| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
| |
The RouterBOARD M33G has an additional UART that should be enabled
by default.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
SoC: QCA9533
DRAM: 32Mb DDR1
Flash: 8/16Mb SPI-NOR
LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC)
on GMII
WAN: 1x 10/100Mbps via MII
WLAN: QCA9530
USB: 1x 2.0
UART: standard QCA UART header
JTAG: yes
Button: 1x WPS, 1x reset
LEDs: 8x LEDs
A version with 4Mb flash is also available, but due to lack of
enough space it's not supported.
As the original flash layout does not provide enough space for
the kernel (1472k), the firmware uses OKLI and concat flash to
overcome the limitation without changing the boot address of the
bootloaders.
Installation:
1. Original bootloader
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP
tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
Reboot the board.
2. pepe2k's u-boot_mod
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP, as "firmware.bin"
run fw_upg
Reboot the board.
For the 16M version of the board, please use
openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE,
set up IMAGE/factory.bin without metadata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
|
|
|
|
|
|
|
|
|
| |
ar8xxx_soft_reset is effectively a NOP function. In the PHY state
machine, the availability and result of a soft_reset function
makes no difference for the code flow.
Thus, we can safely remove this method.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Modifying PHY capabilities in the probe function broke with upstream
commit 92ed2eb7f4b7 ("net: phy: probe the PHY before determining the
supported features").
AR8316 switches only support 10/100 Mbit/s link modes because of this
change.
Provide a get_features method for the PHY driver, so Gigabit link mode
will be advertised to link partners again.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
| |
Run `make kernel_oldconfig CONFIG_TARGET=subtarget`
This mostly aims at getting rid of redundant/unneeded symbols.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Add missing symbol CONFIG_AHCI_XGENE.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[also add for 5.10, remove from layerscape target config]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
wireless router. This device is also sold under the name SilverCrest
SWV 733 A2.
Device Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
- Buttons: Reset, WPS
- Sliding mode switch: AP, repeater, client
- Small sliding power switch
Flashing instructions:
U-Boot launches TFTP client if WPS button is pressed during power-on.
Configure as follows:
- Server IP: 192.168.10.100
- Filename (rename sysupgrade file to this): firmware.bin
Flashing should not take more than a minute, device will reboot
automatically.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
|
|
|
|
|
|
|
|
| |
Automatically refreshed:
generic/hack-5.10/902-debloat_proc.patch
generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
|
|
|
| |
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
|
| |
The patch was not applied to the v5.4 target, thus breaking Kernel 5.4
on devices with multiple flash chips attache to the SPI bus.
Fixes commit bd54e739541b ("ath79: set number of chipselect lines")
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
JCG Q20 is an AX 1800M router.
Hardware specs:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HV 128 MiB
RAM: Winbond W632GU6NB-11 256 MiB
WiFi: MT7915 2.4/5 GHz 2T2R
Ethernet: 10/100/1000 Mbps x3
LED: Status (red / blue)
Button: Reset, WPS
Power: DC 12V,1A
Flash instructions:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
MAC addresses map:
0x00004 *:3e wlan2g/wlan5g
0x3fff4 *:3c lan/label
0x3fffa *:3c wan
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications
SoC: MT7621
CPU: 880 MHz
Flash: 16 MiB
RAM: 128 MiB
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac
MT7603E / MT7615E
Ethernet: 5x Gbit ports
Installation
There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.
R4 & R5 need to be shorted (0-100Ω) for the UART to work.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[remove non-required switch-port node - remove trgmii phy-mode]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.
Installation:
------------
Install the OpenWrt factory image for C6U is from the
TP-Link web interface.
1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.
Recovery to stock firmware:
--------------------------
The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:
1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.
2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.
MAC addresses:
-------------
OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The patch adds support for the TP-Link Archer A6 v3
The router is sold in US and India with FCC ID TE7A6V3
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated from serial console only.
Press 'x' while u-boot is starting
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Thanks to: Frankis for Randmon MAC address fix.
Signed-off-by: Vinay Patil <post2vinay@gmail.com>
[remove superfluous factory image definition, whitespacing]
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes Gateworks Ventana 'DEVICE_NAME' variable which value wasn't
adjusted during migration to common 'vendor_model' image naming scheme
(fixes: FS#3825).
Furthermore, drop unused 'Build/boot-scr' recipe, get rid of redundant
'BOOT_SCRIPT' variable (use already provided 'DEVICE_NAME' instead) and
drop custom 'DEVICE_NAME' variable from SolidRun CuBox-i image recipe
(use default one instead).
Fixes: cbc8bcfbaa ("imx6: image: use vendor_model scheme")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
This updates the patches to match the versions included in the mtd
subsystem for the next Linux kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
| |
Rid of kernel error message:
[ 0.780828] orion-mdio d0072004.mdio: IRQ index 0 not found
on Marvell targets backporting the kernel commit fa2632f74e57
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
| |
The higher 16-bit of EEE register was overwritten by mistake, fix that.
Fixes: 5b9ba4a93e83 ("generic: mt7530: support adjusting EEE")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
5.10.37 and 5.4.119 introduced a lot of DVFS changes for Armada 37xx from 5.13 kernel.
Unfortunately commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/cpufreq/armada-37xx-cpufreq.c?h=v5.10.37&id=a13b110e7c9e0dc2edcc7a19d4255fc88abd83cc
This patch actually corrects the things so that 1 or 1.2GHz models would actually get scaled to their native frequency.
However, due to a AVS setting voltages too low this will cause random crashes on 1.2GHz models.
So, until a new safe for everybody voltage is agreed on
lets revert the patch.
Fixes: d337731 ("kernel: bump 5.10 to 5.10.37")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
|
|
|
|
|
|
|
|
|
|
| |
The previous config will only show 2.4G radio activity status
This change mr24:green:wifi4 and mr24:green:wifi2 to
show 2.4G and 5G radio on and off status
change mr24:green:wifi3 and mr24:green:wifi1 to
show 2.4G and 5G radio activity status
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
|
|
|
|
|
|
| |
Backport a pending patch already reviewed that fix some warning about tsens debugs already registered.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
|
|
|
|
|
|
|
|
|
| |
With some talk with the ARM maintainer, it was notice that enlarging the limit
to the current value is VERY wrong and clash with other memory.
A better solution would be to reduce the IO space from 1MB to 64K as probably
it's a long lasting typo and even x86 arch doesn't have a IO space that big.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
All patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed:
generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Note that since I rebased the previous commit, I removed my Run-tested line
although I confirm building the image successfully.
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed:
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
bcm63xx/patches-5.4/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch*
Removed/code was included upstream and therefore redundant:
ramips/patches-5.4/999-fix-pci-init-mt7620.patch
All other patches automatically rebased.
* update_kernel.sh did not flag this yet it was included in 5.4.119[1], as a
result of the rebase, I removed my testing lines since I did not go back to
test built or to run test 5.4.119 with the removed patch present.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.119&id=e5b3e69eb36ac1178a7a2392616fd29afd288c4e
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased:
ath79/patches-5.4/0033-spi-ath79-drop-pdata-support.patch
Removed uneeded patch:
ath79/patches-5.4/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
| |
Automatically refreshed:
generic/pending-5.10/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Automatically refreshed:
apm821xx/patches-5.10/802-usb-xhci-force-msi-renesas-xhci.patch
generic/backport-5.10/610-v5.13-31-net-ethernet-mtk_eth_soc-fix-parsing-packets-in-GDM.patch
generic/backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch
generic/backport-5.10/610-v5.13-33-net-ethernet-mtk_eth_soc-add-flow-offloading-support.patch
generic/hack-5.10/204-module_strip.patch
generic/hack-5.10/911-kobject_add_broadcast_uevent.patch
ipq806x/patches-5.10/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch
ipq806x/patches-5.10/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch
Deleted (reverse-appliable):
generic/backport-5.10/610-v5.13-37-net-ethernet-mtk_eth_soc-fix-RX-VLAN-offload.patch
ipq806x/patches-5.10/106-5.13-net-stmmac-Set-FIFO-sizes-for-ipq806x.patch
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
| |
This switches device names to the common 'vendor_model' approach as in
most of other targets in OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
| |
- drop unused 'UBOOT' variable from 'Device/apalis' recipe
- fix 'KERNEL_SUFFIX' for 'Device/cubox-i' (should be '-zImage')
- drop redundant 'DEVICE_{VENDOR,MODEL}' from 'Device/ventana-large'
- other, minor fixes
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
| |
Freescale no longer exists, it was acquired by NXP in 2015.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
| |
brcmnand patch was applied upstream on 5.10.37 update.
Fixes: d337731f85c8 ("kernel: bump 5.10 to 5.10.37")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
| |
This reduces redundant instructions.
The solution is inspired by a different implemention of
Roman Kuzmitskii.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b
Specifications:
- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging
Flashing instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.
Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
Use tabs consistently.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
COMFAST CF-E375AC is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
1) Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
2) TFTP
2.1) Set a tftp server on your machine with a fixed IP address of
192.168.1.10. A place the sysupgrade as firmware_auto.bin.
2.2) boot the device with an ethernet connection on fixed ip route
2.3) wait a few seconds and try to login via ssh
3) TFTP trough Bootloader
3.1) open the device case and get a uart connection working
3.2) stop the autoboot process and test connection with serverip
3.3) name the sysupgrade image firmware.bin and run firmware_upg
MAC addresses:
Though the OEM firmware has four adresses in the usual locations,
it appears that the assigned addresses are just incremented in a
different way:
interface address location
LAN: *:DC 0x0
WAN *:DD 0x1002
WLAN 2.4g *:E6 n/a (0x0 + 10)
WLAN 5g *:DE 0x6
unused *:DF 0x5006
The MAC address pointed at the label is the one assign to the LAN
interface.
Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
[add label-mac-device, remove redundant uart status, fix whitespace
issues, fix commit message wrapping, remove x bit on DTS file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Ubiquiti EdgeRouter 6P is 6 port router with similar
specifications as the EdgeRouter 4, support for which was added
in commit dd651e54cc5eadba480a56a7d2c18471e560f491
There are five 10/100/1000 Mbps RJ/Copper ports and
one 1000 Mbps SFP port.
SoC: Octeon Cavium 7130 (Cavium 3) at 1000MHz
Memory: 1GiB DDR3
Flash: 2x2M chips with uboots (chainloaded) + 512K eeprom
LEDs: 1x for power status (white/blue, controllable)
and 6x for ethernet and SFP ports (no control over them)
Buttons: 1x Reset
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1
USB: 1x USB3.0 on front panel
MII: 1x QSGMII from SoC
PHY: 1x Vitesse VSC8504 of which 4 ports are used (phys 4-7)
1x Vitesse VSC8514 of which 2 ports are used (phys 8-9)
Network port mapping
- eth0 on device maps to lan0 and phy5
- eth1 on device maps to lan1 and phy6
- eth2 on device maps to lan2 and phy7
- eth3 on device maps to lan3 and phy8
- eth4 on device maps to lan4 and phy9
- eth5 (SFP) on device maps to lan5 and phy4
What is not working:
- There is no port status available before it goes up
- SFP have no additional status and presented as no different from eth
- Power-over-ethernet (passive) support has not been tested
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to EdgeRouter 6P front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to EdgeRouter 6P
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log
in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console
after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have
edgerouter 6p running openwrt
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash patches, move ethernet@0 to DTS, share image setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
| |
EdgeRouter 4 and upcoming EdgeRouter 6P and 12 have similar setup,
so create a shared DTSI to prevent duplicate code.
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash commits, add description, move ethernet@0 to DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Vendor firmware expects model name without manufacturer name inside
'supported_devices' part of metadata. This allows direct upgrade to
OpenWrt from vendor's GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes a small regression where the lzma-loader variable values
are being shared between boards that require different configurations.
If not set to "" globally, a device without these settings will just take
the last values another device has set before in the queue.
Fixes: 1b8bd17c2d07 ("ath79: lzma-loader: allow setting custom kernel magic")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[add detailed explanation to the commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Automatically refreshed:
ath79/patches-5.10/0032-MIPS-ath79-sanitize-symbols.patch
bcm63xx/patches-5.10/322-MIPS-BCM63XX-switch-to-IRQ_DOMAIN.patch
bcm63xx/patches-5.10/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch
bmips/patches-5.10/001-v5.11-mips-bmips-select-ARCH_HAS_RESET_CONTROLLER.patch
bmips/patches-5.10/041-v5.13-mtd-rawnand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch
bmips/patches-5.10/202-mips-bmips-disable-ARCH_HAS_SYNC_DMA_FOR_CPU_ALL.patch
bmips/patches-5.10/600-mips-bmips-add-pci-support.patch
generic/backport-5.10/103-v5.13-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch
generic/hack-5.10/301-mips_image_cmdline_hack.patch
generic/hack-5.10/402-mtd-blktrans-call-add-disks-after-mtd-device.patch
generic/hack-5.10/902-debloat_proc.patch
generic/pending-5.10/300-mips_expose_boot_raw.patch
generic/pending-5.10/495-mtd-core-add-get_mtd_device_by_node.patch
generic/pending-5.10/630-packet_socket_type.patch
ipq806x/patches-5.10/0072-add-ipq806x-with-no-clocks.patch
ipq806x/patches-5.10/099-1-mtd-nand-raw-qcom_nandc-add-boot_layout_mode-support.patch
lantiq/patches-5.10/0001-MIPS-lantiq-add-pcie-driver.patch
lantiq/patches-5.10/0023-NET-PHY-add-led-support-for-intel-xway.patch
lantiq/patches-5.10/0152-lantiq-VPE.patch
Deleted (reverse-appliable):
bmips/patches-5.10/052-v5.13-gpio-guard-gpiochip_irqchip_add_domain-with-GPIOLIB_.patch
generic/backport-5.10/499-v5.13-mtd-don-t-lock-when-recursively-deleting-partitions.patch
Deleted (alternative upstream fix):
ramips/patches-5.10/330-fix-pci-init-mt7620.patch
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Automatically refreshed:
apm821xx/patches-5.10/802-usb-xhci-force-msi-renesas-xhci.patch
ath79/patches-5.10/410-spi-ath79-Implement-the-spi_mem-interface.patch
bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch
generic/pending-5.10/465-m25p80-mx-disable-software-protection.patch
ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch
ipq806x/patches-5.10/101-dwmac-ipq806x-qsgmii-pcs-all-ch-ctl.patch
ipq806x/patches-5.10/106-5.13-net-stmmac-Set-FIFO-sizes-for-ipq806x.patch
Deleted (empty or reverse-appliable):
ath79/patches-5.10/411-spi-ath79-add-SPI_MASTER_GPIO_SS-flag.patch
ath79/patches-5.10/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch
ath79/patches-5.10/0054-spi-sync-up-initial-chipselect-state.patch
Manually refreshed:
ath79/patches-5.10/0033-spi-ath79-drop-pdata-support.patch
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
|
|
| |
The two device strings were not ordered properly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|