aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
...
* kernel: bump 4.9 to 4.9.150Koen Vandeputte2019-01-1616-164/+41
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch Altered patches: - 024-7-net-reorganize-struct-sock-for-better-data-locality.patch Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 3.18 to 3.18.132Koen Vandeputte2019-01-162-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested: adm5120 Runtime-tested: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* firmware-utils: mksercommfw: overhaul image creationMathias Kresin2019-01-151-9/+14
| | | | | | | | | | | | | | | | | | | | Move the zip compression into a build recipe. Pad the image using the existing build recipes as well to remove duplicate functionality Change the code to append header and footer in two steps. Allow to use a fixed filename as the netgear update image does. Use a fixed timestamp within the zip archive to make the images reproducible. Due to the changes we are now compatible to the gnu89 c standard used by default on the buildbots and we don't need to force a more recent standard anymore. Beside all changes, the footer still looks wrong in compare to the netgear update image. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.93Stijn Tintel2019-01-1446-323/+104
| | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch - pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch - brcm2708/950-0415-qmi_wwan-apply-SET_DTR-quirk-to-the-SIMCOM-shared-de.patch Compile-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64 Runtime-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* sunxi: Add support for kernel 4.19Hauke Mehrtens2019-01-136-0/+827
| | | | | | | | This adds supprot for kernel 4.19 to the sunxi target. The patches and the configuration were copied from the kernel 4.14 patches folder and adapted for kernel 4.19. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Refresh kernel 4.14 configurationHauke Mehrtens2019-01-133-10/+5
| | | | | | | Refresh the sunxi kernel configuration without doing any intentional changes. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Use kernel specific sub target configurationHauke Mehrtens2019-01-133-0/+0
| | | | | | | | To make it easier to support multiple kernel versions in parallel also copy the sub target specific kernel configurations into kernel specific files. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Remove unneeded patchesHauke Mehrtens2019-01-132-118/+0
| | | | | | | | | | | | In the device tree file the higher offsets of the reset controller are not used, so this patch supporting higher bits is not needed. The sunxi architecture switched to the simple reset controller with kernel 4.19 and then this patch does not apply any more. The sunxi target in OpenWrt is very close to mainline, so if the device tree files from the mainline Linux kernel need this the mainline kernel will get support for this. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel/modules: Add missing config optionHauke Mehrtens2019-01-131-0/+1
| | | | | | | | This configuration option was added in kernel 4.15 and is missing in the kernel 4.19 configuration. Fixes: ed2839ac419 ("kernel/modules: add kmod-pmbus-zl6100 module") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* malta: Add support for kernel 4.19Hauke Mehrtens2019-01-131-0/+331
| | | | | | | | | | | This adds a kernel configuration file for kernel 4.19 on malta. CONFIG_POWER_RESET_PIIX4_POWEROFF and CONFIG_POWER_RESET_SYSCON were activated because malta now uses this driver for reboot. CONFIG_BLK_DEV_SR was also added because it was also added to the kernel default configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* malta: Refresh kernel 4.14 configurationHauke Mehrtens2019-01-133-5/+38
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: MIPS: Add CPU option reporting to /proc/cpuinfoHauke Mehrtens2019-01-133-0/+416
| | | | | | | | | | | Many MIPS CPUs have optional CPU features which are not activates for all CPU cores. Print the CPU options which are implemented in the core in /proc/cpuinfo. This makes it possible to see what features are supported and which are not supported. This should cover all standard MIPS extensions, before it only printed information about the main MIPS ASEs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel/modules: Fix build of kmod-pmbusHauke Mehrtens2019-01-131-1/+1
| | | | | | | | This fixes two build problems introduced with the recently added new kernel module package. Fixes: ed2839ac4190 ("kernel/modules: add kmod-pmbus-zl6100 module") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* generic: ar8216: ar8327: kill warningsChuanhong Guo2019-01-131-3/+3
| | | | | | This fixed warnings caused by returning value in a void function Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mpc85xx: add support for Sophos RED 15w Rev.1David Bauer2019-01-1314-3/+419
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: 4.14: sync configChristian Lamparter2019-01-131-2/+1
| | | | | | | This patch syncs the 4.14 kernel config to the current generic configuration. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: disable initramfs image in TL-WDR4900Pawel Dembicki2019-01-131-0/+1
| | | | | | | | | | Initramfs image isn't required for this device and regular initramfs generation isn't work properly. It create not working binaries. This patch disable initramfs image for TL-WDR4900. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mpc85xx: add support for Freescale (NXP) P2020RDBPawel Dembicki2019-01-137-1/+411
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit add initial support for Freescale (NXP) P2020RDB Hardware: SoC: P2020 2x1GHz DRAM: 512-1GB DDR3 2 + 4 GBE (2 separate ports and four in VSC7385) Flash: 16MB NOR, 32MB NAND, 16MB SPI-NOR PCIE x1 and mPCIE x1 SD Reader Interfaces: GBE RJ45 x6 USB2.0 x1 UART x2 I2C x2 JTAG x1 SD x1 PCIE x2 (PCIE and mPCIE) Flash instructions: Place sysupgrade image to 0x80000 address in NOR. Eg. (no brakelines in setenv command): setenv 'firmware_flash tftpboot $loadaddr $firmwarefile; protect off $norfdtaddr +$filesize; erase $norfdtaddr +$filesize; cp.b $loadaddr $norfdtaddr $filesize; protect on $norfdtaddr +$filesize; cmp.b $loadaddr $norfdtaddr $filesize' setenv firmwarefile firmware.bin run firmware_flash Boot (no brakeline in setenv command): setenv bootcmd 'setenv bootargs root=/dev/mtdblock3 rw console=$consoledev, $baudrate rootfstype=squashfs $othbootargs; bootm $norfdtaddr' saveenv boot Known issues: -Switch is unmanaged (VSC 7385 is connected via eLBC, driver uses SPI) -No SD reader support Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [refreshed patches]
* kernel/modules: add kmod-pmbus-zl6100 modulePawel Dembicki2019-01-134-0/+56
| | | | | | | | | | | | This patch adds the kmod packaging for the Intersil / Zilker Labs ZL6100 and compatible digital DC-DC controllers as well as the core kernel module for the Power Management Bus. Add: kmod-pmbus-core kmod-pmbus-zl6100 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* x86: Add support for kernel 4.19Hauke Mehrtens2019-01-129-0/+1847
| | | | | | | | | | | | This adds initial support for kernel 4.19 to the x86 target. The patches and the kernel configurations were copied from kernel 4.14 and then refreshed. The legacy and the genode target will not support PAE any more because they use a CPU type which does not support PAE, the generic sub target still supports PAE. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* x86: Refresh kernel 4.14 configurationHauke Mehrtens2019-01-126-26/+12
| | | | | | | | | | | | This refreshes the kernel configuration for kernel 4.14. First this was run for the legacy target: make kernel_oldconfig Then for all targets including the legacy target this was run: make kernel_oldconfig CONFIG_TARGET=subtarget The option CONFIG_104_QUAD_8 was added to the generic configuration because it would have been automatically removed. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* x86: Use kernel specific subtarget configurationsHauke Mehrtens2019-01-124-0/+0
| | | | | | | | | | This makes it possible to use different sub target configurations for kernel 4.19 for example. To support kernel 4.9 and kernel 4.14 with the same configuration file already needed some extra work this will not be needed for kernel 4.19 any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* octeon: fix typo in platform.shHans Dedecker2019-01-121-1/+1
| | | | | | Fix upgrade typo Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: add bcma fix for subdevices DMA parametersRafał Miłecki2019-01-112-10/+80
| | | | | | This fixes bgmac DMA allocations with kernel 4.19. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport bcma patches that improve printing functionsRafał Miłecki2019-01-105-1/+471
| | | | | | | Updated printing functions use dev_* helpers to provide more meaningful messages. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* brcm47xx: backport MIPS fix adding struct device for the SoCRafał Miłecki2019-01-102-2/+140
| | | | | | | | | | | It's needed to: 1) Fix GPIOLIB_IRQCHIP as in 4.19 there is no bcma revert anymore 2) Fix /sys/devices/ 3) Fix dma_zalloc_coherent() regression It still needs a bcma change that will follow later. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* brcm47xx: backport a final/accepted Netgear WNDR3400v3 patchRafał Miłecki2019-01-102-4/+22
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* cns3xxx: use actual size reads for PCIeKoen Vandeputte2019-01-072-0/+102
| | | | | | | | | | | | | | | | | | | upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors") reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(), which preserved the property of only doing 32-bit reads. It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(), so it changed writes from always being 32 bits to being the actual size, which works just fine. Due to: - The documentation does not mention that only 32 bit access is allowed. - Writes are already executed using the actual size - Extensive testing shows that 8b, 16b and 32b reads work as intended It makes perfectly sense to also swap 32 bit reading in favor of actual size. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.91Koen Vandeputte2019-01-0712-111/+22
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.148Koen Vandeputte2019-01-074-56/+8
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 902-debloat_proc.patch Removed upstreamed: - 424-v4.20-net-dsa-fix-88e6060-roaming.patch Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 3.18 to 3.18.131Koen Vandeputte2019-01-072-6/+7
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 902-debloat_proc.patch Compile-tested on: adm5120 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: whitespace cleanup inside hnat driverJohn Crispin2019-01-071-6/+8
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add two-way hashing scheme for MT7621HsiuWen Yen2019-01-071-0/+11
| | | | | | | | | | Sometimes the tuples might be hashed to the same FOE entry. When this hash collision problem occurs, some of the connections will not be bound and consequently the CPU idle rate cannot reach 100%. Therefore, two-way hashing is adopted to alleviate this problem. Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
* ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGEDavid Bauer2019-01-061-2/+2
| | | | | | | | | | | | Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from there) to fix image generation using the image-builder. Also remove the bootloader from DEVICE_PACKAGES and instead use the BUILD_DEVICES directive from within the U-Boot makefile. This fixes eva-image generation using the OpenWRT image-builder. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: 4.19: refresh kernel configChristian Lamparter2019-01-051-67/+29
| | | | | | | This patch syncs the 4.19 kernel config to the current generic configuration. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: 4.14: refresh kernel configChristian Lamparter2019-01-051-19/+24
| | | | | | | This patch syncs the 4.14 kernel config to the current generic configuration. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: 4.14: Sync kernel configRobert Marko2019-01-051-0/+2
| | | | | | | | This patch syncs the 4.14 kernel config to the current generic configuration. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* ipq40xx: 4.19: Sync kernel configRobert Marko2019-01-051-7/+0
| | | | | | | | | This patch syncs the 4.19 kernel config since the KERNEL_STACKPROTECTOR and compiler options are now part of the 4.19 generic config. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* ipq40xx: fix 4.14 ImageBuilder build woesChristian Lamparter2019-01-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | Robert Marko reported an issue with the current imagebuilder images: "Imagebuilder includes the new kmod-usb-dwc3-qcom USB driver package by default even on 4.14. [...] the current state imagebuilder can't build images under 4.14 at all as the kmod-usb-dwc3-qcom does not exist in it so it throws and error and exits." This patch reverts the Makefile to just kmod-usb-dwc3-of-simple and once the switch to 4.19 is done. It also removes the kmod-usb-phy-qcom-dwc3 as they only contain the usb-phy drivers for the ipq806x generation. Dynamic switching based on the KERNEL_PATCHVER is possible by using: $(if $(filter 4.14,$(KERNEL_PATCHVER)),kmod-usb-dwc3-of-simple,kmod-usb-dwc3-qcom) though it Fixes: 13321fa1429 ("ipq40xx: Use kmod-usb-dwc3-qcom by default") Fixes: 6e58fb2c33e ("ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom") Reported-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MBL: fix kernel/apollo3g.dtb artifact buildChristian Lamparter2019-01-051-1/+1
| | | | | | | | The name for the artifact should have been apollo3g.dtb and not kernel.dtb. Fixes: 908bdbfce9f9 ("apm821xx: utilize build ARTIFACTs") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add kernel 4.19 supportPawel Dembicki2019-01-055-0/+526
| | | | | | | | | | | | | | | Copied config from 4.14 Add patches for 4.19 Drop patch 103-powerpc-fix-build-cross32ar.patch, because issue was fixed in upstream. Compiled: generic p1020 Compiled and tested: (unofficial) P2020, TP-Link TL-WDR4900 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* mpc85xx: tl-wdr4900-v1: convert to mtdsplit imagePawel Dembicki2019-01-053-52/+62
| | | | | | | | | | | | | | | Currently, the image creation process for the TP-Link tl-wdr4900-v1 needs a fixed sized kernel and places the rootfs partition at a fixed offset. With the upcoming move to 4.19 the kernel will no longer fit into the existing allocated space for the kernel partition. This patch converts the device to utilize the established tplink,firmware mtdsplitter, which can deal with a dynamic kernel/rootfs size. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* ath79: add support for devolo WiFi pro 1200iDavid Bauer2019-01-054-0/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1750iDavid Bauer2019-01-054-1/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: cleanup the RB750Gr3 supportAnton Arapov2019-01-053-24/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | Always enable the pwr led and use the usr led for boot status indication. Rename nodes in the dts, to match what is recommend in the devicetree specification. Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io which isn't required on mt7621. Use the BTN_0 keycode for the mode button. This board doesn't have any wireless. Use a more descriptive label for the reset button and the GPIO enabling the usb vcc supply. Use the beeper kernel module for the buzzer. Fix the pinmux to switch only pins used as GPIOs to the GPIO function. Add support for the PoE enable GPIO to the userspace. The PoE power status can be read via GPIO7. Since OpenWrt doesn't have support for reading inputs from userspace, prepare only the pinmux for the GPIO. Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add RB750Gr3 native supportAnton Arapov2019-01-055-31/+48
| | | | | | | | | | | | | | | | | This patch adds support of MikroTik RouterBOARD 750Gr3, without the need to reflashing the bootloader. Installation through RouterBoot follows the usual MikroTik method https://openwrt.org/toh/mikrotik/common Since the image isn't compatible with RouterBOARD 750Gr3 installations which have replaced the bootloader, the former used userspace boardname is not added to the SUPPORTED_DEVICES, to prevent a brick while trying to upgrade to the image with native support. Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: merge cases in 02_networkPaul Wassi2019-01-021-16/+6
| | | | | | Merge some duplicate cases in /etc/board.d/02_network Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* x86: enable kmod-bnx2 on 64-bit by defaultAlberto Bursi2019-01-021-1/+1
| | | | | | | Gigabit ethernet adapters using BCM5706/5708/5709/5716 chipset are common on servers and as easy/cheap to get as Intel based ones. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kernel: mtd: add support for EN25QH64 in spi-nor.cRoger Pueyo Centelles2019-01-022-0/+20
| | | | | | | | | | The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip. Its 32, 128 and 256 Mbits siblings are supported upstream but this particular size wasn't. This commit includes patches for kernels 4.14 and 4.19. Tested on a COMFAST CF-E120A v3 (ath79). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: align GL-AR750S boardname to other GL.iNet devicesChristoph Krapp2019-01-014-10/+7
| | | | | | As the official device name is GL-AR750S, rename the board accordingly. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 20:37:53 +0000