aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt76x8
Commit message (Collapse)AuthorAgeFilesLines
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-062-2/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: 5.10: refresh configsIlya Lipnitskiy2021-03-061-4/+4
| | | | | | | | Run-tested on Ubiquiti EdgeRouter X. Compile tested on all other subtargets. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: copy config-5.4 to config-5.10Ilya Lipnitskiy2021-03-061-0/+191
| | | | | | Strict copy, no changes made. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* Revert "ramips: add support for kernel 5.10"Adrian Schmutzler2021-03-061-191/+0
| | | | | | | | | This reverts commit b4aad29a1d7ad77d67073c1c54b28c429c64ed9b. This was accidentally folded into a single commit. Remove it and apply it properly again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for kernel 5.10Ilya Lipnitskiy2021-03-051-0/+191
| | | | | | | | | | | | | | | | | | | | | | | | | Enable testing kernel. Delete upstreamed patches: 0098-disable_cm.patch can be dropped, upstream fixed CM handling. Fix compile errors by using new kernel APIs. Fix fuzz by manually editing patches to ensure the code goes in the right place. For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit a307593a6 to keep the OpenWrt ralink driver operational. Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693 and #3952. Rename patches to follow the 3-digit classification from the OpenWrt Developer Guide. Run automatic quilt refresh. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: 5.4: refresh configsIlya Lipnitskiy2021-03-051-54/+3
| | | | | | Automatic refresh by running make kernel_oldconfig on each target. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: add support for ELECOM WRC-1167FSINAGAKI Hiroshi2021-02-112-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for Hi-Link HLK-7688AEwan Parker2021-02-052-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7688AN - RAM: 128 MB - Flash: 32 MB - Ethernet: 5x 10/100 (1x WAN, 4x LAN) - Wireless: built in 2.4GHz (bgn) - USB: 1x USB 2.0 port - Buttons: 1x Reset - LEDs: 1x (WiFi) Flash instructions: - Configure TFTP server with IP address 10.10.10.3 - Name the firmware file as firmware.bin - Connect any Ethernet port to the TFTP server's LAN - Choose option 2 in U-Boot - Alternatively choose option 7 to upload firmware to the built-in web server MAC addresses as verified by OEM firmware: use address source 2g *:XX factory 0x4 LAN *:XX+1 factory 0x28 WAN *:XX+1 factory 0x2e Notes: This board is ostensibly a module containing the MediaTek MT7688AN SoC, 128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in IoT Gateway Mode or IoT Device Mode. From some vendors the U-Boot that comes installed operates on UART 2 which is inaccessible in gateway mode and operates unreliably in the Linux kernel when using more than 64 MB of RAM. For those, updating U-Boot is recommended. Signed-off-by: Ewan Parker <ewan@ewan.cc> [add WLAN to 01_leds] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove generic profilesAdrian Schmutzler2021-01-271-17/+0
| | | | | | | | | | | | | On a platform with many very different devices, like found on ramips, the generic profiles seem like remnants of the past that do not have a real use anymore. Remove them to have one thing less to maintain. Actually, rt288x didn't have a default profile in the first place. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* ramips: use full names for Xiaomi Mi Router devicesAdrian Schmutzler2020-12-081-3/+3
| | | | | | | | | | This aligns the device/image names of the older Xiaomi Mi Router devices with their "friendly" model and DEVICE_MODEL properties. This also reintroduces consistency with the newer devices already following that scheme. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Xiaomi Mi Router 4CAtaberk Özen2020-11-252-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi's Mi Router 4C device. Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LEDs: 2x yellow/blue. Programmable (labelled as power on case) - Non-programmable (shows WAN activity) - Button: Reset How to install: 1- Use OpenWRTInvasion to gain telnet and ftp access. 2- Push openwrt firmware to /tmp/ using ftp. 3- Connect to router using telnet. (IP: 192.168.31.1 - Username: root - No password) 4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into the router.. 5- It takes around 2 minutes. After that router will restart itself to OpenWrt. Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com> [wrap commit message, bump PKG_RELEASE for uboot-envtools, remove dts-v1 from DTS, fix LED labels] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link MR6400 v5Filip Moc2020-11-252-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are: - smaller form factor - different LED GPIOs - different switch connections You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v5.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>
* ramips: add support for TP-Link MR6400 v4Filip Moc2020-11-232-0/+8
| | | | | | | | | | | | | | | | | | | | | | | You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v4.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>
* ramips: add support for the Hak5 WiFi Pineapple Mark 7Marc Egerton2020-11-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WiFi Pineapple Mark 7, a wireless penetration testing tool. Specifications: * SoC: MediaTek MT7628 (580MHz) * RAM: 256MiB (DDR2) * Storage 1: 32MiB NOR (SPI) * Storage 2: 2GB eMMC * Wireless 1: 802.11b/g/n 2.4GHz (Built In) * Wireless 2: 802.11b/g/n 2.4GHz (MT7601) * Wireless 3: 802.11b/g/n 2.4GHz (MT7601) * USB: 1x USB Type-A 2.0 Host Port * Ethernet: 1x USB Type-C AX88772C Ethernet * UART: 57600 8N1 on PCB * Inputs: 1x Reset Button * Outputs: 1x RGB LED * FCCID: 2AA52MK7 Flash Instructions: Original firmware is based on OpenWRT. Use sysupgrade via SSH to flash. Signed-off-by: Marc Egerton <foxtrot@realloc.me> [pepe2k@gmail.com: set only required/used gpio groups to gpio function] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for TP-Link RE200 v4Richard Fröhning2020-10-202-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2/v3. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - 8x LED (GPIO-controlled), 2x button - UART connection holes on PCB (57600 8n1) There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:8E 2.4G: *:8D 5G : *:8C MAC address assignment has been done according to the RE200 v2. The label MAC address matches the OpenWrt ethernet address. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Recovery -------- Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Instructions for serial console and recovery may be checked out in commit 6d6f36ae787c ("ramips: add support for TP-Link RE200 v2") or on the device's Wiki page. Signed-off-by: Richard Fröhning <misanthropos@gmx.de> [removed empty line, fix commit message formatting] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: remove set_wifi_led function in 01_ledsAdrian Schmutzler2020-10-021-12/+8
| | | | | | | | | | | | | | | | | | | While we mostly use the ucidef_set_led_* functions directly in 01_leds we still have the set_wifi_led function in parallel for several old devices. This is not only inconsistent with the other definitions, it also links to the wlan0 interface instead of using a phy trigger which would be independent of the interface name (and is used for all newer devices anyway). Apart from that, the standard names "wifi" and "wifi-led" are not very helpful in a world with different radio bands either. Thus, this patch removes the set_wifi_led function and puts the relevant commands into the cases explicitly. This makes the mechanism used more evident and will hopefully lead to some future improvements or at least prevent some copy-pasting of the old setups. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove option to set WiFi LED via aliasesAdrian Schmutzler2020-10-021-4/+5
| | | | | | | | | | | | | In ramips, it's not common to use an alias for specifying the WiFi LED; actually only one device uses this mechanism (TL-WR841N v14). Particularly since the WiFi LEDs are typically distinguished between 2.4G and 5G etc. it is also not very useful for this target. Thus, this patch removes the setup lines for this mechanism and converts the TL-WR841N v14 to the normal setup. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove model name from LED labelsAdrian Schmutzler2020-10-022-88/+59
| | | | | | | | | | | | | | | | | Like in the previous patch for ath79 target, this will remove the "devicename" from LED labels in ramips as well. The devicename is removed in DTS files and 01_leds, consolidation of definitions into DTSI files is done where (easily) possible, and migration scripts are updated. For the latter, all existing definitions were actually just devicename migrations anyway. Therefore, those are removed and a common migration file is created in target base-files. This is actually another example of how the devicename removal makes things easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link TL-WR850N v2Andrew Freeman2020-08-272-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR850N v2. This device is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13. Specifications: SOC: MediaTek MT7628NN Flash: 8 MiB SPI RAM: 64 MiB WLAN: MediaTek MT7628NN Ethernet: 5 ports (100M) Installation Using the integrated tftp capability of the router: 1. Turn off the router. 2. Connect pc to one of the router LAN ports. 3. Set your PC IPv4 address to 192.168.0.66/24. 4. Run any TFTP server on the PC. 5. Put the recovery firmware on the root directory of TFTP server and name the file tp_recovery.bin 6. Start the router by pressing power button while holding the WPS/Reset button (or both WPS/Reset and WIFI buttons) 7. Router connects to your PC with IPv4 address 192.168.0.2, downloads the firmware, installs it and reboots. LEDs are flashing. Now you have OpenWrt installed. 8. Change your IPv4 PC address to something in 192.168.1.0/24 network or use DHCP to get an address from your OpenWrt router. 9. Done! You can login to your router via ssh. Forum link: https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899 Signed-off-by: Andrew Freeman <labz56@gmail.com> [squash an tidy up commits, sort nodes] Signed-off-by: Darsh Patel <darshkpatel@gmail.com> [minor commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-1/+1
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: tidy up MAC address setup for Linkit Smart and Omega2Adrian Schmutzler2020-08-061-6/+0
| | | | | | | | | | | | | | | | | | | | Linkit Smart 7688 and Onion Omega 2(+) are one-port devices, and have their port set to LAN by default. Setting up a WAN MAC address for them doesn't make any sense, as no wan interface will be created in uci config. Despite, these devices also set lan_mac in 02_network, although mtd-mac-address sets a different address for the ethernet interface in DTS. Clean this up by moving the lan_mac value into DTS and dropping the entries in 02_network completely. That way, the effective address on the LAN interface should stay the same, but we get rid of the extra (re)assignments. As I don't have access to the devices, this does not tell anything about whether 0x2e is actually a good choice, it just preserves the existing assignment. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: WizFi630S use macs from factory partionTobias Welz2020-08-061-2/+5
| | | | | | | | | | | | | | | | | | | | WIZnet WizFi630s has three mac addresses in the factory partition: 0x04 (also on the label), 0x28 for wan mac and 0x2e as lan mac. All three macadresses are sequential series of addresses. This is making use of them. While at it, also add the label MAC address to 02_network. MAC addresses as verified by OEM firmware: use interface source WLAN ra0 factory 0x04 (label) WAN eth0.2 factory 0x28 (label + 1) LAN eth0.1 factory 0x2e (label + 2) Signed-off-by: Tobias Welz <tw@wiznet.eu> [fix sorting in 02_network, commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-061-1/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: switch rt305x subtarget to kernel 5.4Alexey Dobrovolsky2020-08-051-1/+0
| | | | | | | | | | | | | | RT3x5x seems to work fine with kernel 5.4. Set the default kernel version to 5.4 to bring this to a broader audience. Since 4 of 6 targets are on kernel 5.4 now, invert the kernel version setup logic in Makefile/target.mk files. Tested on ZyXEL Keenetic. Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> [invert version setup logic] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE200 v3Richard Fröhning2020-08-032-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - 8x LED (GPIO-controlled), 2x button Unverified: - UART header on PCB (57600 8n1) There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- MAC address assignment has been done according to the RE200 v2. The label MAC address matches the OpenWrt ethernet address. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Recovery -------- Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. The device has not been opened for adding support. However, it is expected that the behavior is similar to the RE200 v2. Instructions for serial console and recovery may be checked out in commit 6d6f36ae787c ("ramips: add support for TP-Link RE200 v2") or on the device's Wiki page. Signed-off-by: Richard Fröhning <misanthropos@gmx.de> [adjust commit title/message, sort support list] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JS76x8 series DEV boardsRobinson Wu2020-07-311-4/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Jotale JS76x8 series development boards. These devices have the following specifications: - SOC: MT7628AN/NN, MT7688AN, MT7628DAN - RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2) - RAM of MT7628DAN: 64 MB (DDR2) - FLASH:8/16/32 MB (SPI NOR) - Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch) - WIFI:1x 2T2R 2.4 GHz Wi-Fi - LEDs:1x system status green LED, 1x wifi green LED, 3x ethernet green LED - Buttons:1x reset button - 1x microSD slot - 4x USB 2.0 port - 1x mini-usb debug UART - 1x DC jack for main power (DC 5V) - 1x TTL/RS232 UART - 1x TTL/RS485 UART - 13x GPIO header - 1x audio codec(wm8960) Installation via OpenWrt: The original firmware is OpenWrt, so both LuCI and sysupgrade can be used. Installation via U-boot web: 1. Power on board with reset button pressed, release it after wifi led start blinking. 2. Setup static IP 192.168.1.123/4 on your PC. 3. Go to 192.168.1.8 in browser and upload "sysupgrade" image. Installation via U-boot tftp: 1. Connect to serial console at the mini usb, which has been connected to UART0 on board (115200 8N1) 2. Setup static IP 192.168.1.123/4 on your PC. 3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123). 3. Connect one of LAN ports on board to your PC. 4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC. 5. Apply power to board. 6. Interrupt U-boot with keypress of "2". 7. At u-boot prompts: Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y Input device IP (192.168.1.8) ==:192.168.1.8 Input server IP (192.168.1.123) ==:192.168.1.123 Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin 8. board will download file from tftp server, write it to flash and reboot. Signed-off-by: Robinson Wu <wurobinson@qq.com> [add license to DTS files, fix state_default and reduce to the mimimum, move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: don't create switch config for VIXMINIDavid Bauer2020-07-181-5/+2
| | | | | | | | | Don't create UCI switch config for the GL.iNet microuter-N300 and VIXMINI. These devices only have a single LAN port. Creating the switch config makes usage of VLANs more complicated, as they would have to be configured on the MAC as well as the "switch". Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Netgear R6020Tim Thorpe2020-07-102-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear R6020, aka Netgear AC750. The R6020 appears to be the same hardware as the Netgear R6080, aka Netgear AC1000, but it has a slightly different flash layout, and no USB ports. Specification: SoC: MediaTek MT7628 (580 MHz) Flash: 8 MiB RAM: 64 MiB Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E) LAN speed: 10/100 LAN ports: 4 WAN speed: 10/100 WAN ports: 1 UART (57600 8N1) on PCB MAC addresses based on vendor firmware: LAN *:88 0x4 WAN *:89 WLAN2 *:88 0x4 WLAN5 *:8a 0x8004 The factory partition might have been corrupted beforehand. However, the comparison of vendor firmware and OpenWrt still allowed to retrieve a meaningful assignment that also matches the other similar devices. Installation: Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet cable to connect to LAN port 1 of the R6020, and power the R6020 off. From the connected workstation, run `nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`, replacing eth0 with the appropriate interface (can be identified by running `nmrpflash -L`). Then power on the R6020. After flashing has finished, power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been installed, subsequent flashes can use the web interface and sysupgrade files. Signed-off-by: Tim Thorpe <timfthorpe@gmail.com> [slightly extend commit message, fix whitespaces in DTS, align From: with Signed-off-by] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE220 v2Rowan Border2020-06-302-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at> for the TP-Link RE200 v2 as both devices share the same SoC, flash layout and GPIO pinout. Specifications MediaTek MT7628AN (580 Mhz) 64 MB of RAM 8 MB of FLASH 2T2R 2.4 GHz and 1T1R 5 GHz 1x 10/100 Mbps Ethernet UART header on PCB (57600 8n1) 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. Web Interface Installation It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Signed-off-by: Rowan Border <rowanjborder@gmail.com>
* ramips: remove duplicate MAC assignment caseDavid Bauer2020-06-291-5/+2
| | | | | | | | Cudy WR1000 and Wavlink WL-WN577A2 store WAN as well as label MAC address at the same position in flash. Suggested-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for RAVPower RP-WD009David Bauer2020-06-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD009 is a batter-powered pocket sized router with SD card lot and USB port. Hardware -------- CPU: MediaTek MT7628AN RAM: 64M DDR2 FLASH: 16M GigaDevices SPI-NOR WLAN: MediaTek MT7628AN 2T2R b/g/n MediaTek MT7610E 1T1R n/ac ETH: 1x FastEthernet SD: SD Card slot USB: USB 2.0 Custom PMIC on the I2C bus (address 0x0a). Installation ------------ 1. Press and hold down the reset button. 2. Power up the Device. Keep pressing the reset button for 10 more seconds until the Globe LED lights up. 3. Attach your Computer to the Ethernet port. Assign yourself the address 10.10.10.1/24. 4. Access the recovery page at 10.10.10.128 and upload the OpenWrt factory image. 5. The flashing will take around 1 minute. The device will reboot automatically into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for WAVLINK WL-WN577A2Lars Wessels2020-06-292-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band wall-plug wireless router. In Germany this device is sold under the brand name Maginon WL-755 (white case): Device specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps (Ralink RT3050) - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER - Buttons: Reset, WPS - Small sliding power switch Flashing instructions (U-boot): - Configure a TFTP server on your PC/Laptop and set its IP to 192.168.10.100 - Rename the OpenWrt image to firmware.bin and place it in the root folder of the TFTP server - Power off (using the small sliding power switch on the left side) the device and connect an ethernet cable from its LAN or WAN port to your PC/Laptop - Press the WPS button (and keep it pressed) - Power on the device (using the small power switch) - After a few seconds, when the WAN/LAN LED stops blinking very fast, release the WPS button - Flashing OpenWrt takes less than a minute, system will reboot automatically - After reboot the WPS LED will indicate the current OpenWrt running status Signed-off-by: Lars Wessels <software@bytebox.org> [removed unused labels - fix whitespace errors - wrap commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Netgear R6080Alex Lewontin2020-06-272-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear R6080, aka Netgear AC1000. The R6080 has almost the same hardware as the Netgear R6120, aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and uses a different SERCOMM_HWID. Specification: SoC: MediaTek MT7628 (580 MHz) Flash: 8 MiB RAM: 64 MiB Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E) LAN speed: 10/100 LAN ports: 4 WAN speed: 10/100 WAN ports: 1 UART (57600 8N1) on PCB Installation: Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet cable to connect to LAN port 1 of the R6080, and power the R6080 off. From the connected workstation, run `nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`, replacing eth0 with the appropriate interface (can be identified by running `nmrpflash -L`). Then power on the R6080. After flashing has finished, power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been installed, subsequent flashes can use the web interface and sysupgrade files. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [rebase and adjust for 5.4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move Netgear R6120 LED trigger to DTSAlex Lewontin2020-06-231-6/+2
| | | | | | | | | | | | This moves the trigger for the Netgear R6120's wlan2g_green LED from base-files/etc/board.d/01_leds to the device-tree file. This has been applied to R6120 based on findings for the very similar Netgear R6080. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [merge case in 01_leds, slightly adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-161-2/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1Ernst Spielmann2020-05-242-9/+18
| | | | | | | | | | | | | | | | | | | | | | | | Specifications: - MT7628NN @ 580 MHz - 32 MB RAM - 8 MB Flash - 5x 10/100 Mbps Ethernet (built-in switch) - 2.4 GHz WLAN - 2x external, non-detachable antennas (1x for RT-N10P V3) Flash instructions: 1. Set PC network interface to 192.168.1.75/24. 2. Connect PC to the router via LAN. 3. Turn router off, press and hold reset button, then turn it on. 4. Keep the button pressed till power led starts to blink. 5. Upload the firmware file via TFTP. (Any filename is accepted.) 6. Wait until the router reboots. Signed-off-by: Ernst Spielmann <endspiel@disroot.org> [fix node/property name for state_default] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default switch setup in 02_networkChuanhong Guo2020-05-191-3/+0
| | | | | | | | ramips images now relies on explicit switch setup for proper failsafe functionality. Remove default cases where it relies on vlan setup in dts and add switch setup for devices affected. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: remove config-4.14 for mt7621/mt76x8Adrian Schmutzler2020-04-231-231/+0
| | | | | | | | | | | mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their DTS(I) files are incompatible to kernel 4.14. Remove the corresponding kernel config files to signal that more boldly and to prevent accidentally patching the wrong kernel when pulling in older config patches. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: explicitly disable built-in switch when neededChuanhong Guo2020-04-121-11/+9
| | | | | | | | | | previously we rely on the failsafe setup in preinit scripts to disable built-in switch implicitly for single-port devices. This doesn't work anymore due to preinit script removal. this patch explicitly disable built-in switch for needed devices. Fixes: a8d62a4eb1 ("ramips: remove set_preinit_iface script") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt76x8: switch to kernel 5.4Chuanhong Guo2020-04-121-0/+1
| | | | | | | 4.14 doesn't work anymore due to gpio dt binding changes. Switch mt76x8 to 5.4 directly. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: refresh kernel config for 5.4Chuanhong Guo2020-04-121-36/+48
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: copy kernel config for 5.4Chuanhong Guo2020-04-121-0/+231
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: move and rename out-of-tree mtk eth driverChuanhong Guo2020-04-121-5/+5
| | | | | | | move the driver into shared 'files' directory and rename all symbols from mediatek/mtk to ralink. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: move swconfig to subtargets except for MT7621DENG Qingfang2020-04-041-1/+1
| | | | | | | As MT7621 does not use swconfig anymore, move the package swconfig to other subtargets. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for TOTOLINK A3Sungbo Eo2020-03-131-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 3x 10/100Mbps - Switch: SoC internal Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Tested on device by JasonHCH <hsuan670629@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix HiWiFi HC5761A switch settingsDENG Qingfang2020-02-141-1/+4
| | | | | | HC5761A has only 2 LAN ports Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for TP-Link RE200 v2Andreas Böhler2020-02-012-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:0D 2.4G: *:0E 5G : *:0F Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Additonal notes --------------- It is possible to flash back to stock by using tplink-safeloader to create a sysupgrade image based on a stock update. After the first boot, it is necessary upgrade to another stock image, otherwise subsequent boots fail with LZMA ERROR 1 and you have to attach serial to recover the device. Signed-off-by: Andreas Böhler <dev@aboehler.at> [remove DEVICE_VARS change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use tpt DTS trigger for TP-Link TL-MR3020 v3 and TL-WA801ND v5Jan Alexander2020-01-301-7/+3
| | | | | | | | | | | | | | This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput LED trigger in order to react to all VAPs. It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the DTS and merges the now identical LAN LED configs. Verified these changes on a TL-MR3020v3. Signed-off-by: Jan Alexander <jan@nalx.net> [changed commit title and extended commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for GL.iNet microuter-N300David Bauer2020-01-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a pocket-size travel router. It is essentially identical to the VIXMINI (internally referred as MT300N-v3) but with double the RAM and SPI-flash. Additionally, set the label-mac for both the VIXMINI as well as the microuter-N300. Hardware -------- SoC: MediaTek MT7628NN RAM: 128M DDR2 FLASH: 16M LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for TP-Link RE305 v1Steffen Förster2020-01-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: MediaTek MT7628AN RAM: 64MiB Flash: 8MiB Wifi: - 2.4GHz: MT7628AN - 5GHz: MT7612EN LAN: 1x 10/100 Mbps Flash instructions: Flash factory image through stock firmware WEB UI. Back to stock is possible by using TFTP and stripping down the Firmware provided by TP-Link to a initramfs. The flash space between 0x650000 and 0x7f0000 is blank in the stock firmware so I left it out as well. Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>