aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/kirkwood/base-files
Commit message (Collapse)AuthorAgeFilesLines
* kirkwood: fix HDD LED labels for Zyxel NSA325 in 01_ledsStephan Knauss2020-01-211-2/+2
| | | | | | | | | | Change the LED labels for hdd1/hdd2 in 01_leds to match their counterpart in DTS. Signed-off-by: Stephan Knauss <openwrt@stephans-server.de> [improve commit title and message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit fbf297be38a93b9ca1119e5aaffecd2299087aa5)
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-09-071-2/+2
| | | | | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 8b4bc7abe073489a3595eeb2d81818852319c148) [rmilecki: dropping ARGV without this change broke sysupgrade] Fixes: 6ac62c4b6cae ("base-files: don't set ARGV and ARGC")
* mtd: base-files: Unify dual-firmware devices (Linksys)Jeff Kletsky2019-05-183-34/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
* kirkwood: add support for Iomega Storcenter ix2-200Ademar Arvati Filho2018-07-304-5/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* kirkwood: fix sysupgrade尤晓杰2018-01-181-1/+1
| | | | | | | | | | | | The platform_check_image() stub need to return 0 for success, otherwise the sysupgrade will fail with: Image check 'platform_check_image' failed. Fixes: aa6f5f1787a6 ("kirkwood: use image metadata") Signed-off-by: 尤晓杰 <yxj790222@163.com> [reworded commit message} Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: sort occurrences of boardame alphabeticallyMathias Kresin2018-01-093-29/+28
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: add pogoplug v4Alberto Bursi2018-01-092-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | also known as POGO-V4-A3-02 or POGO-V4-A3-01 SoC: Marvell 88F6192 800Mhz SDRAM memory: 128MB Gigabit ethernet: 1 Marvell 88E1310 Flash memory: 128MB 2 status LEDs (one green one red) 1 "Eject" button on the back (used as "Reset" button) 1 USB 2.0 port (on upper side) 1 sata slot (power + data) for 2.5'' drives (upper side) 2 USB 3.0 ports from a controller on PCIe x1 of the SoC 1 full-size SDcard slot (fits a whole SD card into it) This device supports the (linux-only) kwboot tool to send a new uboot over serial console, so it is easy to unbrick in case the uboot is erased and the device won't boot. ----- Install instructions: ----- Since it's not possible to get ssh access to these devices, the only way to take control is to solder pins to get TTL serial access. Case can be opened by removing screws beneath two rubber feet at back of device, then lifting while prying the sides of the upper part out to unhook a latch on each side about 2/3rds of the way toward the front. Serial connection pins are those labeled "J11", left of SD as you face SD opening. Pins are (from left to right, i.e. the first in the list is the nearest to the SD slot) GND, Rx, Tx. Do not connect +V pin if you use a USB (self-powered) TTL-to-USB dongle. Any USB TTL-to-USB converter will work. Baud rate is 115200, parity "none", databits "8", flow control "none". Stock uboot is unable to read ubi partitions (nor usb) so we will replace it first with our uboot. Start a TFTP server at IP address 169.254.254.254, and place the uboot.kwb file in the folder of the server. Start the serial session and then power up the device. As soon as you see text on the serial start pressing random letter keys to stop the boot process. If you see something like the following line you can proceed: CE>> Otherwise if text is still scrolling by you missed the opportunity, pull the plug and try again. write printenv ethaddr The uboot will write something like this: ethaddr=00:50:43:00:02:02 This is the device's MAC address, also present in the sticker under the device. Write this down as we will need to add it in the new uboot configuration. Use the following commands to load the new uboot: tftp 0x20000 u-boot.kwb If the uboot confirms that the transfer was successful, then you can write it to flash with the following commands: nand erase 0 0x200000 nand write 0x20000 0 0x1c0000 if after the last command the uboot wrote "xxxx bytes written: OK" then it was written correctly and we can proceed. If it did not go well, try again or ask assistence in forums. Shutting down or rebooting at this time will brick the device, to unbrick it you will need to use the kwboot tool from a Linux PC or Virtual Machine. Now write: reset and press enter, the device will reboot and you should see again text scrolling by. Press a random key to stop it, and now you should see pogoplugv4> We now add the MAC address back, write: setenv ethaddr '00:50:43:00:02:02' Confirm that the uboot has understood by writing printenv ethaddr If all looks ok, save the setting with saveenv At this point the uboot is configured, and we only need to load the firmware in the flash memory. Follow the steps below in "Firmware recovery procedure". ---- Firmware recovery procedure ---- The new uboot allows easy recovery from a bad firmware upgrade where you can't access the device anymore over ssh or luci. Take a USB flash drive formatted as FAT32, and copy the initramfs image file in it (it will have "initramfs" in the file name), then rename it as "initramfs.bin". Insert the USB drive in the USB 2.0 port of the pogoplug (the port at the top). Power up the device, and wait for it to finish booting. The uboot should find and load the "initramfs.bin" from usb and if you are connected with serial you should see the linux kernel boot log (text scrolling by). Once it is done, press Enter and you will be greeted by the OpenWRT banner. If you were not connected with serial just wait a bit and, you will be able to access it with ssh or luci web interface (once you find its IP). The recovery "initramfs" images are run from RAM, so you will have to do a normal sysupgrade (firmware upgrade) to write a firmware image to flash memory. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: use the generic board detectMathias Kresin2018-01-098-112/+31
| | | | | | | Drop the target specific detection function in favour of the generic one provided by base-files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: use image metadataMathias Kresin2018-01-091-20/+2
| | | | | | | Append and enforce image metadata. Remove the device specific image checks, they are replaced by image metadata. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: fix compatible string in ib62x0 dtsMathias Kresin2018-01-091-0/+0
| | | | | | | | There is no point in being that specifc in a generic dts covering a range of boards. Keep only the the generic compat string to use it for a devicetree based boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: drop support for orphaned boardsMathias Kresin2018-01-093-30/+1
| | | | | | | No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop support for the boards for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop target board_name functionsMathias Kresin2017-07-151-9/+0
| | | | | | They are not used any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: use the generic board_name functionMathias Kresin2017-07-156-14/+8
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: do board detection during preinitMathias Kresin2017-07-152-1/+9
| | | | | | Do the board detection during preinit to unify it across all targets. Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: automatically handle paths and symlinks for RAMFS_COPY_BINMatthias Schiffer2017-07-111-1/+1
| | | | | | | | | | | | Depending on busybox applet selection, paths of basic utiilties may differ, and may not work as symlinks to busybox. Simply using whatever binary is found in PATH and detecting symlinks automatically is more robust and easier to maintain. The list of binaries is also slightly cleaned up and duplicates are removed. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kirkwood: upgrade: fix RAMFS_COPY_*Matthias Schiffer2017-07-112-21/+4
| | | | | | | | RAMFS_COPY_* are moved to platform.sh toplevel. The nand_do_upgrade call is moved to platform_do_upgrade. Fixes: 30f61a34b4cf "base-files: always use staged sysupgrade" Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kirkwood: switch to kernel 4.9Paul Wassi2017-07-041-2/+2
| | | | | | | | | | | | | | | Add patches-4.9, some of them (heavily) rewritten: - ea4500 is upstream available, keep only LEDE changes in dts - ea3500 is changed to match the structure of the upstream ea4500 dts - nsa310s rewritten to include the common dtsi - nsa325 is dropped, since already upstream Signed-off-by: Paul Wassi <p.wassi@gmx.at> Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> [refresh kernel config, add on100, use the switchdev based mv88e6171 driver for the linksys boards, keep lede specific rootfs/kernel partition names for linksys boards, reorder patches] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: add support for Cisco ON100Makoto Takeuchi2017-06-123-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Cisco ON100 device is a Kirkwood based router: SoC: Marvell 88F6282 1600Mhz SDRAM memory: 512MB DDR3 1333Mhz Gigabit ethernet: 2x Marvell 88E1310 (over RGMII) Flash memory: 512MB 2 bi-colour status LEDs (green/red) 1 Reset button 1 USB 2.0 port (on back) 1 SDIO slot (on back) This commit adds a target profile of "Cisco Systems ON100" under the target system "Marvell Kirkwood". Flashing can be performed over tftp, once "dhcp" has been issued: tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin nand erase 0x0c0000 ${filesize} nand write ${loadaddr} 0x0c0000 ${filesize} Once flashed, set environment variables to boot: setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs \; bootm saveenv Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
* kirkwood: set sata/usb led trigger for NSA3xxAlberto Bursi2017-05-141-0/+6
| | | | | | | | | | | | | these two devices have a Sata led for each sata port. These leds must be controlled separately by a special sata led trigger already used in oxnas target. Both these devices have a single USB led, and to keep consistent behaviour with the Sata leds that show sata activity, this led uses usb-host trigger to show usb activity. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: fix include in etc/board.d/02_networkAlberto Bursi2017-02-281-0/+1
| | | | | | the mtd_get_mac_ascii function called within this script requires the inclusion of /lib/functions/system.sh Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: add ZyXEL NSA325 deviceAlberto Bursi2017-02-113-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add ZyXEL NSA325 2-Bay Media Server The ZyXEL NSA325 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1600Mhz - SDRAM memory: 512MB DDR2 400Mhz - Gigabit ethernet: Marvell Alaska - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II ports (internal) - 2 USB 2.0 ports (back) - 1 USB 3.0 port (front) - Fan (fixed speed) - hardware watchdog in a mcu Basically a bigger, more powerful version of NSA310, installation is the same as they share the same flash layout. A notable difference is that there is a hardware watchdog in a mcu on the board, which is disabled by default in the LEDE u-boot. The watchdog is also disabled with a GPIO activation through raw register change when kwbooting or it would reset the board before the new uboot was transferred. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
* kirkwood: cleanup nsa310b mac address extractionAlberto Bursi2017-02-111-1/+1
| | | | | | | | | switch nsa310b mac address reading to mtd_get_mac_ascii helper as it seems the fw_env.config file is created way later than when network is set up, when I tested I still had that file included in the image through /files folder. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: add ZyXEL NSA310bAlberto Bursi2017-01-245-2/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NSA310 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1200Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: Realtek (over pcie) - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II port (1 internal and 1 external) - 2 USB 2.0 ports (1 front and 1 back) - Smart fan The stock u-boot cannot read ubi so it should be replaced with the LEDE/OpenWRT's u-boot or with a u-boot from here https://github.com/mibodhi/u-boot-kirkwood This device's boot ROM supports "kwboot" tool (in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared) that sends an uboot image to the board over serial connection, it is very easy to unbrick. The stock bootloader can use usb and read from FAT filesystems, so the installation process is simple, place the uboot file on a USB flashdrive formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL to the board and write the following commands in the bootloader console: usb reset fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin nand write 0x1000000 0x00000 0x100000 reset Now you are rebooting in the new u-boot, write this in its console to install the firmware: usb reset fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin nand erase.part ubi nand write 0x2000000 ubi 0x600000 If your firmware file is bigger than 6 MiBs you should write its size in hex instead of 0x600000 above, or remove that number entirely (it will take a while in this case). If you are using another uboot that can read ubi, set mtdparts like this mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi) And set your bootcmd to be like this bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 Then you can install the firmware as described above. After you installed (or configured) the u-boot for booting the firmware, write the device's mac address in the ethaddr u-boot env. The MAC address is usually on a sticker under the device (one of the two codes is the serial), it should begin with "107BEF" as it is assigned to ZyXEL. write in the u-boot console (use your MAC address instead of the example) setenv ethaddr 10:7B:EF:00:00:00 saveenv to save the mac address in the u-boot. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: fix sysupgrade for non-dockstar NAND devicesFelix Fietkau2016-12-301-2/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: fix pogo_e02 LED namePaul Wassi2016-10-261-2/+4
| | | | | | | The pogo_e02's dts file has its LEDs named "pogo_e02:(...)" Fix the status-LED's name for this device. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kirkwood: remove redundant code in etc/board.d/02_networkPaul Wassi2016-10-261-10/+5
| | | | | | | | Remove redundant code: merge boards/cases that share the same network configuration. Also fix the alphabetical ordering of the cases. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* cleanup ucidef_set_interface* usageMathias Kresin2016-09-101-1/+1
| | | | | | | | - quote the interface name - remove call of not existing function - remove the proto if it's the default proto Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood/dockstar: use ubi(kernel, squashfs, ubifs) imagesLuka Perkov2016-03-141-0/+14
| | | | | | | | | | | | | | | | | | | The new image requires `bootz` because of devicetree appending. To flash a new image boot initramfs: tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin bootz 0x800000 # detach if already attached ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}') # scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin # attach is important to resize rootfs_data otherwise it wont boot ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}') Signed-off-by: Alexander Couzens <lynxis@fe80.eu> SVN-Revision: 49010
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-112-2/+2
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
* all: remove redundant board.d/00_model filesJo-Philipp Wich2015-12-041-13/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47753
* kirkwood: add missing board_config_flush(), remove dead codeJo-Philipp Wich2015-12-031-20/+1
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47745
* kirkwood, ipq806x: fix board.d script permissionsJo-Philipp Wich2015-12-033-0/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47735
* kirkwood: switch from uci-defaults to board.dJo-Philipp Wich2015-12-033-20/+33
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47733
* kirkwood: add diag LED on Linksys EA3500Luka Perkov2015-11-101-0/+3
| | | | | | Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47435
* kirkwood: support sysupgrade on Linksys EA[34]500Luka Perkov2015-11-102-0/+111
| | | | | | | | | | This automatically writes to the alternate firmware partition (on Linksys's dual firmware layout) using code borrowed from the WRT1900AC port. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47434
* kirkwood: support Linksys boot counter on EA[34]500Luka Perkov2015-11-101-0/+20
| | | | | | | | | | | | | This is done with existing code from the WRT1900AC port. It makes sure the "auto_recovery" bootloader option is set, and resets the s_env boot counter after a successful boot. This gives users without a serial console connection some measure of safety. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47433
* kirkwood: consistently use engineering board namesLuka Perkov2015-11-104-12/+12
| | | | | | Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47430
* kirkwood: pogo_e02: use mainline led definitionsLuka Perkov2015-11-041-2/+2
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 47385
* kirkwood: add initial support for NSA310sLuka Perkov2015-11-012-0/+5
| | | | | | | Signed-off-by: Tony Dinh <mibodhi@gmail.com> Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 47330
* kirkwood: add support for the Seagate GoflexHomeLuka Perkov2015-05-084-0/+7
| | | | | | | | Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome> Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 45647
* kirkwood: Seagate GoFlex NetLuka Perkov2015-02-124-9/+17
| | | | | | | | | Add GoFlex Net "Board Name" , set and cleanup network default and LEDs. Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 44422
* targets: base-files: diag.sh does not need to be executableLuka Perkov2015-02-071-0/+0
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44305
* kirkwood: drop port-based VLAN setupLuka Perkov2015-01-251-19/+6
| | | | | | | | | | | | | | | | | Using port-based VLANs depends on a non-standard swconfig parameter, which compilcates things like LuCI that don't know about it. This patch changes the default to use 802.1q VLANs internally in the switch, but without tagging packets since we have two Ethernet ports. iperf3 tests indicate no difference in performance versus port-based VLANs when the CPU port is not using tags. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 44122
* kirkwood: enable switch on Linksys EA3500Luka Perkov2015-01-181-0/+3
| | | | | | Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 44036
* target: kirkwood: fix leds defaults configJohn Crispin2015-01-171-11/+11
| | | | | | | | Fix missing parameters in 01_leds Signed-off-by: Gerald Kerma <dreagle@doukki.net> SVN-Revision: 44007
* kirkwood: add *plugs to uci-defaultsLuka Perkov2014-12-192-0/+14
| | | | | | | | | | | | | Set defaults health led to a timer heartbeet (200/800) and populate network for: - GuruplugServerPlus - SheevaPlug - SheevaPlug with eSATA Signed-off-by: Gerald Kerma <dreagle@doukki.net> SVN-Revision: 43752
* kikwood: populate kirkwood.sh with new boardsLuka Perkov2014-12-181-0/+12
| | | | | | | | | | - SheevaPlug - SheevaPlug with eSATA - GuruplugServerPlus Signed-off-by: Gerald Kerma <dreagle@doukki.net> SVN-Revision: 43751
* kirkwood: set default EA4500 switch configLuka Perkov2014-12-181-0/+16
| | | | | | | | | | | This maps the LAN ports to eth0 and WAN port to eth1. Since there are two interfaces the 802.1q VLAN mode is unnecessary and left disabled. Port-based VLANs are used instead. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 43750
* add "preinit_regular" diag.sh set_state argumentJohn Crispin2014-12-151-0/+3
| | | | | | | | | | | | This new argument is used right after starting regular preinit (which happens if failsafe wasn't triggered). The main purpose of "preinit" argument is to indicate that failsafe can be triggered, however we were missing a way to inform user that we don't wait for a trigger anymore. With this change it's clear when failsafe mode can be triggered. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 43715
* kirkwood: add a diag scriptJohn Crispin2014-12-071-0/+29
| | | | | | | | Currently only Linksys EA4500 is supported. Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 43543
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 22:01:49 +0000