aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/kirkwood
Commit message (Collapse)AuthorAgeFilesLines
...
* kirkwood: tidy up image MakefileSungbo Eo2020-02-231-4/+5
| | | | | | | - use k in SIZE variables - break long lines Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: fix device node name of Iomega ix2-200Sungbo Eo2020-02-231-2/+2
| | | | | | | | | | | | | | | The current device node name of ix2-200 is "iom_ix2_200", which results in a SUPPORTED_DEVICES string "iom,ix2,200" that does not match the compatible in DTS and the board name used in board.d. Fix this by replacing the second underscore with a dash, following vendor_model scheme. Fixes: 27b2f0fc0fc5 ("kirkwood: add support for Iomega Storcenter ix2-200") Signed-off-by: Sungbo Eo <mans0n@gorani.run> [commit title/message rephrase] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: do not expose status LED to user config by defaultAdrian Schmutzler2020-02-221-23/+0
| | | | | | | | | | | | So far, the state of status LEDs is set up in 01_leds for many devices in kirkwood target. As those LEDs are also controlled by diag.sh, exposing them to the user via uci config by default seems not helpful and might even have confusing results for the user. Thus, remove the ucidef_set_led_default setup for power/status LED, but do not touch the rest where user control is actually a feature. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: set default state for status LEDs in device treeAdrian Schmutzler2020-02-2226-50/+78
| | | | | | | | | | This adds the default-state = "on"; statement for the power or primary status LED in DTS on kirkwood. This will ensure that this LED will be lit up very early in the boot process (i.e. before diag.sh is executed) and thus will provide an additional hint to the user when problems arise during early boot process. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: add diag LEDs for ZyXEL NSA325Adrian Schmutzler2020-02-222-0/+60
| | | | | | | This device has had no diag LEDs set up so far, so let's just add them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: use generic diag.shPawel Dembicki2020-02-2225-113/+542
| | | | | | | | | | | | | | | | | | This commit removes the target-specific diag.sh script. This way, the generic one is used for the target, which uses DT-aliases to specify the LEDs used. Generic diag.sh allow to use different LEDs to indicate different states. Non-red status LEDs for indicating boot and a running system. Where possible, the red or orange LEDs are used to indicate failsafe mode and a running upgrade. Compile-tested: all target devices. Run-tested: CheckPoint L-50 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [remove unrelated cosmetic changes, rename some labels, add pogo_e02] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: exploit BOARD_NAME to set DEVICE_DTS and SUPPORTED_DEVICESAdrian Schmutzler2020-01-231-20/+2
| | | | | | | | | | | | | | | Due to the history of the target, all devices added before a certain point have the same device string in BOARD_NAME, DEVICE_DTS and added to SUPPORTED_DEVICES. Thus, we can set this one automatically for all devices where BOARD_NAME is specified, removing the explicit DEVICE_DTS and SUPPORTED_DEVICES addition there. For new devices, nothing has changed, and just DEVICE_DTS has to be set manually. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: fix HDD LED labels for Zyxel NSA325 in 01_ledsStephan Knauss2020-01-181-2/+2
| | | | | | | | | Change the LED labels for hdd1/hdd2 in 01_leds to match their counterpart in DTS. Signed-off-by: Stephan Knauss <openwrt@stephans-server.de> [improve commit title and message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kirkwood: Fix FS#505 - Can't install LEDE on Linksys EA3500Eubert Bao2019-10-121-0/+3
| | | | | | | | The default sizes render Device/linksys_audi mage un-flashable. Restore the pagesize, subpagesize, and blocksize for linksys_audi from https://github.com/openwrt/archive. Signed-off-by: Eubert Bao <bunnier@gmail.com>
* treewide: sync bootcount scripts across targetsChuanhong Guo2019-08-171-3/+1
| | | | | | | | | | | | | | | This commit made the following changes to sync all bootcount scripts: 1. use boot() instead of start() This script only needs to be executed once when boot is complete. use boot() to make this explicit. 2. drop sourcing of /lib/functions.sh This is aready done in /etc/rc.common. 3. ramips: replace board name checking with a case Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-2/+2
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kirkwood: split up DEVICE_TITLEMoritz Warning2019-07-101-13/+27
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* kirkwood: image: fix unwanted 2nd inclusion of kernelPetr Štetiar2019-06-091-5/+5
| | | | | | | | | | | | | | | | | | | In commit d2e18dae2892 ("kirkwood: cleanup image build code") the image build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as the KERNEL_IN_UBI needs to be unset in order to make it working as intended, which leads to factory images with two kernels in them: binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin MD5 Checksum: c33e3d1eb0cb632bf0a4dc287592eb70 DECIMAL HEX DESCRIPTION ------------------------------------------------------------------------------- 0 0x0 uImage header [...] "ARM OpenWrt Linux-4.14.123" 5769216 0x580800 uImage header [...] "ARM OpenWrt Linux-4.14.123" Cc: Mathias Kresin <dev@kresin.me> Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285 Fixes: d2e18dae2892 ("kirkwood: cleanup image build code") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mtd: base-files: Unify dual-firmware devices (Linksys)Jeff Kletsky2019-05-183-34/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
* kirkwood: enable sata port multiplierAlberto Bursi2019-05-112-0/+2
| | | | | | | | | | Marvell sata controllers in all kirkwood SoCs support sata port multipliers, just like mvebu. Enable this feature in the default kernel config so it is available in normal builds. tested and working on nsa310b Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* build: add a config option for enabling a testing version of the target kernelFelix Fietkau2019-05-111-0/+1
| | | | | | | If the target supports a newer kernel version that is not used by default yet, it can be enabled with this option Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.14 to 4.14.108Koen Vandeputte2019-03-271-1/+1
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0033-i2c-bcm2835-Add-debug-support.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.24Koen Vandeputte2019-02-221-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kirkwood: add kernel 4.19 supportPaul Wassi2019-02-1715-0/+1525
| | | | | | | | | | | Add patches for 4.19 Drop patch 200-disable-tso, as the packet corruption was fixed in kernel commit 3b89624ab54b9dc2d92fc08ce2670e5f19ad8ec8 Restructure the DTS for Marvell switch in 104-ea3500 and 105-ea4500 to fix DTC warning. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-162-3/+3
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kirkwood: remove linux 4.9 supportFelix Fietkau2018-09-2916-1487/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.9 to 4.9.116Koen Vandeputte2018-08-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches Remove upstreamed patches. - 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch - 403-mtd_fix_cfi_cmdset_0002_status_check.patch - 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch - 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - 900-gen_stats-fix-netlink-stats-padding.patch Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112 - backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch This patch has been slightly altered to compensate for a new helper function introduced in later kernels. Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9 Compile-tested on: ar71xx, bcm2710 Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.59Stijn Tintel2018-07-311-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Drop patch that was superseded upstream: ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch Drop upstreamed patches: - apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch - apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch - ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch - brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch - generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch - generic/pending/900-gen_stats-fix-netlink-stats-padding.patch In 4.14.55, a patch was introduced that breaks ext4 images in some cases. The newly introduced patch backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch addresses this breakage. Fixes the following CVEs: - CVE-2018-10876 - CVE-2018-10877 - CVE-2018-10879 - CVE-2018-10880 - CVE-2018-10881 - CVE-2018-10882 - CVE-2018-10883 Compile-tested: ath79, octeon, x86/64 Runtime-tested: ath79, octeon, x86/64 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kirkwood: add support for Iomega Storcenter ix2-200Ademar Arvati Filho2018-07-307-5/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-221-2/+0
| | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kirkwood: support for buttons in Audi and ViperAlberto Bursi2018-05-151-2/+2
| | | | | | | | | | | | Both these devices have a wps and a reset button on GPIO pins, which need kmod-gpio-button-hotplug package to work. Add this package to their default package config. Troubleshooted and tested on a Viper. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: fix initramfs boot warning on iconnectPaul Wassi2018-03-202-2/+20
| | | | | | | | | | The chosen dts configuration linux,initrd-* gives an error message on bootup of kirkwood-iconnect. Since initramfs/initrd is not used remove these options from the dts. Reported-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kirkwood: switch to kernel 4.14Paul Wassi2018-03-201-1/+1
| | | | Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kirkwood: add kernel 4.14 supportPaul Wassi2018-03-2015-0/+1524
| | | | | | | | | Add patches for 4.14, undoing upstream changes for Linksys devices regarding DSA. Instead, the switchdev driver marvell,88e6171 is used. Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kernel: make mtd patches apply againHauke Mehrtens2018-03-151-5/+5
| | | | | | | | | This makes some of the mtd patches apply again after some generic patches were changed. These problems where found by build bot. Fixes: ac9bcefa3b044 ("kernel: use V10 of mtd patchset adding support for "compatible" string") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.9 to 4.9.77Kevin Darbyshire-Bryant2018-01-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: target/linux/generic/backport-4.9/023-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch target/linux/generic/backport-4.9/023-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch target/linux/generic/backport-4.9/023-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch target/linux/generic/backport-4.9/023-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch CVEs completely or partially addressed: CVE-2017-5715 CVE-2017-5753 CVE-2017-17741 CVE-2017-1000410 Compile-tested: ar71xx Archer C7 v2 Run-tested: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kirkwood: fix sysupgrade尤晓杰2018-01-181-1/+1
| | | | | | | | | | | | The platform_check_image() stub need to return 0 for success, otherwise the sysupgrade will fail with: Image check 'platform_check_image' failed. Fixes: aa6f5f1787a6 ("kirkwood: use image metadata") Signed-off-by: 尤晓杰 <yxj790222@163.com> [reworded commit message} Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: sort occurrences of boardame alphabeticallyMathias Kresin2018-01-094-88/+87
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: add pogoplug v4Alberto Bursi2018-01-094-1/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | also known as POGO-V4-A3-02 or POGO-V4-A3-01 SoC: Marvell 88F6192 800Mhz SDRAM memory: 128MB Gigabit ethernet: 1 Marvell 88E1310 Flash memory: 128MB 2 status LEDs (one green one red) 1 "Eject" button on the back (used as "Reset" button) 1 USB 2.0 port (on upper side) 1 sata slot (power + data) for 2.5'' drives (upper side) 2 USB 3.0 ports from a controller on PCIe x1 of the SoC 1 full-size SDcard slot (fits a whole SD card into it) This device supports the (linux-only) kwboot tool to send a new uboot over serial console, so it is easy to unbrick in case the uboot is erased and the device won't boot. ----- Install instructions: ----- Since it's not possible to get ssh access to these devices, the only way to take control is to solder pins to get TTL serial access. Case can be opened by removing screws beneath two rubber feet at back of device, then lifting while prying the sides of the upper part out to unhook a latch on each side about 2/3rds of the way toward the front. Serial connection pins are those labeled "J11", left of SD as you face SD opening. Pins are (from left to right, i.e. the first in the list is the nearest to the SD slot) GND, Rx, Tx. Do not connect +V pin if you use a USB (self-powered) TTL-to-USB dongle. Any USB TTL-to-USB converter will work. Baud rate is 115200, parity "none", databits "8", flow control "none". Stock uboot is unable to read ubi partitions (nor usb) so we will replace it first with our uboot. Start a TFTP server at IP address 169.254.254.254, and place the uboot.kwb file in the folder of the server. Start the serial session and then power up the device. As soon as you see text on the serial start pressing random letter keys to stop the boot process. If you see something like the following line you can proceed: CE>> Otherwise if text is still scrolling by you missed the opportunity, pull the plug and try again. write printenv ethaddr The uboot will write something like this: ethaddr=00:50:43:00:02:02 This is the device's MAC address, also present in the sticker under the device. Write this down as we will need to add it in the new uboot configuration. Use the following commands to load the new uboot: tftp 0x20000 u-boot.kwb If the uboot confirms that the transfer was successful, then you can write it to flash with the following commands: nand erase 0 0x200000 nand write 0x20000 0 0x1c0000 if after the last command the uboot wrote "xxxx bytes written: OK" then it was written correctly and we can proceed. If it did not go well, try again or ask assistence in forums. Shutting down or rebooting at this time will brick the device, to unbrick it you will need to use the kwboot tool from a Linux PC or Virtual Machine. Now write: reset and press enter, the device will reboot and you should see again text scrolling by. Press a random key to stop it, and now you should see pogoplugv4> We now add the MAC address back, write: setenv ethaddr '00:50:43:00:02:02' Confirm that the uboot has understood by writing printenv ethaddr If all looks ok, save the setting with saveenv At this point the uboot is configured, and we only need to load the firmware in the flash memory. Follow the steps below in "Firmware recovery procedure". ---- Firmware recovery procedure ---- The new uboot allows easy recovery from a bad firmware upgrade where you can't access the device anymore over ssh or luci. Take a USB flash drive formatted as FAT32, and copy the initramfs image file in it (it will have "initramfs" in the file name), then rename it as "initramfs.bin". Insert the USB drive in the USB 2.0 port of the pogoplug (the port at the top). Power up the device, and wait for it to finish booting. The uboot should find and load the "initramfs.bin" from usb and if you are connected with serial you should see the linux kernel boot log (text scrolling by). Once it is done, press Enter and you will be greeted by the OpenWRT banner. If you were not connected with serial just wait a bit and, you will be able to access it with ssh or luci web interface (once you find its IP). The recovery "initramfs" images are run from RAM, so you will have to do a normal sysupgrade (firmware upgrade) to write a firmware image to flash memory. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: sync image filename with boardnameMathias Kresin2018-01-091-34/+42
| | | | | | | | | | Use <manufacturer>_<modelname> as image name. Use the BOARD_NAME variable to ensure that the former used boardname is still used as the subdirectory name for the sysupgrade-tar image, to not break sysupgrade from earlier versions. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: use the generic board detectMathias Kresin2018-01-099-112/+42
| | | | | | | Drop the target specific detection function in favour of the generic one provided by base-files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: use image metadataMathias Kresin2018-01-092-21/+4
| | | | | | | Append and enforce image metadata. Remove the device specific image checks, they are replaced by image metadata. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: fix nsa310b compatible stringsMathias Kresin2018-01-091-1/+1
| | | | | | Use a destinct compatible string fro the nsa310b. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: fix compatible string in ib62x0 dtsMathias Kresin2018-01-092-0/+9
| | | | | | | | There is no point in being that specifc in a generic dts covering a range of boards. Keep only the the generic compat string to use it for a devicetree based boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: drop support for orphaned boardsMathias Kresin2018-01-095-299/+3
| | | | | | | No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop support for the boards for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: cleanup image build codeMathias Kresin2018-01-091-26/+8
| | | | | | | | | | | | | | Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by not supported filesystems or by the legacy image build code. Add common used options/images to the default build code and override the options where necessary. Don't export the kernel image, it isn't required by any board. While at it, change the file extension for the sysupgrade images to bin. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-1/+11
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop target board_name functionsMathias Kresin2017-07-151-9/+0
| | | | | | They are not used any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: use the generic board_name functionMathias Kresin2017-07-156-14/+8
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>