aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* bcm63xx: Add support for D-Link DSL-2750u rev C1Ahmed Naseef2020-12-0513-9/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the D-Link DSL-2750u rev C1. (https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1) It uses the same hardware as ADB P.DG A4001N. CPU: Broadcom BCM63281 (320 MHz) RAM: 32M (Winbond W9725G6JB) Flash: 8M (MXIC MX25L6445E) Ethernet: 4x 100 Mbps Wireless: 802.11b/g/n: BCM43225 USB: 1x 2.0 Flash instructions: 1. Assign static IP 192.168.1.100 to PC 2. Unplug the power source 3. Press the RESET button at the router, don't release it yet! 4. Plug the power source.Wait some seconds 5. Release the RESET button 6. Browse to http://192.168.1.1 7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and wait some minutes until the firmware upgrade finish. Signed-off-by: Ahmed Naseef <naseefkm@gmail.com> [DTS improvements, proper board patch, refresh patches] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: A4001N A-000-1A1-AX: remove PSI (nvram) partitionDaniele Castro2020-12-051-6/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI) is a Telecom Italia braded router and it seems that there are no public available unbranded versions of this router. The stock Telecom Italia braded firmware has many partitions and the partition layout changes with every firmware relase. The PSI nvram partition is present in the stock firmware under the "UNKNOWN" name but it's empty, full of FFs. Since removing partitions does not cause problems with the stock firmware reflashing procedure, I removed from the dts the PSI nvram partition from OpenWrt, expanded the rootfs one and added the NVRAM partition contained in the cfe bootloader. Furthermore this router's flash needs to be entirely reprogrammed and a new generic bcm6328 cfe must be flashed to boot OpenWrt. The same process takes place when reflashing the stock firmware. Here follows the original flash layout for AGPWI_1.1.0_013, the last stock Telecom Italia braded firmware for which we have root credentials (admin/riattizzati). Flash layout: Section 00 Type BOOT Range 0x00000000-0x00020000 MaxSize 0x00020000 No more information. Section 01 Type IMAGE Range 0x00020000-0x007C0000 MaxSize 0x0079FF6C Uninitialized. Section 02 Type IMAGE Range 0x00800000-0x00FA0000 MaxSize 0x0079FF6C Uninitialized. Section 03 Type CONF Range 0x00FA0000-0x00FC0000 MaxSize 0x0001FF6C Size 0x0000841E Name 'rg_conf' Checksum 0x0041E03B Counter 0x0000051F Start Offset 0x00000000 Section 04 Type CONF Range 0x00FC0000-0x00FE0000 MaxSize 0x0001FF6C Size 0x0000838E Name 'rg_conf' Checksum 0x00419A5A Counter 0x00000522 Start Offset 0x00000000 Section 05 Type FACTORY Range 0x00FE0000-0x00FF0000 MaxSize 0x0000FF6C Size 0x00000554 Name 'rg_factory' Checksum 0x0001255E Counter 0x000004D3 Start Offset 0x00000000 Section 06 Type UNKNOWN Range 0x00FF0000-0x01000000 MaxSize 0x00010000 No more information. Total 7 sections found. The last AGPWI firmware relase should be AGPWI_4.0.6 and it has much more partitions than AGPWI_1.1.0_013. The cfe partition in the stock firmware is 0x00020000 bytes long unlike the OpenWrt dts in wich it's 0x00010000 bytes long because from 0x00010000 to 0x00020000 in the stock cfe there are only 00s and also because the cfe must anyway be reflashed with a generic bcm6328 cfe 0x00010000 bytes long to run OpenWrt. Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [Amend commit, remove unneeded cfe_nvram partition] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: support xmit_more in BQLSieng Piaw Liew2020-12-051-0/+54
| | | | | | | | Support bulking hardware TX queue by using xmit_more. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Amend commit description, fix kernel xmit_more exceptions] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add BQL supportSieng Piaw Liew2020-12-051-0/+67
| | | | | | | | Add Byte Queue Limits support to reduce/remove bufferbloat in bcm63xx target. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Amend commit description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: add support for TP-Link TL-WDR7500 v3Adrian Schmutzler2020-12-044-2/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | This ports support for the TP-Link TL-WDR7500 v3 from ar71xx to ath79. The basic features appear to be identical to the Archer C7 v1, however it has the (supported) QCA9880-BR4A chip of the C7 v2. Specifications: SoC: QCA9558 CPU: 720 MHz Flash: 8 MiB RAM: 128 MiB WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac Qualcomm Atheros QCA9880-BR4A Ethernet: 5x Gbit ports USB: 2x 2.0 ports Flashing instructions: Upload the factory image via the OEM firmware GUI. TFTP recovery appears to be available as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.81John Audia2020-12-049-20/+20
| | | | | | | | | | | | | | All modifications made by update_kernel.sh/no human intervention needed Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [another refresh] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: drop redundant status for gpio/gpio0Adrian Schmutzler2020-12-0445-180/+0
| | | | | | | | | | The first gpio controller (gpio or gpio0) is always enabled by default in the SoC DTSI files. No need to set status=okay in the device DTS files a second time. Remove the redundant statements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: drop num-cs for SPI controllerAdrian Schmutzler2020-12-04171-297/+3
| | | | | | | | None of the spi drivers on ath79 uses the num-cs property. Cc: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: remove num-chipselects from SPI controllerAdrian Schmutzler2020-12-049-14/+0
| | | | | | | | | | | | | | The num-chipselects property is only valid for bit-banged spi-gpio [1]. For the generic SPI controller bindings, num-cs would be the correct property [2]. Since num-cs is not required on ath79 either, just drop the lines. [1] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-gpio.yaml [2] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-controller.yaml Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* x86: enable CONFIG_MMC_SDHCI_ACPI for x86_64Mengyang Li2020-12-031-0/+2
| | | | | | | | | | | | | | | | | | | | | Some x86_64 single board computer (including Atomic Pi) has onboard emmc, but requires CONFIG_MMC_SDHCI_ACPI driver to use or boot from it. Here is boot message for the mmc device [ 2.838008] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA [ 2.857536] mmc1: SDHCI controller on ACPI [80860F14:01] using ADMA [ 2.950019] mmc0: new HS200 MMC card at address 0001 [ 3.158271] mmcblk0: mmc0:0001 M52516 14.6 GiB [ 3.170290] mmcblk0boot0: mmc0:0001 M52516 partition 1 4.00 MiB [ 3.177191] mmcblk0boot1: mmc0:0001 M52516 partition 2 4.00 MiB [ 3.183963] mmcblk0rpmb: mmc0:0001 M52516 partition 3 4.00 MiB, \ chardev (248:0) Other lines changed in this config file are introduced by menuconfig. Signed-off-by: Mengyang Li <mayli.he@gmail.com>
* brcm63xx: add USB status LED in 01_leds for ADP P.DG A4001NDaniele Castro2020-12-041-1/+2
| | | | | | Add a status LED in 01_leds for USB 2-1 connected devices. Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
* ath79: remove ar934x MDIO reset from MAC nodeDavid Bauer2020-12-021-2/+2
| | | | | | | | | | | Remove the MDIO reset from the MAC mode for the AR934x SoC family. The reset is currently also defined for the MDIO node, where the reset is acquired exclusively. In case the ethernet node is enabled, this triggers a warning, as the reset is already acquired by the MAC. Signed-off-by: David Bauer <mail@david-bauer.net>
* bcm63xx: enetsw: switch to netdev_alloc_skb_ip_alignSieng Piaw Liew2020-12-021-0/+37
| | | | | | | | | | | | | | | | | | | Increases packet processing performance by 30%. Tested on BCM6328 320 MHz and iperf3 -M 512 for packet/sec performance. Before: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender [ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver After: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 155 MBytes 43.3 Mbits/sec 354 sender [ 4] 0.00-30.00 sec 154 MBytes 43.1 Mbits/sec receiver Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Merge patches, amend commit and add patch description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: batch process RX pathSieng Piaw Liew2020-12-021-0/+53
| | | | | | | | | | | | | | | | | | | Use netif_receive_skb_list to batch process skb in RX. Tested on BCM6328 320 MHz using iperf3 -M 512, increasing performance by 12.5%. Before: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender [ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver After: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 136 MBytes 37.9 Mbits/sec 203 sender [ 4] 0.00-30.00 sec 135 MBytes 37.7 Mbits/sec receiver Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Amend commit description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: enable LNA for all ar9344 TPLink CPE devicesThomas Huehn2020-12-022-16/+16
| | | | | | | | | | | | The TPLink CPE devices CPE210/CPE510 based on ar9344 have a build-in Low Noise Amplifier on both of the 2x2 mimo rx chains. This patch activates those two LNAs in the respective receiving chains and hence improves the RX sensitivity by about 20dB. Tested on CPE510 v2 & v3. Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de> Acked-by: Robert Marko <robimarko@gmail.com>
* realtek: fix SFP ports on the dlink 10port switchJohn Crispin2020-12-022-2/+14
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: add zyxel_gs1900-10hp supportJohn Crispin2020-12-023-0/+296
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: cleanup package selectionJohn Crispin2020-12-022-4/+2
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: clean up board.json generationJohn Crispin2020-12-021-31/+47
| | | | | | | | | | | | In this new setup the switch is treated as wan, lan1.100 is used as our mgmt vlan. The board mac is applied to eth0, switch and switch.1 The board mac is assigned with the LA bit set to all lan ports while incrementing it. Signed-off-by: John Crispin <john@phrozen.org>
* ath79: restore sysupgrade support for ja76pf2 and routerstationsTomasz Maciej Nowak2020-12-014-4/+16
| | | | | | | | | | | | | | | | | | | Because the bug described in FS#2428 has been fixed with bf2870c1d9e1 ("kernel: fix mtd partition erase < parent_erasesize writes") these devices can now safely do sysupgrade. Restore sysupgrade support disabled in: 0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2") cc5256a8bfa0 ("ath79: base-files: disable sysupgrade for routerstations and ja76pf2") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [move Build block, remove check-size argument, wrap sysupgrade line, make commit message easier to read] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: wlr-7100: remove device variant indicatorTomasz Maciej Nowak2020-12-012-2/+1
| | | | | | | As reported by user, the same image works on both device variants which are v1 001 and v1 002. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* tegra: sysupgrade: write additional information to log outputTomasz Maciej Nowak2020-12-011-4/+3
| | | | | | | | This will explain what is actually occuring on dd invocations. Additionally remove comments for steps which are described by printed statements anyway. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* tegra: sysupgrade: use v function for writing logsTomasz Maciej Nowak2020-12-011-6/+6
| | | | | | Sync with x86 target changes. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: sysupgrade: write additional information to log outputTomasz Maciej Nowak2020-12-011-4/+3
| | | | | | | | This will explain what is actually occuring on dd invocations. Additionally remove comments for steps which are described by printed statements anyway. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: sysupgrade: use v function for writing logsTomasz Maciej Nowak2020-12-012-7/+7
| | | | | | Sync with x86 target changes. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* generic: ipeth: fix iOS 14 tetheringDavid Bauer2020-11-301-0/+44
| | | | | | | | This fixes tethering with devices using iOS 14. Prior to this patch, connections to remote endpoints were not possible while data transfers between the OpenWrt device and the iOS endpoints worked fine. Signed-off-by: David Bauer <mail@david-bauer.net>
* lantiq: fix build of squashfs imagesAleksander Jan Bajkowski2020-11-295-5/+5
| | | | | | | | | | | | This patch fixes build of squashfs image on lantiq. Currently the FEATURE variable is overwritten by the subtarget. Fixes: FS#3480 Fixes: f1c652337628 ("lantiq: clean up target/subtarget features") Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> [reformat Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ASUS RT-N56U B1Pavel Chervontsev2020-11-283-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621ST (880 MHz) FLASH: 16 MiB (Macronix MX25L12835FM2I-10G) RAM: 128 MiB (Nanya NT5CB64M16FP-DH) WiFi: MediaTek MT7603EN bgn 2x2:2 WiFi: MediaTek MT7612EN an 2x2:2 BTN: Reset, WPS LED: - Power - WiFi 2.4 GHz - WiFi 5 GHz - WAN - LAN {1-4} - USB {1-2} UART: UART is present as pin hole next to the aluminium capacitor. 3V3 - RX - GND - TX / 115200-8N1 3V3 is the nearest on the aluminium capacitor and nut hole (pin1). USB: 2 ports POWER: 12VDC, 1.5A (Barrel 5.5x2.1) Installation: Via TFTP: Set your computers IP-Address to 192.168.1.75 Power up the Router with the Reset button pressed. Release the Reset button after 5 seconds. Upload OpenWRT sysupgrade image via TFTP: tftp -4 -v -m binary 192.168.1.1 -c put IMAGE MAC addresses: 0x4 *:98 2g/wan, label 0x22 *:9c 0x28 *:98 0x8004 *:9c 5g/lan Though addresses are written to 0x22 and 0x28, it appears that the vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the same here. Signed-off-by: Pavel Chervontsev <cherpash@gmail.com> [add MAC address overview, add label-mac-device, fix IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: fixup Turris Omnia U-Boot environmentKlaus Kudielka2020-11-271-0/+44
| | | | | | | | | | | | | | Fixup dfa357a3de "mvebu: base-files: Update Turris Omnia U-Boot environment" which should have included this file as well. By rebasing the initial patch this file somehow disappeared. Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020") Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia) [explain fixup in commit message] Signed-off-by: Paul Spooren <mail@aparcar.org>
* mvebu: base-files: Update Turris Omnia U-Boot environmentKlaus Kudielka2020-11-261-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move the update procedure from sysupgrade to first boot, which is much more convenient in the sysupgrade case (otherwise the environment is always one generation behind). Check whether we have an old U-Boot release installed, and update the environment only if necessary. Some notes on the U-Boot environment: The first 9 lines are a copy of the default environment of the old U-Boot release - only modified, to run "distro_bootcmd", in case "mmcboot" fails to boot the factory OS. The remaining 16 lines are a backport of the default environment of the new U-Boot release (shipped with CZ11NIC23). The main entry point is "distro_bootcmd", which eventually sources boot.scr. This way, we have a unified boot protocol for all Turris Omnia revisions so far. This commit also fixes a shortcoming of previous Turris Omnia support: Users may install OpenWrt with the Turris Omnia in factory state (i.e. invalid environment store). In that case, neither fw_setenv, nor U-Boot itself, would import the default environment from the image - screwing up the rescue system, at least! Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020") Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
* mvebu: Add turris-omnia.bootscriptKlaus Kudielka2020-11-262-1/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | In contrast to the U-Boot version shipped with older versions of Turris Omnia (CZ11NIC13, CZ11NIC20), the version shipped with Turris Omnia 2019 (CZ11NIC23) relies on the existence of /boot.scr. Consequently, add a suitable boot script to the sysupgrade image. Flash instructions for Turris Omnia 2019: - Download openwrt-...-sysupgrade.img.gz, gunzip it, and copy the resulting .img file to the root of a USB flash drive (FAT32 or ext2/3/4). - Enter a rescue shell: Either via 5-LED reset and ssh root@192.168.1.1 on LAN port 4, or via 7-LED reset and the serial console. - Insert the USB drive and mount it: mkdir /mnt; mount /dev/sda1 /mnt - Flash the OpenWrt image to eMMC: dd if=/mnt/openwrt-...-sysupgrade.img of=/dev/mmcblk0 bs=4096 conv=fsync - Reboot. Flash instructions using a temporary "medkit" installation were written for the older versions of Turris Omnia, and will *not* work on the Turris Omnia 2019. Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
* initramfs: switch to tmpfs to fix ujailDaniel Golle2020-11-271-1/+11
| | | | | | | | | | | | | | | | Hauke wrote: > We want to run some processes in the procd-ujail, this works when we > use a SquashFS image and an overlay file system, but when we use an > initramfs it does not work. > [...] > When we switch from initramfs to tmpfs, it is working, we added this > code to target/linux/generic/other-files/init to make [it] work. Move files to newly mounted tmpfs and then use switch_root to chroot into new rootfs and free initramfs. Suggested-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: clean up patch fuzzKevin Darbyshire-Bryant2020-11-269-30/+18
| | | | | | | Recent kernel bumps & target patch refactors have left some patch fuzz around. Refreshed kernel patches using update_kernel script. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: add GS110TPPV1 support to mtdsplit_uimageJohn Crispin2020-11-261-3/+5
| | | | | | The ID is used be a Realtek based switch made by Netgear. Signed-off-by: John Crispin <john@phrozen.org>
* realtek: update the tree to the latest refactored versionJohn Crispin2020-11-2662-4254/+4570
| | | | | | | | | | | | | | | * rename the target to realtek * add refactored DSA driver * add latest gpio driver * lots of arch cleanups * new irq driver * additional boards Signed-off-by: Bert Vermeulen <bert@biot.com> Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 5.4 to 5.4.80John Audia2020-11-2629-108/+79
| | | | | | | | | | | | | | | | | Removed since could be reverse-applied by quilt and found to be included upstream: backport-5.4/789-net-usb-qmi_wwan-Set-DTR-quirk-for-MR400.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/generic Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64 build/run]
* ramips: mt7621: replace missing custom-initramfs-uimageSander Vanheule2020-11-261-1/+1
| | | | | | | | | | custom-initramfs-uimage was replaced by calls to uImage, but apparently mtc_wr1201 was missed in the transistion. Use uImage for this device too. Fixes: 9f574b1b875c "ramips: mt7621: drop custom uImage function" Signed-off-by: Sander Vanheule <sander@svanheule.net>
* treewide: add space before SPDX identifierAdrian Schmutzler2020-11-255-5/+5
| | | | | | | | | | | | | | | | | | | | | Strictly, an SPDX identifier requires a space between the comment marker and the identifier itself. The choice of the comment marker itself is irrelevant. Correct: // SPDX-License-Identifier: GPL-2.0-or-later OR MIT Wrong: //SPDX-License-Identifier: GPL-2.0-or-later OR MIT Fix that in the whole tree (actually, only ramips contained wrong uses). Found by checkpatch.pl Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Xiaomi Mi Router 4CAtaberk Özen2020-11-254-0/+147
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi's Mi Router 4C device. Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LEDs: 2x yellow/blue. Programmable (labelled as power on case) - Non-programmable (shows WAN activity) - Button: Reset How to install: 1- Use OpenWRTInvasion to gain telnet and ftp access. 2- Push openwrt firmware to /tmp/ using ftp. 3- Connect to router using telnet. (IP: 192.168.31.1 - Username: root - No password) 4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into the router.. 5- It takes around 2 minutes. After that router will restart itself to OpenWrt. Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com> [wrap commit message, bump PKG_RELEASE for uboot-envtools, remove dts-v1 from DTS, fix LED labels] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tegra: sysupgrade: use get_image_dd wrapperTomasz Maciej Nowak2020-11-251-6/+6
| | | | | | | | This function eliminates false-positive errors emitted by dd. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [drop argument check changes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tegra: sysupgrade: remove redundant MBR checkTomasz Maciej Nowak2020-11-251-13/+0
| | | | | | | | This is already done by get_partitions. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [add "redundant" to title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: sysupgrade: use get_image_dd wrapperTomasz Maciej Nowak2020-11-251-6/+6
| | | | | | This function eliminates false-positive errors emitted by dd. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: sysupgrade: remove redundant MBR checkTomasz Maciej Nowak2020-11-251-13/+1
| | | | | | | | This is already done by get_partitions. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [add "redundant" to title, remove declaration of magic variable] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rtl838x: drop custom mkimage build functionSander Vanheule2020-11-251-12/+1
| | | | | | | | UIMAGE_MAGIC is now supported by Build/uImage, in addition to UIMAGE_NAME. This removes the need for a custom mkimage call, so let's remove it. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: netgear: trim down uImage customisationsSander Vanheule2020-11-254-32/+26
| | | | | | | | | | Replace NETGEAR_KERNEL_MAGIC by UIMAGE_MAGIC to better match the variable's purpose. This allows to drop the custom Build/netgear-uImage. Signed-off-by: Sander Vanheule <sander@svanheule.net> [keep UIMAGE_MAGIC definitions even for default value] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: drop custom uImage functionSander Vanheule2020-11-251-21/+10
| | | | | | | | Use the mkimage argument overrides provided by uImage to implement the customisations required for the initramfs, instead of the near-identical custom function. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* mvebu: base-files: move additional files to subtargetsTomasz Maciej Nowak2020-11-252-0/+0
| | | | | | | Both of these scripts are only relevant to cortexa9, therefore move them there. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: sort patchesTomasz Maciej Nowak2020-11-2550-43/+87
| | | | | | | | | | Sort patches according to target/linux/generic/PATCHES. Additionally: - replace hashes in backported patches with the ones from main Linux tree - add descriptions to some patches Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [remove 004-add_sata_disk_activity_trigger.patch separately] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: remove redundant patch for Linksys LED triggerAdrian Schmutzler2020-11-251-39/+0
| | | | | | | | Remove 004-add_sata_disk_activity_trigger.patch, as the trigger is already added in shared dtsi. Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link MR6400 v5Filip Moc2020-11-254-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are: - smaller form factor - different LED GPIOs - different switch connections You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v5.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>