| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
| |
Assign the STP pins to the STP GPIO controller node instead of using
pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
| |
Assign the GPHY LED pins to the Ethernet controller node instead of
using pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Assign the NAND pins to the NAND controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
While here, define all NAND pins (CLE, ALE, read/RD, ready busy/RDY and
CE/CS1). This means that the pinctrl subsystem knows that these pins are
in use and cannot be re-assigned as GPIOs for example.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
|
| |
Define the SPI pins in the corresponding SoCs.dtsi and assign them to
the SPI controller node. All known boards use CS4 and it's likely that
this is hardcoded in bootrom so this doesn't bother with having
per-board SPI pinmux settings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Assign the MDIO pins to the switch node instead of using pin hogging
(where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
This converts amazonse, ar9 and vr9. danube is skipped because the pin
controller doesn't define a pinmux for the MDIO pins (some of the SoC
pads may be hardwired to the MDIO pins instead of being configurable).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches.
Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch
Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches.
Altered patches:
- 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
- 0005-mtd-physmap_of-Move-custom-initialization.patch
Remove upstreamed:
- 0001-pinctrl-gemini-Mask-and-set-properly.patch
- 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
|
|
| |
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.
Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In lantiq, ath9k caldata extraction is implemented to work in two
alternate "modes", the standard one and another one with swapped
byte pairs.
This rearranges the functions so "standard" use is based on the
caldata.sh library, while only a single local function is required
for the special case.
Note that while the parameter for switching between normal and swab
is removed, the size of the caldata is added to the function calls
to stay consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
Commit 7519a36774ca ("base-files,procd: add generic service status")
introduced the generic 'status' command which broke the previous
dsl_control status output. To fix this, let's rename the "old" command
to "dslstat".
Fixes: 7519a36774ca ("base-files,procd: add generic service status")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
| |
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
| |
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This makes it possible to configure the link attributes (aneg, duplex,
speed) of each switch ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.
With this patch, the variable is not converted before the check,
but only when it's used in dd.
No conversion is done for use in hexdump, as this can deal with
hex value offsets.
Fixes: b133e466b08e ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
Instead of the nFECS value, the nFEC value (the number of corrected code words)
was mistakenly used.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
|
|
|
|
|
|
|
|
| |
BT Openreach ECI VDSL Modem V-2FUb/I is an alias of Alpha ASL56026 as
also stated in the original commit message adding the device
(commit 6254a2028c "lantiq: add support for the Alpha ASL56026").
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
| |
This sorts the device definitions in image/Makefile alphabetically
for each subtarget/block.
The order of blocks has not been touched.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit unifies the LED mapping of the AVM Fritz!Box routers, which
have a combined Power/DSL LED.
With the stock firmware, the Power LED has the following
characteristics:
- Blink when DSL sync is being established
- Solid when DSL sync is present
We can't completely resemble this behavior in OpenWrt. Currently, the
Power LED is completely off, when DSL sync is missing. This is not
really helpful, as a user might have the impression, that he bricked his
device.
Instead, map the Info-LED to the state of the DSL connection.
There is no consistent behavior for the Info-LED in the stock
firmware, as the user can set it's function by himself. The DSL
connection state is one possible option for the Info LED there.
Also use the red Power LED to indicate a running upgrade, in case the
board has a two-color Power LED.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This adds the led-upgrade alias for the AVM Fritz!Box 7412 to indicate a
running firmware upgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
| |
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.
Therefore, the second VPE can be enabled for use with OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
| |
The AVM FRITZ!Box 7412 buttons are both active low, which is currently
incorrectly defined in the device-tree.
This leads to the device booting directly into failsafe.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches.
Remove upstreamed:
- 023-0013-crypto-crypto4xx-fix-AES-CTR-blocksize-value.patch
- 023-0014-crypto-crypto4xx-fix-blocksize-for-cfb-and-ofb.patch
- 023-0015-crypto-crypto4xx-block-ciphers-should-only-accept-co.patch
- 950-0252-staging-bcm2835_camera-Ensure-all-buffers-are-return.patch
- 950-0253-staging-bcm2835-camera-Remove-check-of-the-number-of.patch
- 950-0254-staging-bcm2835-camera-Handle-empty-EOS-buffers-whil.patch
- 950-0489-staging-mmal-vchiq-Replace-spinlock-protecting-conte.patch
- 0021-ARM-dts-gemini-Fix-up-DNS-313-compatible-string.patch
- 049-v4.20-mips-remove-superfluous-check-for-linux.patch
- 100-MIPS-fix-build-on-non-linux-hosts.patch
- 303-MIPS-Fix-bounds-check-virt_addr_valid.patch
- 0002-usb-dwc2-use-a-longer-AHB-idle-timeout-in-dwc2_core_.patch
Altered patches:
- 950-0267-staging-vc04_services-Split-vchiq-mmal-into-a-module.patch
- 700-net-add-qualcomm-mdio-and-phy.patch
Fixes:
- CVE-2019-3846
New symbol:
- AX88796B_PHY
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
|
|
|
| |
This commit selects wpad-basic for the FRITZ!Box 7312 and 7412 as
wpad-mini is only selected on boards with small flash.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add short description]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
| |
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The following warnings are introduced by our own patches:
lantiq_etop.c:173:1: warning: no semicolon at end of struct or union
};
^
lantiq_etop.c: In function 'ltq_etop_change_mtu':
lantiq_etop.c:725:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
int max = ETH_HLEN + VLAN_HLEN + new_mtu + ETH_FCS_LEN;
^~~
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.
1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[split out treewide patch, integrated P2812HNUF1 rename patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[merged key and led changes, use generic node name for flash, wifi and
gpio]
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
| |
It is pretty ovbious a misuse of the simple-bus binding as no child has
a address.
Luckly the clock node isn't used at all so it is safe to get rid of it.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
| |
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
| |
Set a unit address matching the reg property for the EASY98000 ethernet
node.
Fixes a unit mismatch devicetree compiler warning.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
| |
The localbus childs are highly board specific and need to be part of the
board dts. Otherwise we run into duplicate unit address issues if a
board has something else (NAND) connected to the bus id.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
| |
The register address is the same for danube und vr9. The register size
is 0x400 byte for danube and 0x300 byte for vr9.
The change doesn't have an impact as the vmmc driver doesn't use the
devicetree and has hardcoded register offsets.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
Use only lower case for hex values to keep it consistent.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
| |
Fixes the following devicetree compiler warning:
unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
| |
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
| |
Add size and address cells where missing to fix the following devicetree
compiler warning:
Warning (avoid_default_addr_size): Relying on default #address-cells value
Warning (avoid_default_addr_size): Relying on default #size-cells value
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
SPI nodes only need an address and no size. Drop the size everywhere.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
| |
Fixes:
Warning (unit_address_format): unit name should not have leading "0x"
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The cpu temperature driver has the register offset hardcode and doesn't
need a reg.
The mdio bus node is only used as a well known name and doesn't need a
reg or unit address.
syscon-reboot doesn't have a unit address or a reg either. The unit name
collides with reset-controller@10 anyway.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
| |
Add the reg property if the node has an unit address. Fixes the
following device tree compiler warning:
Warning (unit_address_vs_reg): node has a unit name, but no reg property
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
| |
The memory node is highly board specific and should be only defined in
the board dts.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
| |
The current state of the kernel 4.14 support is in the openwrt-19.07
branch. No need to keep a not default used kernel in this branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
Use kernel 4.19 by default.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
|
|
|
| |
With kernel 4.19 the DMA API relies on a struct device to work properly.
Backport upstream patches which passed a struct device instead of NULL
to the DMA API.
Fixes kernel panics during boot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
|