aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek/image/mt7622.mk
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-181-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 634c13c186646aff2badb51a43b248825d0fe5a0)
* mediatek: mt7622: select bluetooth module instead of firmwareChuanhong Guo2020-09-221-1/+1
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: generate UBI images for the rev boardJohn Crispin2020-07-161-1/+19
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: fix image/mt7622.mkJohn Crispin2020-06-071-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: add bpi-r64 emmc supportJohn Crispin2020-06-071-1/+13
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: tidy up image subtarget MakefilesSungbo Eo2020-06-071-15/+13
| | | | | | | | | | - sort device recipes alphabetically - adjust board name of ELECOM WRC-2533GENT - harmonize line wrapping Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebased] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mediatek: select kmod-mt7615-firmware where kmod-mt7615e is selectedFelix Fietkau2020-06-041-1/+2
| | | | | | | The new mt76 version splits out the firmware, because the driver can also be used for MT7663/MT7613 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: fix image buildingJohn Crispin2020-05-041-0/+2
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: fix elecom board nameJohn Crispin2020-04-061-1/+1
| | | | | | menuconfig was showing the the company name twice. Signed-off-by: John Crispin <john@phrozen.org>
* mediatke: add support for elecom-wrc-2533gentJohn Crispin2020-03-271-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MT7622-based Elecom WRC-2533gent router, with spi-nand storage and 512MB RAM. The device has the following specifications: * MT7622 (arm64 dual-core) * 512MB RAM (DDR3) * 4GB storage (spi-nand) * 5x 1Gbps Ethernet (RTL8337C switch) * 1x UART header * 1x USB 3.0 port * 5x LEDs * 1x reset button * 1x WPS button * 1x slider switch * 1x DC jack for main power (12V) The following has been tested and is working: * Ethernet switch * 2.4g and 5g wifi * USB 3.0 port * sysupgrade * buttons/leds Not working: * bluetooth firmware does not load even though it is present int he rootfs Signed-off-by: John Crispin <john@phrozen.org>
* kernel: make kmod-ata-core selected by dependent modulesupstreamless-old-masterSungbo Eo2020-03-111-4/+2
| | | | | | | | | | | | | | | | Currently kmod-ata-* will not get into images unless kmod-ata-core is added to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to "select", we do not have the issue anymore. Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES and similar variables, as it is now pulled by dependent modules such as: - kmod-ata-ahci - kmod-ata-ahci-mtk - kmod-ata-sunxi While at it, use AddDepends/ata for kmod-ata-pdc202xx-old. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* mediatek: add latest fixes provided by MTKJohn Crispin2020-02-251-14/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: use consistent naming scheme for device nodesAdrian Schmutzler2020-01-261-6/+8
| | | | | | | | | | | | | | | | | | | | | This harmonizes the device node names (and thus the image names, too) between subtargets of the mediatek target. So far, each subtarget has somewhat used its own naming scheme. Now, we use the vendor_device syntax there, too. Since DTS names have different patterns and the target only contains a few devices, this does not replace DEVICE_DTS by a calculated default value (like for other targets). SUPPORTED_DEVICES is adjusted based on the node rename where necessary, though it looks like for several older devices it was not set up correctly so far. While at it, this also changes the DTS name for u7623-02-emmc-512m to all-lower-case. Cc: John Crispin <john@phrozen.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: split up DEVICE_TITLEMoritz Warning2019-10-191-3/+6
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-061-3/+3
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: fix typo in Banana Pi R64 device titleAdrian Schmutzler2019-08-041-1/+1
| | | | | | | The DEVICE_TITLE introduced in 66458c49aa14 ("mediatek: add v4.19 support") is mistyped. Fix it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: add v4.19 supportJohn Crispin2019-08-021-3/+20
| | | | | | | | Bump the target to v4.19. Add a patch with additional eth driver fixes/features that MTK provided aswell as the driver for the new mt7530 switch. Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: add mt7622 subtargetJohn Crispin2018-05-241-0/+9
Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2025-09-28 09:23:27 +0000