LED on NETGEAR boardsDavid Bauer2019-11-041-1/+1
| | | | | | | | | With this commit, the WAN LED is triggered by the switch port state instead of the eth0 netdev. Otherwise, the LED is always illuminated, regardless of the WAN port link state. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: fix LED configuration for NEC Aterm WG2600HPINAGAKI Hiroshi2019-02-281-1/+1
| | | | | | | NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should be used as a portmask instead of "0x1e" for "WAN" LED configuration. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for Buffalo WXR-2533DHPINAGAKI Hiroshi2019-01-012-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
* ipq806x: Add support for IPQ8064 AP161 boardRam Chandra Jangir2018-11-261-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU - RAM: 512MB DDR3 System Memory - NOR Flash: 32MB SPI NOR - NAND Flash: 256MB NAND - Ethernet: 5 x 1G via QCA8337N - USB: 2 x USB 3.0 SuperSpeed - PCIe: 3x Mini PCIe 2.0 Slots Three PCIE2.0 connectors can connect two or three radio cards such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN How to flash via u-boot console: tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin nand erase 0x1340000 0x4000000 nand write 0x44000000 0x1340000 $filesize setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’ saveenv bootm Further upgrades via sysupgrade. Tested on IPQ8064 AP161 Board: 1) NAND boot 2) Tested USB and PCIe interfaces 3) WDOG test 4) cpu frequency scaling 5) ethernet, 2G and 5G WiFi 6) ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ipq806x: fix numbering for Netgear R7800 LAN portsAleksandr V. Piskunov2018-07-041-5/+5
| | | | | | | | | | Netgear R7800 switch LAN ports are numbered backwards in LuCI, i.e. numbering is not corresponding to the actual physical port labels, patch fixes that. Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com> [merged with existing board using the same config] Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: switch the NBG6817 wlan LEDs from amber to whiteStefan Lippers-Hollmann2018-06-281-2/+0
| | | | | | | | | | | | | | | | | The original device support patch configured the amber wlan LEDs (which are meant as error indicator by the OEM) controlled by the SOC's GPIO as wlan traffic indicators, as the correct white wlan LEDs are connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were not accessible. The recent addition of GPIO/ LED support to ath10k now makes it possible to use the correct white LEDs instead - and "mac80211: ath10k: use tpt LED trigger by default" also enables them by default. While both LEDs are independent of each other (two separate LEDs sharing one light tunnel), triggering both on wlan traffic is not the intended behaviour (bright yellow light). Tested on the ZyXEL NBG6817. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-192-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for Compex WPQ864Christian Mehlis2018-03-152-7/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop ipq40xx supportJohn Crispin2018-03-142-17/+0
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: add support for GL.iNet GL-B1300Dongming Han2018-02-142-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for GL.iNet GL-B1300 Specification: - SOC: IPQ4028 / QCA Dakota - RAM: 256 MiB - FLASH: 32 MiB - ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN) - USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) - WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2 - WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2 - INPUT: one reset and one WPS button - LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved - UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1 Installation: Method 1: - use serial port to stop uboot - uboot command: run lf Method 2: - push down reset button and power on - wait until three leds constantly on then release - upgrade by uboot web at http://192.168.1.1 Note: - the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method. - the sysupgrade image can be automatically downloaded if tftp server at 192.168.1.2 have that file. - the wifi led will be flashing when writing image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq806x: mark AVM FB4040 switchport as untaggedDavid Bauer2018-02-111-1/+1
| | | | | | | | This commit marks the CPUs switchport explicit as untagged. Otherwise, an eth0.1 interface is created and the devices LAN-ports are not working. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: add support for OpenMesh A42Sven Eckelmann2018-01-131-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ401x * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet * powered only via POE - 802.3af POE on Ethernet 1 - 18-24v passive POE (mode B) on Ethernet 2 The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq806x: Sort occurrences of boardame alphabeticallyLuis Araneda2018-01-132-29/+28
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: convert to dt-based board-detectionLuis Araneda2018-01-132-38/+38
| | | | | | | | | | | | | | | | | Use the generic board detection method: - Board name: First compatible string from the device tree - Board model: Model property from the device tree Change occurrences of board name in userspace by the compatible string, and removed target specific board detection script Replace the definition of SUPPORTED_DEVICES in Device/Default to extract the dt compatible string from each device definition. Additionally, for devices supported by lede-17.01, append the value of BOARD_NAME to SUPPORTED_DEVICES in the device definition. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: add a helper variable with the vendor name strippedLuis Araneda2018-01-131-0/+1
| | | | | | | | | | This will allow to maintain the current syntax for LEDs config when switching to a device tree compatible string boardname. None of the current boards use a comma in the boardname, so they will be unaffected. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: nbg6817: sync MAC addresses to the upstream valuesStefan Lippers-Hollmann2017-11-031-2/+2
| | | | | | | | | | | | | | | | | | | | | | The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses are stored in the ART partition and the generated MAC addresses for the wlan interfaces alternate randomly between 12:34:56:78:90:12 and 00:03:7f:12:34:56. interface new/ OEM MAC old MAC wlan-2.4g (phy1): ethaddr undefined wlan-5g (phy0): ethaddr + 1 undefined lan : ethaddr + 2 ethaddr wan : ethaddr + 3 ethaddr + 1 This patch defines stable MAC addresses for the wlan interfaces for the first time instead of generating them at random. The previously defined values for lan/ wan are changed to follow the settings of the OEM firmware. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: Archer C2600: fix switch ports numberingBaptiste Jonglez2017-08-241-1/+4
| | | | | | | The order of LAN ports shown in Luci is reversed compared to what is written on the case of the device. Fix the order so that they match. Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* treewide: use the generic board_name functionMathias Kresin2017-07-152-4/+2
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: fix EA8500 switch configurationJo-Philipp Wich2017-05-031-1/+1
| | | | | | | | | Do not assign the CPU port twice, this confuses LuCI and possible other programs relying on topology information in board.json. Ref: https://github.com/openwrt/luci/issues/1086 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: add ipq4019 fritz4040 supportChristian Lamparter2017-03-222-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx/ipq806x/mediatek/mvebu: fix network defaultsJo-Philipp Wich2017-02-071-1/+1
| | | | | | | | | | | After "73d923e base-files: emit tagged switch configuration by default" some default network configurations are broken because the lan and wan ifnames are forcibly set to untagged netdevs. Adjust the offending set_interfaces_lan_wan() calls to use the proper tagged device names. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: more dts cleanupMathias Kresin2016-11-271-19/+5
| | | | | | | | | | | | | | | | | | | | | | | Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this GPIO is mentioned in the GPL tarball, it doesn't do anything. The 2.4/5 GHz LEDs are connected to the wifi chips and not be controlled from the the userspace. Use the LEDs names/colours as they are used in the board manuals. Merge redundant LED configurations. Use the phy[0|1]tpt trigger for the wireless LEDs. Remove the workarounds for the not controllable wireless LEDs. Fix spi compatible strings and remove superfluous spi-max-frequency parameters. If there are two power leds, use one for indicating normal operation and one for failsafe/upgrade. Keep the on/off state of the main power led during boot. Use the usb pinmux settings from the nbg6817 gpl sources. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: clean up dts filesHenryk Heisig2016-11-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the pinmux to the values found in the GPL tarballs of the boards. Remove pinmux which are is not used (like nand pinmux for spi flash boards). This allows to use the wan orange led of the C2600 which had a wrong pinmux before. Might fix buttons or leds of other boards as well. Fix the LED color and the ledswitch key code of the C2600. Rename the ledgnr to ledswitch. Add support for indication the boot state using LEDs to the D7800, NBG6817, R7500 and R7500v2. Change GPIO active to readable values in D7800, EA8500, R7500, R7500v2 and R7800. Change gpioexport to gpio pinmux. Add proper "drive strenght" to i2c4_pins and use it for RPM on C2600, D7800, EA8500, R7500, R7500v2. Remove pcie pinmux from D7800. Move pinctrl to correct place in NBG6817 and R7800. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ipq806x: add support for TP-Link Archer VR2600vSebastian Quilitz2016-11-242-1/+9
| | | | | | | | | | | | | | | | | | This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
* ipq806x: c2600: change wan and lan led trigger to swconfig portHenryk Heisig2016-11-211-2/+2
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ipq806x: fixes for R7800 and C2600Pavel Kubelun2016-11-161-3/+3
| | | | | | | | Updating spi pins configuration in R7800 and C2600 DTs Adding more usb power pin export and gsbi6 in R7800 DT Updating and fixing leds Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix leds, sata port for Netgear R7800 and minor fixes - renamed ↵Pavel Kubelun2016-11-031-2/+9
| | | | | | leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: TP-Link Archer C2600: convert old usbdev trigger to new usbportCezary Jackiewicz2016-11-031-2/+2
| | | | Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ipq806x/nbg6817: add support for ZyXEL NBG6817André Valentin2016-10-262-0/+12
| | | | | | | | | | | | | | | | | CPU: 2x1.8GHz ARM, RAM: 512MiB Storage: 4MiB serial Flash, 3.9GiB MMC NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin to device. Then run: cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4 cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5 reboot -f For debugging serial console is easily visible on board, no soldering needed. Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq806x: C2600: change leds colour nameHenryk Heisig2016-10-151-5/+5
| | | | Signed-off-by: Henryk Heisig hyniu@o2.pl
* ipq806x: Archer C2600: Renaming LED accordance with the standardCezary Jackiewicz2016-08-241-5/+5
| | | | Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
* ipq806x: Build image for Netgear Nighthawk X4 R7500v2Alexis Green2016-08-222-0/+2
| | | | | | Signed-off-by: Alexis Green <alexis@cessp.it> [Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: add initial support for Netgear R7800Pavel Kubelun2016-06-222-8/+10
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: base-files: add support for Linksys EA8500Adrian Panella2016-06-132-0/+13
| | | | Signed-off-by: Adrian Panella <ianchi74@outlook.com>
* ipq806x/base-files: Add Archer C2600 LEDs and boardAsh Benz2016-05-272-0/+8
| | | | Signed-off-by: Ash Benz <ash.benz@bk.ru>
* ipq806x: Add support for Netgear D7800John Crispin2016-01-192-0/+2
| | | | | | Signed-off-by: Tathagata Das <tathagata@alumnux.com> SVN-Revision: 48360
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-112-2/+2
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
* all: remove redundant board.d/00_model filesJo-Philipp Wich2015-12-041-13/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47753
* all: remove dummy ucidef_set_interface_loopback() from board.dJo-Philipp Wich2015-12-031-2/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47744
* kirkwood, ipq806x: fix board.d script permissionsJo-Philipp Wich2015-12-033-0/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47735
* ipq806x: switch from uci-defaults to board.dJo-Philipp Wich2015-12-033-0/+75
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47730
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-20 08:01:02 +0000