aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq/files-5.4
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: use uniform "u-boot-env" mtd labelMartin Schiller2020-09-1738-38/+38
| | | | | | | | | | | This is the most popular choice in the linux kernel tree. Within OpenWrt, this change will establish consistency with ath79 and ramips targets. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [extend commit message, include netgear_dm200, update base-files] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: remove trailing whitespaces in dtsAleksander Jan Bajkowski2020-09-173-10/+10
| | | | | | Remove trailing whitespaces in dts files. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* lantiq: remove vmmc node from FritzBox 7412 dtsAleksander Jan Bajkowski2020-08-201-4/+0
| | | | | | | | | | | | As described in commit commit 891a7007598d ("lantiq: enable second VPE on Fritz!Box 7412"): The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but rather a proprietary solution based on the DECT chip for the FXS ports. We can remove last traces of vmmc in dts. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* lantiq: fix cosmetic issues with partition offsets and sizesAdrian Schmutzler2020-07-276-8/+8
| | | | | | | This fixes a few cosmetic issues with partition offset and size that are inconsistent probably due to copy/pasting. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq/xrx200: make WLAN button responsive on Fritzbox 7360 & 7362Dustin Gathmann2020-07-201-1/+1
| | | | | | | | | | | | | Pressing the 'WLAN' button should enable/disable wireless activity. Currently, the button is mapped to the KEY_WLAN, which will not have this effect. This patch changes the mapping of the WLAN button, so a button press will emit an action for the 'rfkill' key instead of 'wlan'. Apparently, this is what stock OpenWRT expects. This fix is analogous to the preceding patch for Fritzbox 3370. Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
* lantiq/xrx200: fix WLAN button actions for Fritzbox 3370Dustin Gathmann2020-07-201-1/+1
| | | | | | | | | | | | The WLAN button actions are reversed, i.e. pressing the button emits a 'released' action, and vice versa. This can easily be checked by adding logger -t button_action "$BUTTON $ACTION" as the second line of /etc/rc.button/rfkill, and using logread to read the events (assuming the preceding patch has been applied). Defining the GPIO as ACTIVE_LOW corrects this behavior. Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
* lantiq/xrx200: make WLAN button responsive on Fritzbox 3370Dustin Gathmann2020-07-201-1/+1
| | | | | | | | | | | Pressing the 'WLAN' button should enable/disable wireless activity. However, on the Fritzbox 3370 this doesn't have an effect. This patch changes the mapping of the physical WLAN button, so a button press will emit an action for the 'rfkill' key instead of 'wlan'. Apparently, this is what stock OpenWRT expects, and also what is implemented for most other devices. Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
* lantiq: set correct gphy pins for Zyxel P-2812Willem van den Akker2020-07-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This fixes the gphy LED pins for Zyxel P-2812 devices. The have been accidentally altered during a tidy-up operation (see Fixes: below). No ports were available, dmesg reported: [ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by 1e100bb0.stp; cannot claim for 1e108000.eth [ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22 [ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting, reverse things back [ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22 Fixes: FS#3188 Fixes: 660200e53d62 ("lantiq: dts: assign the GPHY LED pins to the Ethernet controller node") Suggested-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: set port numbers corresponding to reg valueAleksander Jan Bajkowski2020-07-076-53/+53
| | | | | | | | | Fix inconsistencies found in DTS files and sort ethernet ports based on updated names. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> [squash two separate patches, rephrase commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: remove redundant includes from fritz736x DTS filesAleksander Jan Bajkowski2020-07-073-9/+0
| | | | | | | | The removed lines are already included in vr9_avm_fritz736x.dtsi Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> [rephrase commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: dts: Move the &usb_vbus nodes out of &gpioMartin Blumenstingl2020-07-064-48/+48
| | | | | | | | | | | | | | | | | | | | Move the USB VBUS regulator nodes out of the GPIO controller node. This fixes a problem where the "regulator-fixed" driver wasn't probed for these regulators because the GPIO driver doesn't scan the child-nodes and based on the dt-bindings documentation it's not supposed to. This fixed the following error reported by Luca Olivetti: ... dwc2 1e101000.usb: DWC OTG Controller dwc2 1e101000.usb: new USB bus registered, assigned bus number 1 dwc2 1e101000.usb: irq 62, io mem 0x1e101000 dwc2 1e101000.usb: startup error -517 dwc2 1e101000.usb: USB bus 1 deregistered dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517 Fixes: FS#1634 Cc: Luca Olivetti <luca@ventoso.org> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: wifi mac fix for ARV752DPWLars Wessels2020-07-061-1/+4
| | | | | | | | | | | | Set wifi mac from flash partition 'board_config' to match the label on the device (Easybox 802). Currently the wifi mac is always set to 00:0c:43:28:60:00. eth0 and WiFi will now share the same mac (as in original firmware). Signed-off-by: Lars Wessels <software@bytebox.org> [improve commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* lantiq: fritz7312: set maximum speed to 100 mbit on 5.4Adrian Schmutzler2020-06-211-0/+1
| | | | | | | | | | | | The fritz 7312 does not support 1000 gbit. Advertising it makes it worse. Some NIC will change to 1000 gibt and turn off and on again for ever. The previous patch in 36f628910b8b was only applied to the 4.19 file, so let's just make it consistent with this patch. Cc: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: fritz 7360 v2: rename device before it will be usedAlexander Couzens2020-05-181-7/+7
| | | | | | | | | | | Use similiar naming scheme as ath79. Since the fritz 7360 v2 was only in the tree for 2 days, there is no compatibility for the old image. Users which has installed the fritz 7360 v2 before this change, must use sysupgrade --force to skip checks on the board. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq/xrx200: add support for the Fritzbox 7360v2Yushi Nishida2020-05-161-0/+81
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Fritzbox 7360v2 CPU: VR9 500MHz Cores: 2 RAM: 128 MB NOR-Flash: 32 MB WLAN: AR9287-BL1A DECT is not working. Thanks Sebastian Ortwein for adding 7360SL. The dts file is derived from avm_fritz7360sl.dts. Firmware can be flashed with this method: 1.) Set your client IP to 192.168.178.2 2.) Power on your your Fritzbox and connect to 192.168.178.1 via ftp in the first 5 seconds. 3.) login with adam2/adam2 4.) type into the ftp prompt: passive binary debug 1 quote MEDIA FLSH // (not FLASH) put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1 // using the correct location for the squashfs-sysupgrade-firmware.bin 5.) wait till red light flashing turns off. 6.) type: exit Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2. Issue: Ethernet speed is slow, (iperf between a Xiaomi mir3g and this router results in <80Mbits throughput with a wired cable when using the gbit ports.) Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
* lantiq: add Linux 5.4 support as testing kernel versionMathias Kresin2020-03-165-25/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi accordingly. The Lantiq IRQ SMP support added upstream required changes to the SoC dtsi as well. Following changes are made to the Lantiq kernel patches: 0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch 0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch applied upstream 0008-MIPS-lantiq-backport-old-timer-code.patch access_ok API update because it lost it's type (which was the first) parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument from access_ok() function") 0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch 0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch revert upstream changes required for upstream xrx200 ethernet and xrx200 (DSA) switch driver but breaking our driver 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch required for our driver but dropped upstream, add former upstream version 0028-NET-lantiq-various-etop-fixes.patch now has to use the phy_set_max_speed API instead of modifying phydev->supported. Also call ltq_dma_enable_irq() in ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS: lantiq: Do not enable IRQs in dma open") Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: linux 5.4: remove support for the linux,mtd-name OF propertyMartin Blumenstingl2020-03-162-2/+0
| | | | | | | | This is referenced in two .dts but never actually used from userspace. Drop support for this property because it's not used and because it makes updating to Linux 5.4 harder (as the patch doesn't apply anymore). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: copy target to kernel 5.4Mathias Kresin2020-03-1681-0/+12272
Duplicate kernel 4.19 config and patches for kernel 5.4. Duplicate the devicetree source files as well, they need kernel 5.4 specific adjustments. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-30 23:42:45 +0000