aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* kernel: backport GD25Q256 support from 4.15Kuan-Yi Li2020-12-014-24/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | Backport below changes for GigaDevice GD25Q256 support from v4.15: e27072851bf7 mtd: spi-nor: add a quad_enable callback in struct flash_info 65153846b18c mtd: spi-nor: add support for GD25Q256 This chip is used on newer Quad-E4G boards. Before: [ 2.366493] m25p80 spi0.0: unrecognized JEDEC id bytes: c8, 40, 19 [ 2.372853] m25p80: probe of spi0.0 failed with error -2 After: [ 2.371722] m25p80 spi0.0: gd25q256 (32768 Kbytes) [ 2.376694] 5 fixed-partitions partitions found on MTD device spi0.0 [ 2.383043] Creating 5 MTD partitions on "spi0.0": [ 2.387824] 0x000000000000-0x000000030000 : "u-boot" [ 2.394138] 0x000000030000-0x000000031000 : "u-boot-env" [ 2.400608] 0x000000031000-0x000000040000 : "config" [ 2.406830] 0x000000040000-0x000000050000 : "factory" [ 2.413169] 0x000000050000-0x000002000000 : "firmware" Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* ramips: fix logic level for DIR-645 buttonsDavid Bauer2020-11-111-2/+2
| | | | | | | | | | | | The D-Link DIR-645 currently uses an incorrect logic level for its buttons. Correct them in order to prevent unintentional activation of failsafe mode. Reported-by: Perry Melange <isprotejesvalkata@gmail.com> Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 929e8f0f553637076f2612fb1c2225c5cee1f7ab)
* kernel: bump 4.14 to 4.14.200Koen Vandeputte2020-10-121-3/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Revert "ramips: ethernet: fix to interrupt handling"Jo-Philipp Wich2020-09-181-5/+6
| | | | | | | | | This reverts commit 7ac454014a11347887323a131415ac7032d53546. The change reportedly causes regressions in ethernet performance. Fixes: FS#3332 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: ethernet: fix to interrupt handlingNeilBrown2020-09-061-6/+5
| | | | | | | | | | | | | The current code acknowledged interrupts *after* polling. This is the wrong way around, and could cause an interrupt to be missed. This is not likely to be fatal as another packet, and so another interrupt, should come along soon. But maybe it is causing problems, so let's fix it anyway. Signed-off-by: NeilBrown <neil@brown.name> (Note that this matches the upstream driver.) Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: fix Xiaomi MiWiFi Mini switch definitionChih-Wei Chen2020-08-131-6/+6
| | | | | | | | | | | | | | | | | | | | | | Based on OpenWRT Table of Hardware > Xiaomi > Xiaomi Mi WiFi Mini Switch Ports Defaults: 0, 1: LAN 4: WAN 6: CPU Port in Web GUI (word printed on bottom of case) WAN(Internet) map to switch port 4 LAN1(.) map to switch port 1 LAN2(..) map to switch port 0 CPU map to switch port 6 current setting is 1 WAN/ 4 LAN port, fix it. Signed-off-by: Chih-Wei Chen <changeway@gmail.com> [rebased after base-files split, fixed commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (backported from commit 3e88ab79b03917bc4b03b34db12edf622bde1de1)
* kernel: update kernel 4.14 to version 4.14.193Hauke Mehrtens2020-08-111-1/+1
| | | | | | Compile and runtime tested on lantiq/xrx200 and ipq40xx. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: correct WizFi630S pin mappingsTobias Welz2020-08-081-27/+8
| | | | | | | | | | | | WizFi630S had some pins changed in the release version of the board. The run led, wps button and a slide switch where affected. This patch is correcting this. i2c is removed as it is sharing a pin with the run (system) led. uart2 is enabled as it is also enabled in the OEM firmware. Signed-off-by: Tobias Welz <tw@wiznet.eu> (backported from commit d0b229f553a814b22c16976e40a197f892c0c0df) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable flashing WizFi630S via OEM firmwareTobias Welz2020-08-081-0/+1
| | | | | | | | | | | | WIZnet WizFi630s board name is written slightly different it its OEM OpenWrt firmware. This causes an incompatibility warning during flashing with sysupgrade. This patch is adding the vendor board name to the supported devices list to avoid this warning. For initial flashing you can use sysupgrade via command line or luci beside of TFTP. Do not keep the OEM configuration during sysupgrade. Signed-off-by: Tobias Welz <tw@wiznet.eu> (cherry picked from commit 816973f42aa47d910d3e35c2f8f8eb9d67416396)
* ramips: remove doublet entry in WizFi630S dts fileTobias Welz2020-08-081-4/+0
| | | | | | | | &wmac entry in WIZnet WizFi630S dts file was existing two times. This is removing one of them. Signed-off-by: Tobias Welz <tw@wiznet.eu> (cherry picked from commit b735bbcb1876196f33f044ed07325f8959a8967f)
* ramips: disable unused phy ports of WizFi630STobias Welz2020-08-081-0/+1
| | | | | | | | WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports draw unnecessarily power. This is disabling the unused phy ports. Signed-off-by: Tobias Welz <tw@wiznet.eu> (cherry picked from commit 36d4c2272ec65490232e70d45b945b9f467b78f0)
* ramips: add kmod-usb-dwc2 to ZyXEL Keenetic imageAlexey Dobrovolsky2020-08-021-1/+2
| | | | | | | | | | | | ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should be in the default image for this device. Fixes: a7cbf59e0e04 ("ramips: add new device ZyXEL Keenetic as kn") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> [fixed whitespace issue] Signed-off-by: Petr Štetiar <ynezz@true.cz> (backported from commit 0a182fcba6d9cb2cf74cae9114ea4770ef928f75) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove patches for USB-dwc2Alexey Dobrovolsky2020-08-021-29/+0
| | | | | | | | | | | | | | | In FS#2738 we can see that patch first introduced in e8ebcff ("ramips: add a explicit reset to dwc2") breaks USB functionality since 18.06. Thus, this patch should be removed. Removed: - 0032-USB-dwc2-add-device_reset.patch Fixes: FS#2738 Fixes: FS#2964 Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> (cherry picked from commit ab841b4393a4077a5819da1da040ab9a89e3b69d)
* kernel: fix nand_release() usage.Hauke Mehrtens2020-07-041-2/+2
| | | | | | | | nand_release() takes nand_chip since commit 5bcfcbfc4019 ("mtd: rawnand: Pass a nand_chip object to nand_release()") Fixes: f4985a22ca1b ("kernel: Update kernel 4.14 to version 4.14.187") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Update kernel 4.14 to version 4.14.187Hauke Mehrtens2020-07-043-6/+6
| | | | | | | | | | Fixes: - CVE-2020-10757 Run tested: ath79, ipq40xx Build tested: ath79, ipq40xx Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: increase SPI frequency for ELECOM WRC-GST devicesINAGAKI Hiroshi2020-06-281-1/+1
| | | | | | | | | | | | Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST to 40 MHz by updating the common DTSI file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1900GST] Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [split patch, adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit b5ae70d0530d1a733816f921ae0fe4dd58251fbb)
* ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by defaultPetr Štetiar2020-05-261-9/+3
| | | | | | | | | | | | | | | | | | | | | | | | | Looking at the current upstream driver implementation, it seems like the TX/RX flow control is enabled only if the flow control pause option is resolved from the device/link partner advertisements (or otherwise set). On the other hand, our current in-tree driver force enables TX/RX flow control by default, thus possibly leading to TX timeouts if the other end sends pause frames (which are not properly handled?): WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324 NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out Disabling the flow control on PORT 5 MAC seems to fix this issues as the pause frames are then filtered out. While at it, I'm removing the if condition completely as suggested, since this code is run only on mt7621 SoC, so there is no need to check for the silicon revisions. Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12 Suggested-by: Felix Fietkau <nbd@nbd.name> Reported-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit c8f8e59816eca49d776562d2d302bf990a87faf0)
* ramips: drop non-existant ralink,port-map for Ravpower WD03Adrian Schmutzler2020-05-191-1/+0
| | | | | | | | | | | The property "ralink,port-map" has been obsolete long before this device was added, and the device is a one-port anyway. Just remove it. Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit c00b2df6c8e421ea7aa96f53178dc85db99f2305)
* kernel: bump 4.14 to 4.14.178Petr Štetiar2020-05-041-2/+2
| | | | | | | | | | | | | | Refreshed all patches and removed upstreamed: oxnas/001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch oxnas/002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch Fixes: CVE-2020-12114 and CVE-2020-11669 Runtime-tested on: qemu-x86-64 Compile-tested on: ath79/generic, x86/64, imx6 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: remove memory node for ZBT MT7621 devicesChuanhong Guo2020-04-283-15/+0
| | | | | | | | | | It's known that ZBT sells 256M variants of these routers. As a result, our images won't be able to boot on these routers. This commit removes memory node for them. With previously backported memory detection patch, kernel is able to detect memory size itself. Fixes: FS#3053 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027Sungbo Eo2020-04-271-1/+0
| | | | | | | | kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and Belkin F7C027 does not have a USB port anyway. Just drop it. Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit 1dedad2a00d8519d4892b8529b5f2fffcb768220)
* kernel: bump 4.14 to 4.14.176Koen Vandeputte2020-04-161-2/+2
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch - 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch - 003-ARM-dts-oxnas-Fix-clear-mask-property.patch Fixes: - CVE-2020-8647 - CVE-2020-8648 (potentially) - CVE-2020-8649 Compile-tested on: cns3xxx, octeontx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Revert "ramips: disable ZyXel Keenetic by default"Adrian Schmutzler2020-04-121-1/+0
| | | | | | | | | This reverts commit c38074de929e6f7c089e2cb7f81746ba90ddf16b. Since ZyXEL Keenetic has actually 8 MiB flash as fixed in the previous patch, we can re-enable it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use full 8MB flash on ZyXEL KeeneticAlexey Dobrovolsky2020-04-122-2/+2
| | | | | | | | | | | | | | | | | ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB. This commit fixes the problem. WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is an article with specs [2] (in Russian). [1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic [2] https://3dnews.ru/608774/page-2.html Fixes: FS#2487 Fixes: a7cbf59e0e04 ("ramips: add new device ZyXEL Keenetic as kn") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> (cherry picked from commit fea232ae8feb6af780fd4fa78ebe9231778bf75a)
* kernel: bump 4.14 to 4.14.171Koen Vandeputte2020-02-245-14/+14
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2013-1798 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: append tail to WF2881 initramfs imageSungbo Eo2020-02-211-0/+8
| | | | | | | | | | | | | Stock firmware has a vendor-defined tail at the end of uImage for image validation. This patch enables OpenWrt installation from stock firmware without having to access the UART console. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit be3e98ce26da5e737744427e1d59dd1c0508edef)
* ramips: reenable image creation for the D-Link DIR-645Mason Clarke2020-02-011-1/+0
| | | | | | | | | | | | | | | | | | | This commit reenables the image creation for the D-Link DIR-645. Images built for the D-Link DIR-645 work just fine, there is no reason to disable the image creation for it. I tested the OpenWrt 18.06.5 and 19.07.0-rc1 images, as well as an image I built from the current 19.07 branch (git HEAD 62d5ece) with the default 19.07 release config, and I cannot confirm the report that commit 2607c02ed599b6118ba26e2f35e7c828c21d7275 ("ramips: disable D-Link DIR-645 by default") references. Configuration changes were applied successfully and remained set after a reboot as well. The log also showed no anomalies. This reverts commit 2607c02ed599b6118ba26e2f35e7c828c21d7275. Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
* ramips: use tpt DTS trigger for TP-Link TL-MR3020 v3 and TL-WA801ND v5Jan Alexander2020-01-303-6/+4
| | | | | | | | | | | | | | | | | This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput LED trigger in order to react to all VAPs. It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the DTS and merges the now identical LAN LED configs. Verified these changes on a TL-MR3020v3 and TL-WA801NDv5. Signed-off-by: Jan Alexander <jan@nalx.net> [changed commit title and extended commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [added comment about test result on TL-WA801ND v5] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 20eb45da4fc19c12ea2073471992eeaf9d602fa5)
* ramips: remove duplicate DEVICE_PACKAGES for TP-Link Archer C20iAdrian Schmutzler2020-01-291-1/+0
| | | | | | | | | | DEVICE_PACKAGES is specified twice for the same device. Remove the first (=older) assignment. Fixes: 40692f0fb55c ("ramips: mt7620: select only the matching mt76 driver") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 4ecd6510bf8877dcd07561045852726ffbab8814)
* ramips: mt7621: ubnt-erx: allow sysupgrade from masterPetr Štetiar2020-01-241-0/+2
| | | | | | | | | | | | Currently it's not possible to downgrade from master: Device ubiquiti,edgerouterx not supported by this image Supported devices: ubnt-erx So fix it by adding a DTS based device name from master into SUPPORTED_DEVICES list. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: rt305x: remove unnecessary mediatek,portmapSungbo Eo2020-01-212-2/+0
| | | | | | | | | | "#mediatek,portmap" is not a valid property name. If mediatek,portmap equals 0x0, then the esw driver ditches it and uses the default value, 0x3f. Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit f87281b2956110f10af9eb23fc6d327dfde7ab42)
* ramips: mt76x8: fix bogus mediatek,portmapSungbo Eo2020-01-2117-13/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with string values. Convert the strings to integers to make it work. According to its switch setup, WRTnode 2P/2R have a WAN port at port 0, so the correct value should be 0x3e. tplink_8m.dtsi uses "llllw", but it does not match switch setups of any device using the DTSI. Remove it from the DTSI and add correct value to DTS for each device. These devices have a WAN port at port 0. Set the value to 0x3e. - tplink,archer-c20-v4 - tplink,archer-c50-v3 - tplink,tl-mr3420-v5 - tplink,tl-wr840n-v4 - tplink,tl-wr841n-v13 - tplink,tl-wr842n-v5 These devices have only one ethernet port. They don't need portmap setting. - tplink,tl-wa801nd-v5 - tplink,tl-wr802n-v4 - tplink,tl-wr902ac-v3 Signed-off-by: Sungbo Eo <mans0n@gorani.run> (backported from commit 7a387bf9a0d73f7c581e2c9aeae6476588100e2c) [removed TL-WR841N v14 which is not present in 19.07] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix portmap for TP-Link Archer C50 v4Maxim Anisimov2020-01-211-1/+1
| | | | | | | According to 02_network portmap is wan=0 lan1=1 lan2=2 lan3=3 lan4=4 Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com> (cherry picked from commit ebf535a6cfefef5b0afb74cb01c9a17ab242b85b)
* ramips: mt7620/mt7621: remove invalid mediatek,portmapSungbo Eo2020-01-211-3/+2
| | | | | | | | | | | | | mt7620 and mt7621 use mt7530 driver, which only accepts "llllw", "wllll", and "lwlll" values. According to its switch setup, Mi Router 3G v2 has a WAN port at port 4, so the correct value should be "llllw". Signed-off-by: Sungbo Eo <mans0n@gorani.run> (backported from commit d3c0a944059bb0d45c3b56278249100258378b0c) [removed devices not in 19.07] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add factory image for Netgear R6350Christoph Krapp2020-01-211-1/+6
| | | | | | | | | | | | | | This adds factory image generation for all three devices. These images can be flashed via WebUI for easy installation. Thanks to David Bauer for the inspiration. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [altered commit to only include the R6350] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 3c8df280a96bbd81357d6eb52845e6b5fa7162fe) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add mt7615e support to Netgear R6350Christoph Krapp2020-01-212-1/+10
| | | | | Signed-off-by: Christoph Krapp <achterin@googlemail.com> (cherry picked from commit 9861fa7abab97cb928aaa6cd5732a413d973ac95)
* ramips: fix HiWiFi HC5962 status LEDDENG Qingfang2020-01-181-3/+4
| | | | | | | | | | Match LED behavior to stock firmware: Red: booting White: running Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> (cherry picked from commit 9a3c9a96563c3c3fb1e15b791d9117b193fed7a6)
* ramips: fix HiWiFi HC5962 switch configurationDENG Qingfang2020-01-181-1/+4
| | | | | | | | HC5962 has only 3 LAN ports, switch port 0 is unused Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> (backported from commit 68f49df31507454f86b72a5c1e250505176baed7) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add kmod-mt7615e to Xiaomi Mi Router 3 Pro imagesOzgur Can Leonard2020-01-182-3/+5
| | | | | | | Now that the mt76/mt7615e driver is in Openwrt, might as well use it. Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> (cherry picked from commit d7c082ba4f7de97b3708d1f4a064954ffc774778)
* ramips: fix wps leds/btn for TP-Link TL-WA801ND v5Jan Alexander2020-01-171-4/+16
| | | | | | | | | | | - fix color and active mode for existing wps led - add green wps led - add wps button Signed-off-by: Jan Alexander <jan@nalx.net> [wrap line] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 26105974e7f9758cd4bc443ce0322983f818acd5)
* ramips: mt7621: disable images for gehua_ghl-r-001Petr Štetiar2020-01-141-0/+1
| | | | | | | | | | | This device OOPs during the boot due to broken flash. It can be probably fixed with `broken-flash-reset` once ramips is on 4.19 kernel. So disable images for this device until its fixed. Ref: FS#2695, PR#2483 Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 28080d54d217fb4ab112e079f69462fee695dbf8)
* ramips: fix leds for TP-Link Archer C20 v4Maxim Anisimov2020-01-122-2/+3
| | | | | | | | | | | - add "gpio" group for wan_orange led - use tpt triggers for wifi led indication - add wifi 5 GHz led support Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com> [slight commit message adjustment, backport] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 3a538db60abfc50b47ce1774f66d489700a50c00)
* ramips: Fix sysupgrade for Xiaomi mir3gHauke Mehrtens2020-01-061-3/+4
| | | | | | | | | | | | | | | | | | | This mostly reverts the original commit e9929ebeeaef ("ramips: Fix sysupgrade for Xiaomi mir3g") and replaces it with setting the BOARD_NAME to the old value. This way the folder in the tar will be named sysupgrade-mir3g and not sysupgrade-xiaomi_mir3g and the sysupgrade in OpenWrt 18.06 can find it. Without this change sysupgrade from 18.06 to 19.07 is only possible with the -F option. I tested the following sysupgrades successfully without -F 18.06 -> 19.07 19.07 -> master master -> 19.07 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: Fix sysupgrade for Xiaomi mir3gHauke Mehrtens2020-01-051-3/+3
| | | | | | | | | | | | | | | | | Without this change sysupgrade from 18.06 to 19.07 is only possible with the -F option. In OpenWrt 18.06 the nand_do_platform_check() function is called with the board name mir3g only, if the tar does not use mir3g it will fail. OpenWrt 19.07 and later support the metadata with the supported_devices attribute to allow renaming. Do the renaming of the target between 19.07 and master like it is done for some other boards. I tested the following sysupgrades successfully without -F 18.06 -> 19.07 19.07 -> master master -> 19.07 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: remove duplicate dts nodes of MediaTek LinkIt Smart 7688Jack Chen2020-01-051-4/+0
| | | | | | | | There are two identical wmac nodes in the dts file of MediaTek LinkIt Smart 7688, so delete one of them. Signed-off-by: Jack Chen <redchenjs@live.com> (cherry picked from commit 4be271a4867dcf57a122eeb7b42407e7a506915e)
* ramips: fix Archer C20i wireless MAC addressDavid Bauer2020-01-031-0/+3
| | | | | | | | | | | The TP-Link Archer C20i previously had a generic Ralink MAC address set for both radios, as the caldata does only contain a generic MAC address. Set the MAC address from the vendor firmware for both radios to assign unique MAC addresses to every device. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 3b013dcdf8d8aa0e3601e3aac30342318025e32a)
* ramips: fix Archer C2 v1 5GHz MAC addressDavid Bauer2020-01-031-0/+2
| | | | | | | | | | | | The TP-Link Archer C2 v1 previously had a generic Ralink MAC address set for the 5GHz radio (MT7610), as the caldata does only contain a generic MAC address. Set the MAC address from the vendor firmware for the 5GHz radio to assign unique MAC addresses to every device. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit dcc923a4c45b48fcbef4f3964f74fbcaabad335e)
* ramips: add system LED indicators for TP-Link C20iDavid Bauer2020-01-031-1/+8
| | | | | | | | Use the WPS LED to indicate system status like it is done for the TP-Link Archer C2 v1 and many other boards. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit a272fafc9c507820cc62aa12464588bac45f250a)
* ramips: convert TP-Link MT7620 boards to tpt triggerDavid Bauer2020-01-036-5/+7
| | | | | | | | | | | | | This converts all MediaTek MT7620 boards from TP-Link to use the now supported WiFi throughput LED trigger. This way, the LED state now covers all VAPs regardless of their name. Also align all single-WiFi LEDs to represent the state of the 2.4GHz radio. This was not always the case previously, as later-added support for the MT7610 altered the phy probing order. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 1e7c6381f0058e49caab8de54eaad4862732f95d)
* ramips: fix inverted reset button for Ravpower WD03Moritz Warning2020-01-031-1/+1
| | | | | | | The button events "pressed" and "released" were switched. Tested with v18.06.4. Signed-off-by: Moritz Warning <moritzwarning@web.de> (cherry picked from commit 3e1325b219fced91f01d5594503f61d326a93b90)
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 12:29:06 +0000