aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.9 to 4.9.159Koen Vandeputte2019-02-226-523/+0
| | | | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 023-1-smsc95xx-Use-skb_cow_head-to-deal-with-cloned-skbs.patch - 023-6-ch9200-use-skb_cow_head-to-deal-with-cloned-skbs.patch - 023-7-kaweth-use-skb_cow_head-to-deal-with-cloned-skbs.patch - 050-usb-dwc2-Remove-unnecessary-kfree.patch - 092-netfilter-nf_tables-fix-mismatch-in-big-endian-syste.patch - 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch Fixes: - CVE-2018-1000026 Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 3.18 to 3.18.135Koen Vandeputte2019-02-221-5/+5
| | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-3819 - CVE-2019-7221 - CVE-2019-7222 Compile-tested on: adm5120 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: fix wmac memory region for qca953xChuanhong Guo2019-02-201-1/+1
| | | | | | | According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h the size of wmac register range for qca953x is only 0x20000. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* gemini: Generate harddisk image for DNS-313Linus Walleij2019-02-203-7/+50
| | | | | | | | | | | | | | | | | | | | | | This makes OpenWrt build an Ext2+Ext4 partitioned image for the D-Link DNS-313 with two blank partitions, a boot partition on /dev/sda3 and a rootfs partition on /dev/sda4. This uses the methods already used in apm821xx including the tricks to convert the generated Ext2 filesystem partition to version 1 so that the firmware bootloader will properly recognize it. We patch a bit around the build files to make sure we get the rootfs size set and that genext2fs is properly built. Tested on the D-Link DNS-313. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [Fixing and tricksing] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ipq40xx: speed up ath10k-caldata extractionChristian Lamparter2019-02-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reading and writing to and from flash storage is slow and currently, the ath10kcal_extract() scripts are even more at an disadvantage because they use a block size of 1 to be able skip. This patch reworks the extraction scripts to be much faster and efficient by reading and writing the calibration data in possibly one big block. before: (Tested on a RT-AC58U, which has SPI-NAND). # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064 12064+0 records in 12064+0 records out real 0m 0.28s user 0m 0.02s sys 0m 0.24s after: # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.01s user 0m 0.00s sys 0m 0.00s Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: kernel: Add missing config optionPawel Dembicki2019-02-193-0/+3
| | | | | | | | | DRM packages break modules compilation for sunxi target, cortexa7 and cortexa8 subtargets. This patch add missing symbol to generic config. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* armvirt: 32: enable CONFIG_ARM_LPAEYousong Zhou2019-02-191-2/+10
| | | | | | | | | | | | | | | | | | | | | | This is required for running armvirt_32 on QEMU 3.0 [1], otherwise the kernel will emit the following complaint and virtio-net-pci devices will fail to be initialized [ 1.124214] OF: PCI: host bridge /pcie@10000000 ranges: [ 1.125093] OF: PCI: IO 0x3eff0000..0x3effffff -> 0x00000000 [ 1.125942] OF: PCI: MEM 0x10000000..0x3efeffff -> 0x10000000 [ 1.126403] OF: PCI: MEM 0x8000000000..0xffffffffff -> 0x8000000000 [ 1.127748] pci-host-generic 4010000000.pcie: can't claim ECAM area [mem 0x10000000-0x1fffffff]: address conflict with /pcie@10000000 [mem 0x10000000-0x3efeffff] [ 1.129752] pci-host-generic: probe of 4010000000.pcie failed with error -16 Running QEMU with "-M virt,highmem=off" is an option, but "highmem" was only introduced as a default on flag since QEMU 2.5.0 and QEMU will fail and quit on encounter of unknown flags [1] Armv7 guest fails to boot with qemu-3.0.0-1, https://bugzilla.redhat.com/show_bug.cgi?id=1633328#c5 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* armvirt: 32: refresh kernel configYousong Zhou2019-02-191-2/+24
| | | | | | | | | | | | | | | | | | | | | | | The diff was genereated by running the following command without actually changing any kernel config options make kernel_menuconfig CONFIG_TARGET=subtarget Here are some initial findings on the change - CONFIG_ARCH_OPTIONAL_KERNEL_RWX is now arch default - CONFIG_ARM_GIC_V3_ITS is selected by CONFIG_ARCH_VIRT - CONFIG_CPU_SPECTRE is select by CONFIG_CPU_V7 - CONFIG_TIMER_OF is now a arch default - CONFIG_TIMER_PROBE is select by CONFIG_TIMER_OF The following options should probably be moved to generic config - CONFIG_MIGRATION is a default on option - CONFIG_TREE_SRCU is a default on option for !PREEMPT && SMP system - CONFIG_RCU_NEED_SEGCBLIST Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kirkwood: add kernel 4.19 supportPaul Wassi2019-02-1715-0/+1525
| | | | | | | | | | | Add patches for 4.19 Drop patch 200-disable-tso, as the packet corruption was fixed in kernel commit 3b89624ab54b9dc2d92fc08ce2670e5f19ad8ec8 Restructure the DTS for Marvell switch in 104-ea3500 and 105-ea4500 to fix DTC warning. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* x86: video: disable buildtin amdgpu DRM driverLucian Cristian2019-02-174-4/+5
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* x86: DRM: add x64 subtarget supportLucian Cristian2019-02-172-4/+117
| | | | | | copy settings from generic subtarget Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* x86: video: disable builtin radeon DRM driverLucian Cristian2019-02-172-2/+2
| | | | | | | builtin driver can't access the /lib/firmware while booting, module driver will be able to read and load the firmware files Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* kernel: disable CONFIG_USB_IMX21_HCD in default for kernel 4.14Yangbo Lu2019-02-173-1/+2
| | | | | | | | | | | CONFIG_USB_IMX21_HCD should be handled in generic config and module package. So moved it into generic config. This also fixed build issue (kernel config question) of layerscape armv8_32b since it also used ARCH_MXC. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: fix: A64 unstable timerOskari Lemmela2019-02-177-0/+660
| | | | | | | | Backport A64 unstable timer patches from linux 5.1 Signed-off-by: Oskari Lemmela <oskari@lemmela.net> [Split the single patch into the two original patches] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: add support for Sinovoip Banana Pi M2 PlusPawel Dembicki2019-02-172-1/+12
| | | | | | | | | | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 1GB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E) Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212) Onboard header: SPI, I2C, GPIO, UART USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG Untested: Audio, Video Not working: Bluetooth Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* x86: image: add test module to bootloaderTomasz Maciej Nowak2019-02-171-2/+2
| | | | | | | | | | | | It was previously added in 546fced, which was part of "intel-microcode: load as early as possible" series. Unfortunately the conditionals added to GRUB config caused error on boot, because on sysupgrade, bootloader is not updated and is left with old features/modules. Since this module is needed for early microcode load and transition to this needs to be done step by step, enable the test module now, so that every newly created image has it already embedded. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* build: remove leftovers from previous x86 commitsTomasz Maciej Nowak2019-02-172-9/+1
| | | | | | | | | | | | | | | | | VBoxManage is not used and the image is created with proper permisions: 0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host dependencies on qemu-utils and VirtualBox Unreachable config symbols: 9e0759e x86: merge all geode based subtargets into one No need to define those symbols since x86_64 is subtarget of x86: 196fb76 x86: make x86_64 a subtarget instead of a standalone target Unreachable config symbols, so remove GRUB_ROOT: 371b382 x86: remove the xen_domu subtarget Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ar71xx: Fix 5 GHz MAC address for Archer C60 v2Adrian Schmutzler2019-02-171-1/+6
| | | | | | | | Looks like C60 v2 needs the MAC address to be calculated manually, while the C60 v1 gets it correctly without manual interference. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: Remove CONFIG_UDF_NLS for kernel 4.19Rosen Penev2019-02-171-1/+0
| | | | | | kernel 4.18 removed the symbol and made NLS implicit. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: bump 4.19 to 4.19.23Koen Vandeputte2019-02-157-15/+15
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.101Koen Vandeputte2019-02-151-1/+1
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-3819 Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3Oever González2019-02-141-1/+1
| | | | | | | | | | | | | This commit fixes the script that sets the MAC address of the LAN switch. The LAN MAC address should be the WAN MAC address plus one. Without this patch the WAN and the LAN interface will use the same MAC address and an error will be generated. With this patch all interfaces will have a different MAC address, consecutive in the following order: WAN, LAN, radio0 and radio1. Signed-off-by: Oever González <notengobattery@gmail.com>
* ipq8064: Enabling sata port ipq8064 based devicesRoman Glova2019-02-141-0/+2
| | | | | | | | | | | | | | | | | | | | | | (original text here: https://patchwork.kernel.org/patch/8686761/) On some SOCs PORTS_IMPL register value is never programmed by the BIOS and left at zero value. Which means that no sata ports are avaiable for software. AHCI driver used to cope up with this by fabricating the port_map if the PORTS_IMPL register is read zero, but recent patch broke this workaround as zero value was valid for nvme disks. This patch adds ports-implemented dt bindings as workaround for this issue in a way that DT can dictate the port_map incase where the SOCs does not program it already. This patch is equal to commits: 67f8425d0ee1 ("ipq8064: dts: force AP148 SATA port mapping") 2e7a2c91019c ("ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi") in the upstream linux kernel. Signed-off-by: Roman Glova <roman_glova@epam.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added upstream commits, reorg' commit message]
* ath79: add support for I-O DATA WN-AC1600DGRINAGAKI Hiroshi2019-02-148-16/+84
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - SoC: Qualcomm Atheros QCA9557 - RAM: 128 MB - Flash: 16 MB - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 5x 10/100/1000 Mbps - Switch: QCA8337N - LED/key: 6x/6x(4x buttons, 1x slide switch) - UART: through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR 2. Connect power cable to WN-AC1600DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Alternative flash instruction using initramfs image: 1. Prepare a computer and TFTP server software with the IP address "192.168.99.8" and renamed OpenWrt initramfs image "uImageWN-AC1600DGR" 2. Connect between WN-AC1600DGR and the computer with UART 3. Connect power cable to WN-AC1600DGR, press "4" on the serial console and enter the U-Boot console 4. execute "tftpboot" command on the console and download initramfs image from the TFTP server 5. execute "bootm" command and boot OpenWrt 6. On initramfs image, download the sysupgrade image to the device and perform sysupgrade with it 7. Wait ~150 seconds to complete flashing This commit also removes unnecessary "qca,no-eeprom" property from the ath10k wifi node. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix qca955x dual pci resource allocationSantiago Piccinini2019-02-141-1/+1
| | | | | | | | Tested with a dual pci QCA9558 board (LibreRouter v1) in three configurations: enabling pcie0 only, pcie1 only and both enabled. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
* ath79: fix qca955x pcie0 memory sizeSantiago Piccinini2019-02-141-1/+1
| | | | | | | | | Datasheet states that both PCI ranges are of 0x2000000 size: 0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Reviewed-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
* ipq40xx: add support for ASUS LyraMarius Genheimer2019-02-1410-6/+652
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: ea6350v3: 4.19: enable pseudo rng supportChristian Lamparter2019-02-141-0/+4
| | | | | | | Robert Marko made a big effort to enable the rng on all ipq40xx for 4.19, so let's continue the quest. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* gemini: Name binary "bootpart.tar.gz"Linus Walleij2019-02-141-2/+2
| | | | | | | | | | This factory binary i supposed to actually be unzipped and untarred by the user as part of the installation process (this NAS boots from harddisk), so name it "bootpart.tar.gz" and not "factory.bin" so it is helpful for users. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: Add missing config option for kernel 4.19Daniel Engberg2019-02-141-0/+1
| | | | | | Add CONFIG_USB_ROLE_SWITCH otherwise Octeon 4.19 fails compile Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* mpc85xx: 4.19: add missing symbolPawel Dembicki2019-02-141-0/+1
| | | | | | | | OCEDO Panda was added in b368373f, but only for 4.14 config. This patch fix 4.19 build for generic and p2020 subtarget. Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
* ramips: change status LED for Buffalo WHR-G300NINAGAKI Hiroshi2019-02-141-6/+5
| | | | | | | | | | | Buffalo WHR-G300N has a LED for power status indication, but it is not connected to the GPIO and cannot be controlled by the kernel. So, WHR-G300N uses "ROUTER" LED as the system status LED instead. This commit changes it to use "DIAG" LED insted of "ROUTER" like WHR-G301N in ath79 target. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: various Netgear R6120 fixesDavid Bauer2019-02-143-12/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls the WAN LED. Renames the LED accordingly in the device-tree. Removes the 5GHz WLAN LED trigger. Adds the correct WAN port LED trigger. ---- Currently, the MAC address for the Netgear R6120 is read from the NVRAM partition. The offset for the MAC address however is not consistent across devices or firmware versions. Switch to using the factory partition like all other Netgear devices do. ---- The LAN ports of the R6120 are labled in reverse on the casing. Adjust LuCI switchport numbering accordingly. ---- The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset is bigger than the partition itself). Fixes poor performance on 2.4 and 5 GHz. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for I-O DATA WN-AC1167GRINAGAKI Hiroshi2019-02-144-0/+258
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification: - SoC : MediaTek MT7620A - RAM : DDR2 64 MB - Flash : SPI-NOR 8MB - WLAN : 2.4/5 GHz, 2T2R - 2.4 GHz: MT7620A (SoC) - 5 GHz : MT7612E - Ethernet: 10/100/1000 Mbps (ext. MT7530) - LED/key : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J2: TX, GND, RX, Vcc from SoC side - 115200n8 Flash instruction using factory image: 1. Boot WN-AC1167GR normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: proper indentation in image/common-tp-link.mkPaul Wassi2019-02-141-1/+1
| | | | | | Add two spaces for proper indentation in image/common-tp-link.mk Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix port order on TL-WR841ND-v7Paul Wassi2019-02-141-3/+3
| | | | | | | | The switch ports are seen one to one on the case. Also remove unneeded secondary port numbers in this case statement. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: change ledtrig on GL.iNet AR150Paul Wassi2019-02-141-1/+1
| | | | | | | | | Change the ledtrig for LAN from netdev to switch. Although eth1 comes out of the device at a single port, this port is a switch-port and therefore the LED must be triggered by that. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rename TP-LINK to TP-LinkPaul Wassi2019-02-146-34/+34
| | | | | | Remove inconsistencies in the vendor's name. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix TL-MR3220-v2 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+5
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rename TL-WR740ND-v4 to TL-WR740N-v4Paul Wassi2019-02-144-7/+7
| | | | | | Give the device the same name it had in ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kernel: bump 4.19 to 4.19.21Koen Vandeputte2019-02-145-79/+13
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0007-ARM-dts-Fix-up-the-D-Link-DIR-685-MTD-partition-info.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.99Koen Vandeputte2019-02-1432-119/+69
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.156Koen Vandeputte2019-02-142-7/+7
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: enable CONFIG_BPF_JIT by defaultTony Ambardar2019-02-113-3/+3
| | | | | | | | | | | | | | | | | | Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels, which should speed up cBPF and eBPF-based packet filtering (tc, iptables) and packet sniffing (libpcap, tcpdump, fwknopd, etc). This has minimal kernel size impact, increasing the size of uImage-lzma (normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32 arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14. With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko) running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT. This change aligns with the notion of OpenWRT as the network go-to swiss army knife for packet handling, especially on CPU-constrained platforms. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: add support for Xiaomi Mi Router 4QDavid Bauer2019-02-113-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9561 RAM: 64M DDR2 FLASH: 16M SPI-NOR ETH: 1x WAN - 2x LAN WiFi: QCA9561 3T3R BTN: 1x Reset - 1x WPS LED: 1x Blue - 1x Red - 1x Yellow UART: TX - GND - RX - VCC (From ethernet port) 115200n8 - 3.3V Installation ------------ 1. Connect to the device via UART. 2. Interrupt the U-Boot on power-on by pressing enter when prompted. 3. Connect you computer to one of the routers LAN ports. Assign yourself the IP 192.168.31.10/24. Copy the OpenWRT initramfs image to a tftp server root directory. Rename the image to 'x4q.bin'. 4. Load the initramfs image to the router by executing following command in U-Boot. The image will boot afterwards. > tftpboot 0x81000000 x4q.bin; bootm 5. SCP the sysupgrade-image into '/tmp'. Remember to assign yourself an IP in 192.168.1.0/24 for this step! 6. Install OpenWRT permanently by executing > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image> Signed-off-by: David Bauer <mail@david-bauer.net>
* gemini: Fix kmod-led-trig-heartbeat typoLinus Walleij2019-02-111-1/+1
| | | | | | | | It's kmod-ledtrig-* not kmod-led-trig-*. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [extended subject] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: add rssileds for xw devicesKoen Vandeputte2019-02-111-0/+1
| | | | | | | | | | | Commit 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication") adds support for using the RSSI strenght via LEDS. The rssileds package addition got lost during altering the patch. Add it again to fix this. Fixes: 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: fold xt_FLOWOFFLOAD fixes into the main patchFelix Fietkau2019-02-093-144/+37
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 23:19:21 +0000