aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/tegra/config-4.14
Commit message (Collapse)AuthorAgeFilesLines
* tegra: add support for CompuLab TrimSliceTomasz Maciej Nowak2019-04-061-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is a small form factor computer with rich amount of expansion ports. Some hardware specs and supported features in this commit: CPU: NVIDIA Tegra 2 @ 1GHz RAM: 1GB DDR2-667 Storage: SDHC card slot µSDHC card slot USB to SATA bridge (depends on model) 1MB SPI NOR flash for bootloader (single partition) LAN: RTL8111DL GbE WIFI: RT3070 b/g/n with external antenna (depends on model) RTC: EM3027 (mapped as rtc0; with battery backup) Tegra 2 built-in (mapped as rtc1) Sound: Analog/Digital (TLV320AIC23b; S/PDIF not tested) Connectors: 4x USB 2.0 RS232 (mini serial) HDMI DVI-D (depends on model, not supported atm) Extension connector (24 pin ZIF, 0.5mm pitch): 2X UART SPI JTAG (1.8V) Other: power button with green led (not functional for early revisions without programmed PMIC) 2x GPIO configurable green led TrimSlice uses U-Boot placed in NOR flash. Boots Linux from any media connected to USB, SATA or SD card inserted in slot. Can also boot from TFTP. To run OpenWrt one needs to update U-Boot to fairly recent version (the versions, pre-dts/dts provided by CompuLab won't suffice): 1. Boot TrimSlice into Your current linux distro, 2. Download trimslice-spi.img from u-boot-trimslice subdir, 3. Install mtd-utils, 4. Run following commands: flash_erase /dev/mtd0 0 256 nandwrite /dev/mtd0 trimslice-spi.img 5. Poweroff, insert SD card with OpenWrt, boot and enjoy. If by some obstacle You can't follow those instructions, it is possible to flash U-Boot using serial console. 1. Insert FAT or EXT2/EXT3 formatted SD card with trimslice-spi.img, 2. Interrupt boot process to enter U-Boot command line, 3. Run following commands: ${fs}load mmc 0 0x04080000 trimslice-spi.img sf probe 0 sf erase 0 0x100000 sf write 0x04080000 0x0 ${filesize} reset 4. Poweroff, insert SD card with OpenWrt, boot and enjoy. If something went wrong with one of above steps, there is simple recovery option: 1. Open the µSD slot security door to access the recovery-boot button, 2. Insert SD card with OpenWrt to the front slot while unpowered, 3. Power on the TrimSlice while pressing the recovery-boot button, 4. With this it should boot straigth to OpenWrt, from there download trimslice-spi.img and execute following commands: mtd erase /dev/mtd0 mtd write trimslice-spi.img /dev/mtd0 5. Reboot, now it should boot straigth to OpenWrt, without pressing the recovery-boot button, with proper U-Boot flashed. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* tegra: add new targetTomasz Maciej Nowak2019-04-061-0/+556
New target introduces initial support for NVIDIA Tegra SoC based devices. It focuses on Tegra 2 CPUs, for successors supporting NEON instruction set the target should be split in two subtargets. This initial commit doesn't create any device image, it's groundwork for further additions. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>