aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/mtk_eth_soc.c
Commit message (Collapse)AuthorAgeFilesLines
* ramips: ethernet: Replace random_ether_addr with eth_hw_addr_randomRosen Penev2019-10-271-1/+1
| | | | | | eth_hw_addr_random additionally sets addr_assign_type to NET_ADDR_RANDOM. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for Edimax EW-7476RPC / EW-7478ACBirger Koblitz2019-06-201-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: 192.168.9.2/24). http://192.168.9.2/index.asp ramips: add Edimax EW-7478AC SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: http://edimaxext.setup) Or push wpa button on power on and send firmware via tftp to 192.168.1.6 The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal antennas it has 2 external ones. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [merge conflict in 01_leds] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: ethernet: remove unused SIOCETHTOOL ioctl handlingPetr Štetiar2019-06-051-12/+1
| | | | | | | | | | | | | This ioctl is currently routed through generic interface code. dev_ioctl dev_ethtool __ethtool_get_link_ksettings phy_ethtool_ioctl Cc: Felix Fietkau <nbd@nbd.name> Cc: John Crispin <john@phrozen.org> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: implement vlan rx offload on MT7621Felix Fietkau2019-04-031-1/+8
| | | | | | Avoids the overhead of software VLAN untagging in the network stack Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: ethernet: unify tx descriptor buffer splittingFelix Fietkau2018-09-031-75/+83
| | | | | | | | A buffer is split into multiple descriptors if it exceeds 16 KB. Apply the same split for the skb head as well (to deal with corner cases on fraglist support) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: ethernet: use own page_frag_cacheFelix Fietkau2018-07-121-3/+14
| | | | | | | | | | | | | | | | Using the NAPI or netdev frag cache along with other drivers can lead to 32 KiB pages being held for a long time, despite only being used for very few page fragment. This can happen if the ethernet driver grabs one or two fragments for rx ring refill, while other drivers use (and free up) the remaining fragments. The 32 KiB higher-order page can only be freed once all users have freed their fragments, which only happens after the rings of all drivers holding the fragments have wrapped around. Depending on the traffic patterns, this can waste a lot of memory and look a lot like a memory leak Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: ethernet: use skb_free_frag to free fragmentsFelix Fietkau2018-07-121-3/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: improve ethernet driver performance with GRO/TSOFelix Fietkau2018-06-191-66/+101
| | | | | | | | | | | GRO stores packets as fraglist. If they are routed back to the ethernet device, they need to be re-segmented if the driver does not support sending fraglists. Add the missing support for that, along with a missing feature flag that allows full routed GRO->TSO offload. Considerably reduces CPU utilization for routing Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621: fix mtu setting with kernel 4.14Mathias Kresin2018-06-161-11/+7
| | | | | | | | | | Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It's necessary to set a max_mtu if a mtu > 1500 is supported. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: rename ethernet driver folder to the same one that upstream usesFelix Fietkau2018-06-131-0/+1648
Preparation for sharing offload code with the mediatek target through generic files/ Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-26 14:08:38 +0000