| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit fixes and cleanups qcom-ipq8064-wg2600hp.dts to improve the
support for WG2600HP.
- Use dt label in qcom-ipq8064.dtsi:
- gmac1
- gmac2
- gsbi4
- gsbi4_serial
- gsbi5
- hs_phy_0
- ss_phy_0
- usb3_0
- usb3_1
- pcie0
- pcie1
- qcom_pinmux
- Fix wrong pcie reset (perst) gpios
- drop reset-gpio and use perst-gpios in qcom-ipq8064.dtsi
- Remove unnecessary dt label from device dts
- flash
- phy0, phy4
- Rename spi-nor node to "flash" from "m25p80"
- Fix qca,ar8327-initvals
- use oem settings
- fix: PAD0_MODE, PAD6_MODE
- drop: PAD5_MODE (unnecessary)
- Move mtd partitions under partitions (fixed-partitions) node
- Specify "firmware" partition format
- WG2600HP uses uImage format (denx,uimage)
- Change failsafe status LED to power_red
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This follows a similar upstream patch by Rob Herring:
|commit 78e5dfea84dc15d69940831b3981b3014d17222e
|Author: Rob Herring <robh@kernel.org>
|Date: Wed Feb 28 16:44:06 2018 -0600
| powerpc: dts: replace 'linux,stdout-path' with 'stdout-path'
|
| 'linux,stdout-path' has been deprecated for some time in favor of
| 'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
| Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
| |
device_type is deprecated. Upstream doesn't seem to like it either.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
|
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|