aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt7620.mk
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix Planex CS-QR10 device packagesMathias Kresin2017-11-221-1/+3
| | | | | | | | | Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will not be autoselected. Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix DCH-M225 supportMathias Kresin2017-11-221-1/+1
| | | | | | | | | | | | | | Setting the pins of the uartf group to gpio+i2s at the time the i2c driver loads is to late for the WPS gpio button. The gpio-keys driver fails to load since the pin used by the WPS button is not yet set to GPIO. The WPS button with the rfkill keycode is essential for this wifi only board. Add the missing sound and i2c kernel modules corresponding to the device nodes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Youku-YK1 supportEdmunt Pienkowsky2017-10-271-1/+2
| | | | | | | | | | | | | | | | | | | | | | Remove the ephy-pins from the ethernet device tree node. The ephy-pins are useed to controll the ePHY LEDs and this board doesn't have these. Instead one of the ePHY pins is used in GPIO mode to control the WAN LED. Use the switch LED trigger to control the WAN LED. Move the power LED handling to diag.sh to show the boot status via this LED. Add the missing kernel packages for USB and microSD card reader to the default package selection. Fix the maximum image size value. The board has a 32MByte flash chip. Fixes: FS#1055 Signed-off-by: Edmunt Pienkowsky <roed@onet.eu> [make the commit message more verbose, remove GPIO pinmux for pins not used as GPIOs] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix default usb support for nexx wt3020-8MAlberto Bursi2017-10-241-0/+1
| | | | | | | the nexx wt3020-8M has a usb 2.0 port, add usb 2.0 support packages to its default package list. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* ramips: mt7620: do not pad sysupgrade Archer imagesThibaut VARENE2017-10-041-3/+3
| | | | | | | | | | | | | | | | The current makefile unnecessarily pads sysupgrade image for Archer devices. This has three implications: 1. higher risk of OOM when uploading the binary image to the device 2. much slower upgrade due to time wasted erasing and writing padding 3. grows image beyond available flash size if metadata are appended This is already fixed in master, albeit in a completely different way (the whole target have been reworked) Fixes: FS#1025, FS#1039 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: add factory firmware for Tp-Link C20i/C50Henryk Heisig2017-05-051-0/+4
| | | | | | TP-Link firmware doesn't accept sysupgrade.bin with metadata. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for Sanlinking D240Kristian Evensen2017-04-281-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sanlinking Technologies D240 (http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same device as the ZBT WE826, so adding support for it in LEDE is straight forward. The differences is that the D240 has two mini-PCIe slots (instead of one), blue LEDs and supports PoE. Specification: * CPU: MT7620A * 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps. * 16 MB Flash. * 128 MB RAM. * 1x USB 2.0 port. * 2x mini-PCIe slots. * 2x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to test the SD card reader. The device comes pre-installed with an older version of OpenWRT, including Luci. In order to install LEDE, you need to follow the existing procedure for updating OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. The default router address is 192.168.10.1 and username/password admin/root (at least on my devices). If you brick the device, the procedure for recovery is the same as for the WE826. Please see the wiki page for that device for instructions. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: ZyXEL Keenetic Viva: align factory imagesVitaly Chekryzhev2017-04-281-1/+1
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Omni align factory imagesVitaly Chekryzhev2017-04-281-2/+2
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add support for Netgear WN3000RPv3Thibaut VARENE2017-04-281-0/+11
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3000RPv3 http://www.netgear.com/support/product/wn3000rpv3.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Serial: JP1 header, 57600-8N1 - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This is why the same fakeroot image is used for the WN3000 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* build: use mkhash to replace various quirky md5sum/openssl callsFelix Fietkau2017-01-051-4/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: use new image build code for more devicesMathias Kresin2016-12-241-7/+0
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use different board names for variantsMathias Kresin2016-12-241-2/+0
| | | | | | | | | | | | Use different names for flash size related board variants, to make sure that only images for the actual flash size are considered as valid by the image validation code. Remove the flash size suffix from the string returned by ramips_board_detect() to ensure that existing scripts relying on the former used boardname are still working. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix image validation errorsMathias Kresin2016-12-241-0/+2
| | | | | | | | | | | The name from the Device define will be used in the metadata. Due to typos/different spelling, this name might not match the one exported in /lib/ramips.sh. Fix all name mismatches which were found by checking if the name used in the metadata exists in /lib/ramips.sh. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix tplink image building fix sysupgrade firmware on MR200Henryk Heisig2016-12-241-4/+5
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: Add support to TP-Link Archer MR200Henryk Heisig2016-12-221-0/+10
| | | | | | | | | | CPU: MT7620N 580MHz Flash: 8MB RAM: 64MB build-in modem 3G/4G four ethernet port 10/100Mbps Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for ZyXEL Keenetic Omni / Omni IIVitaly Chekryzhev2016-12-221-0/+20
| | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add size checks/append metadata where missingMathias Kresin2016-11-271-6/+12
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: append metadata to imagesFelix Fietkau2016-11-191-8/+10
| | | | | | | metadata checks are not enforced yet, because some images are still being built by legacy code Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for ZyXEL Keenetic VivaVitaly Chekryzhev2016-11-181-0/+14
| | | | | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [removed linux,modalias parameter from flash node in dts] [removed sdhci node from dts; no sd card slot here] Signed-off-by: Mathias Kresin <dev@kresin.me>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-3/+3
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: Add support for Phicomm K2 PSG1218Xuefu Lin2016-10-041-0/+7
| | | | | | | | | - CPU: MT7620A 580MHz - Flash: 8MB - RAM: 64MB - External PA+LNA on both WLAN2.4 and WLAN5 - 4x LAN ethernet and 1x WAN ethernet Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips: Add support for ZBT-CPE102Cezary Jackiewicz2016-09-271-0/+7
| | | | | | | | | | - CPU: MT7620N 580MHz - Flash: 8MB - RAM: 64MB - build-in minipcie slot for modem 3G/4G - one ethernet port 10/100Mbps Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: move seama build recipe to MakefileMathias Kresin2016-09-031-9/+0
| | | | | | | The identical build step is defined twice. Move it to the parent Makefile to use only one version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: set blocksize for 4MB devicesMathias Kresin2016-09-031-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | Set the blocksize for devices having only 4MB of flash for ramips devices already using the new image build code. Informations about the used flash chip are gathered from the OpenWrt wiki, wikidevi, forums, OEM bootlogs or the compatible property in the device tree source file. The en25q32b from the AirLive Air3GII does not have 4k support in the kernel. For the following boards no information about the used flash chip could be found and a 64k blocksize is assumed: - Ralink V11ST-FE - Ralink AP-RT3052-V22RW-2X2 - MediaTek MT7628 EVB - MediaTek MT7621 EVB - UPVEL UR-326N4G - Buffalo WZR-AGL300NH Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: don't set the same max image size twiceMathias Kresin2016-09-041-20/+0
| | | | | | The ralink_default_fw_size_8M is already set for the default device. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: specify max image size in Kilobyte/MegabyteMathias Kresin2016-09-041-17/+9
| | | | | | Use the k and m unit suffix to be consistent with the blocksize. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: move umedia build step to MakefileMathias Kresin2016-08-201-4/+0
| | | | | | Some rt3883 based boards need this one as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support for D-Link DCH-M225Michael Lee2016-07-111-0/+28
| | | | | | | | D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash, 3.5mm audio out support. but no ethernet and usb ports. so you must default enable wifi. Signed-off-by: Michael Lee <igvtee@gmail.com>
* ramips: add suport for ZBT APE522IIRoger Pueyo Centelles2016-06-221-0/+8
| | | | | | | | | The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has 64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with 802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac MT7612E-based 5 GHz radio. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips/image: Add Archer C50 to mt7620 MakefileHenryk Heisig2016-06-131-0/+9
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: fix Netgear EX2700 imagesJoseph C. Lehner2016-06-051-3/+3
| | | | | | | Calling `cat foo bar | dd ... conv=sync` *may* add extraneous padding. Avoid this. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: fix Netgear EX2700 imagesJoseph C. Lehner2016-05-301-2/+3
| | | | | | | | The previous image creation code would have failed if the unpadded kernel uImage size was less than 64 bytes from the next erase block boundary. Fix that. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: fix Netgear EX2700 imagesJoseph C. Lehner2016-05-271-8/+4
| | | | | | | | The bootloader on this device expects the kernel partition to end on a 64k boundary. The last 64 byte of the kernel partition must contain a valid uImage header (the fakeroot partition). Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: fix 8M WT3020 image creationJohn Crispin2016-05-161-1/+1
| | | | | | fix image size for 8M version : 4M -> 8M Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
* ramips: fix ArcherC20i image creation - 3rd tryJohn Crispin2016-05-151-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: fix Archer C20i image buildFelix Fietkau2016-05-151-2/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix ArcherC20i image creationJohn Crispin2016-05-141-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: fix indentation of Build/* template commandsFelix Fietkau2016-05-121-7/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: convert mt7620 to new image building codeJohn Crispin2016-05-121-160/+381
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add support for Planex MZK-EX750NP.blogic2016-05-101-0/+2
| | | | | | | | | | | add support for Planex MZK-EX750NP. MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater. Built-in power supply. 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49268
* ramips: add support for Planex MZK-EX300NPJohn Crispin2016-04-261-0/+2
| | | | | | | | | | MZK-EX300NP is MT7620A based wifi repeater. Built-in power supply. 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49235
* ramips: add support for Planex CS-QR10John Crispin2016-04-261-0/+2
| | | | | | | | | | | | CS-QR10 is MT7620A based IP Camera. the camera and sound does not work with kernel 4.4. - camera chip is sn9c291. - sound chip is wm8960. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49234
* ramips: add support for ELECOM WRH-300CRJohn Crispin2016-04-211-0/+15
| | | | | | | | | | | | | | ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but easy-to-access) UART. it also has internal USB hub and USB card reader which provide one USB port, one SD card slot, and one microSD card slot. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> SVN-Revision: 49211
* ramips: move different subtarget image generation to separate makefiles to ↵John Crispin2016-04-011-0/+160
improve maintainability - all subtarget specific defines are in their own files - common defines left in main Makefile - each subtarget makefile idefed with SUBTARGET - all subtargets compile tested - few seems to be broken/unneeded things marked with FIXME Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49104
generated by cgit v1.2.3 (git 2.25.1) at 2025-09-28 23:52:48 +0000