aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add support for Luma Home WRTQ-329ACNTomasz Maciej Nowak2020-09-256-2/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band wireless access point. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 2 MB SPI NOR 128 MB SPI NAND WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 2x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU Buttons: 1x GPIO controlled EEPROM: 16 Kbit, compatible with AT24C16 UART: row of 4 holes marked on PCB as J19, starting count from the side of J19 marking on PCB 1. GND, 2. RX, 3. TX, 4. 3.3V baud: 115200, parity: none, flow control: none The device supports OTA or USB flash drive updates, unfotunately they are signed. Until the signing key is known, the UART access is mandatory for installation. The difficult part is disassembling the casing, there are a lot of latches holding it together. Teardown Prepare three thin, but sturdy, prying tools. Place the device with back of it facing upwards. Start with the wall having a small notch. Insert first tool, until You'll feel resistance and keep it there. Repeat the procedure for neighbouring walls. With applying a pressure, one edge of the back cover should pop up. Now carefully slide one of the tools to free the rest of the latches. There's no need to solder pins to the UART holes, You can use hook clips, but wiring them outside the casing, will ease debuging and recovery if problems occur. Installation 1. Prepare TFTP server with OpenWrt initramfs image. 2. Connect to UART port (don't connect the voltage pin). 3. Connect to LAN port. 4. Power on the device, carefully observe the console output and when asked quickly enter the failsafe mode. 5. Invoke 'mount_root'. 6. After the overlayfs is mounted run: fw_setenv bootdelay 3 This will allow to access U-Boot shell. 7. Reboot the device and when prompted to stop autoboot, hit any key. 8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use 'setenv' to do that, then run following commands: tftpboot 0x84000000 <openwrt_initramfs_image_name> bootm 0x84000000 and wait till OpenWrt boots. 9. In OpenWrt command line run following commands: fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000" fw_setenv bootcmd "run openwrt" 10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it with: ubirmvol /dev/ubi0 -N ubi_rootfs sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name> 11. After flashing, the access point will reboot to OpenWrt, then it's ready for configuration. Reverting to OEM firmware 1. Execute installation guide steps: 1, 2, 3, 7, 8. 2. In OpenWrt command line run following commands: ubirmvol /dev/ubi0 -N rootfs_data ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N kernel ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs ubimkvol /dev/ubi0 -S 34 -N kernel1 ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1 ubimkvol /dev/ubi0 -S 264 -N rootfs_data fw_setenv bootcmd bootipq 3. Reboot. Known issues The LEDs ring doesn't have any dedicated driver or application to control it, the only available option atm is to manipulate it with 'i2cset' command. The default action after applying power to device is spinning blue light. This light will stay active at all time. To disable it install 'i2c-tools' with opkg and run: i2cset -y 2 0x48 3 1 0 0 i The light will stay off until next cold boot. Additional information After completing 5. step from installation guide, one can disable asking for root password on OEM firmware by running: sed -e 's/root:x:/root::/' -i /etc/passwd This is useful for investigating the OEM firmware. One can look at the communication between the stock firmware and the vendor's cloud servers or as a way of making a backup of both flash chips. The root password seems to be constant across all sold devices. This is output of 'led_ctl' from OEM firmware to illustrate possibilities of LEDs ring: Usage: led_ctl [status | upgrade | force_upgrade | version] led_ctl solid COLOR <brightness> led_ctl single COLOR INDEX <brightness 0 - 15> led_ctl spinning COLOR <period 1 - 16 (lower = faster)> led_ctl fill COLOR <period 1 - 16 (lower = faster)> ( default is 5 ) led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128> (default is 34) ( default is 34 ) led_ctl pulsing COLOR COLOR: red, green, blue, yellow, purple, cyan, white Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit, changed ubi volumes for easier integration, slightly reworded commit message, changed ubi volume layout to use standard names all around] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add open-drain support to pinctrl-msmBrian Norris2020-09-251-0/+81
| | | | | | | | | | | | | | Submitted upstream. Shouldn't affect existing devices, but enables new device support. https://lore.kernel.org/linux-gpio/20200703080646.23233-1-computersforpeace@gmail.com/ Currently queued for-next: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=13355ca35cd16f5024655ac06e228b3c199e52a9 Signed-off-by: Brian Norris <computersforpeace@gmail.com> [refresh patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 5.4 to 5.4.67John Audia2020-09-2414-23/+19
| | | | | | | | | | | | | | All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x, lantiq/xrx200 and ath79/generic Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL) No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [add test on lantiq] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7300 v2J. Scott Heppler2020-09-237-0/+69
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Santiago Rodriguez-Papa <contact at rodsan.dev> Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Winbond W632GG6MB-12 (256M DDR3-1600) * Flash: Winbond W29N01HVSINA (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
* target: update SPDX license namesAdrian Schmutzler2020-09-22101-101/+101
| | | | | | | SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to GPL-2.0-or-later. Reflect that in the SPDX license headers. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove DTS from ATH79 target namePaul Spooren2020-09-221-1/+1
| | | | | | | The legacy ar71xx target is removed and multiple targets use DTS now, so there is no need to point that out for ATH79 specifically. Signed-off-by: Paul Spooren <mail@aparcar.org>
* mediatek: mt7622: select bluetooth module instead of firmwareChuanhong Guo2020-09-221-1/+1
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: build btmtkuart as a kernel moduleChuanhong Guo2020-09-222-15/+12
| | | | | | | | bluetooth on mt7622 needs a firmware to start. It can't be built-in or it tries to load firmware before rootfs is mounted, and then fails. build it as a kernel module to fix that. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: mt7623: use bash for generating bootable imagesDavid Woodhouse2020-09-191-1/+1
| | | | | | | | | | | | | | | | | It turns out that 'echo -e' isn't portable; it doesn't work in the dash builtin echo and Ubuntu users are complaining. I can't even get octal (specified by POSIX) to work consistently because those variants of 'echo' which *do* support -e don't seem to interpret octalwithout it. I could switch to /bin/echo but using -e with that isn't actually portable *either* even though it works today. For now just stick with bash, and use its builtin. We may end up using something else entirely; perhaps perl. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: fix missing pause on switch port for Banana Pi R2David Woodhouse2020-09-191-0/+27
| | | | | | This causes rx drops when running iperf. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* ipq806x: fix support of Edgecore ECW5410 supportAdrian Schmutzler2020-09-193-81/+21
| | | | | | | | | | | | | | | | This fixes several stylistic and functional errors of the recently added Edgecore ECW5410: - fix call in 11-ath10k-caldata - use hex notation in 11-ath10k-caldata - remove redundant definitions from DTS that are already in DTSI - use proper sorting in image/Makefile - use DEVICE_VENDOR/DEVICE_MODEL instead of DEVICE_TITLE - use SOC instead of DEVICE_DTS Fixes: 59f0a0fd839e ("ipq806x: add Edgecore ECW5410 support") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.66John Audia2020-09-1920-52/+44
| | | | | | | | | | | | All modifications made by update_kernel.sh/no manual intervention needed Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64 No dmesg regressions, everything appears functional Signed-off-by: John Audia <graysky@archlinux.us> [add run test from PR] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: fix mtd partition erase < parent_erasesize writesJohn Thomson2020-09-194-16/+14
| | | | | | | | | | | | | | | | | | This bug applied where mtd partition end address, or erase start address, was not cleanly divisible by parent mtd erasesize. This error would cause the bits following the end of the partition to the next erasesize block boundary to be erased, and this partition-overflow data to be written to the partition erase address (missing additional partition offset address) of the mtd (top) parent device. Fixes: FS#2428 Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [shorten commit title, add Fixes, fix kernel 4.19 as well] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79/mikrotik: fix soft_config location for SXT 5nRoger Pueyo Centelles2020-09-171-4/+4
| | | | | | | | | | | | | The soft_config partition for these devices lays between 0xe000 and 0xf000 (as correctly detected by the RouterBoard platform driver), before the bootloader2 partition which starts at 0x10000. This commit correctly sorts the partitions, fixing the parsing error. Fixes: FS#3314 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
* lantiq: use uniform "u-boot-env" mtd labelMartin Schiller2020-09-1780-84/+84
| | | | | | | | | | | This is the most popular choice in the linux kernel tree. Within OpenWrt, this change will establish consistency with ath79 and ramips targets. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [extend commit message, include netgear_dm200, update base-files] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: image: add check for fdt_add_r and kernel_addr_r variablesVladimir Vid2020-09-171-0/+8
| | | | | | | | | | | fdt_addr and kernel_addr variables are getting obsolete in the mainline u-boot in favor of fdt_addr_r and kernel_addr_r. By checking if the new variables exist, we can make sure that devices with newer version of u-boot will work while not breaking support for the existing ones. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mediatek: fix hardware flow offloadFelix Fietkau2020-09-172-1/+95
| | | | | | Add support for dealing with DSA ports Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: enable FRITZRepeater 3000 ports on switchDavid Bauer2020-09-172-3/+11
| | | | | | | | | | | | The ethernet ports on the AVM FRITZRepeater 3000 are not separated between LAN and WAN in the stock firmware. OpenWrt currently abstracts port 4 as eth0 and port 5 as eth1, bridging them in the kernel. This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx to bridge them on the switch, avoiding traffic on both ports to pass thru the CPU. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Ubiquiti UniFi AP ProDavid Bauer2020-09-174-0/+188
| | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The device was previously supported on the now removed ar71xx target. SoC Atheros AR9344 WiFi Atheros AR9344 & Atheros AR9280 ETH Atheros AR8327 RAM 128M DDR2 FLASH 16M SPI-NOR Installation ------------ Follow the Ubiquiti TFTP recovery procedure for this device. 1. Hold down the reset button while connecting power for 10 seconds. 2. Transfer the factory image via TFTP to the AP (192.168.1.20) 3. Wait 2 minutes for the AP to write the firmware to flash. The device will automatically reboot to OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: sort entries in lib/upgrade/platform.shAdrian Schmutzler2020-09-171-3/+3
| | | | | | Apply alphabetic sorting like in the other files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove empty default casesAdrian Schmutzler2020-09-177-15/+0
| | | | | | There is no apparent reason to have an empty default case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: sort entries in 02_networkAdrian Schmutzler2020-09-171-5/+5
| | | | | | Apply alphabetic sorting like in the other files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add Edgecore OAP-100 supportJohn Crispin2020-09-178-1/+527
| | | | | | | | | | | | | | | | flashing the unit * first update to latest edcore FW as per the PDF instructions * boot the initramfs - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm * inside the initramfs call the following commiands - ubiattach -p /dev/mtd0 - ubirmvol /dev/ubi0 -n0 - ubirmvol /dev/ubi0 -n1 - ubirmvol /dev/ubi0 -n2 * scp the sysupgrade image to the board and call - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: add Edgecore ECW5211 supportRobert Marko2020-09-177-3/+348
| | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5211 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7 - RAM: 256MB DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB MX35LFxGE4AB SPI-NAND - Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn) - CC2540 BLE connected to USB 2.0 port - Atmel AT97SC3205T I2C TPM Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: add Edgecore ECW5410 supportRobert Marko2020-09-178-1/+447
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: import bootargs-append from IPQ40xxRobert Marko2020-09-171-0/+14
| | | | | | | | | | | | | This imports the patch that adds bootargs-append support from IPQ40xx. This way we can append additional boot arguments from DTS instead of only being able to overwrite them. This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot. But we still need to append console info and ubi root info. This is used by Edgecore ECW5410. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: add GSBI1 node to DTSIRobert Marko2020-09-171-0/+46
| | | | | | | | IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it. Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: 5.4: enable AT803X driverRobert Marko2020-09-171-0/+1
| | | | | | | Its needed for Edgecore ECW5410 which does not use QCA8337 switch, but rather 2x AR8033 PHY-s directly connected to GMAC-s. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* lantiq: remove trailing whitespaces in dtsAleksander Jan Bajkowski2020-09-173-10/+10
| | | | | | Remove trailing whitespaces in dts files. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ath79: fix button types for WZR-HP-AG300H and WZR-600DHPAdrian Schmutzler2020-09-161-0/+3
| | | | | | | | | | Router and Movie "keys" are actually switches for both devices according to the manual. This has been properly implemented in ar71xx, but overlooked when porting to ath79. Fixes: 480bf2827392 ("ath79: add support for Buffalo WZR-HP-AG300H") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Buffalo WZR-600DHPAdrian Schmutzler2020-09-166-267/+294
| | | | | | | | | | | | | | | | | | | | | The hardware of this device seems to be identical to WZR-HP-AG300H. It was already implemented as a clone in ar71xx. Specification: - 680 MHz CPU (Qualcomm Atheros AR7161) - 128 MiB RAM - 32 MiB Flash - WiFi 5 GHz a/n - WiFi 2.4 GHz b/g/n - 5x 1000Base-T Ethernet - 1x USB 2.0 Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.11.1 - Go to “Administration” → “Firmware Upgrade” - Upload the OpenWrt factory image Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use common device definition for Buffalo devicesAdrian Schmutzler2020-09-163-36/+27
| | | | | | | | | | The Buffalo devices in ath79 share their image generation code, so let's create a shared Device definition for them. Since most of them use BUFFALO_HWVER := 3, this is moved as default to the shared definition as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: consistently use "info" label for default-mac partitionAdrian Schmutzler2020-09-1619-56/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The tp-link safeloader devices typically contain a partition "default-mac" which stores the MAC addresses. It is followed by other partitions containing device info, like {"default-mac", 0x610000, 0x00020}, {"pin", 0x610100, 0x00020}, {"product-info", 0x611100, 0x01000}, In DTS, we typically assign a 0x10000 sized partition for these, which is mostly labelled "mac" or "info". In rarer cases, the partitions have been enclosed in a larger "tplink" or "config" partition. However, when comparing different devices, the implementation appears relatively arbitrary at the moment. Thus, this PR aims at harmonizing these partitions by always using the name "info" for the DTS partition containing "default-mac". "info" is preferred over "mac" as we never just have "default-mac" alone, but always some other device-info partitions as well. While at it, this also establishes a similar partitioning for the few devices where the "info" partitions are part of a bigger unspecific "config" partition or similar. Besides the harmonization itself, this also allows to merge a few cases in 11-ath10k-caldata. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rtl838x: fix incorrect assignment from kstrtoul in serial.cAdrian Schmutzler2020-09-161-1/+1
| | | | | | | | Assign return value of kstrtoul to error variable instead of conversion value. Suggested-by: Birger Koblitz <git@birger-koblitz.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rtl838x: refresh configAdrian Schmutzler2020-09-161-11/+15
| | | | | | Use "make kernel_oldconfig" to update and sort target config. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rtl838x: remove some debug output in rtl838x-nor.cAdrian Schmutzler2020-09-161-4/+0
| | | | | | Seems like leftovers from development, remove them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rtl838x: remove and add some empty linesAdrian Schmutzler2020-09-155-1/+4
| | | | | | | Do some minor empty lines cleanup, i.e. remove those at EOF and add some for cosmetic reasons/consistency. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rtl838x: add new architectureBirger Koblitz2020-09-1439-0/+8828
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the RTL838x Architecture. SoCs of this type are used in managed and un-managed Switches and Routers with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash, Ethernet including a DSA switch driver and internal and external PHYs used with these switches. Supported SoCs: RTL8380M RTL8381M RTL8382M The kernel will also boot on the following RTL839x SoCs, however driver support apart from spi-nor is missing: RTL8390 RTL8391 RTL8393 The following PHYs are supported: RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port) RTL8218B internal: internal PHY of the RTL838x chips RTL8318b external (QSGMII 8-port GMAC phy) RTL8382M SerDes for 2 SFP ports Initialization sequences for the PHYs are provided in the form of firmware files. Flash driver supports 3 / 4 byte access DSA switch driver supports VLANs, port isolation, STP and port mirroring. The ALLNET ALL-SG8208M is supported as Proof of Concept: RTL8382M SoC 1 MIPS 4KEc core @ 500MHz 8 Internal PHYs (RTL8218B) 128MB DRAM (Nanya NT5TU128MB) 16MB NOR Flash (MXIC 25L128) 8 GBEthernet ports with one green status LED each (SoC controlled) 1 Power LED (not configurable) 1 SYS LED (configurable) 1 On-Off switch (not configurable) 1 Reset button at the right behind right air-vent (not configurable) 1 Reset button on front panel (configurable) 12V 1A barrel connector 1 serial header with populated standard pin connector and with markings GND TX RX Vcc(3.3V), connection properties: 115200 8N1 To install, upload the sysupgrade image to the OEM webpage. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* kernel: add support for ALLNET devices in mtdsplitBirger Koblitz2020-09-141-0/+50
| | | | | | | Add support for uimage headers from ALLNET and provide support for the SG8208M and SG8310PM devices' magic bytes. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* cns3xxx: drop targetAdrian Schmutzler2020-09-1445-5946/+0
| | | | | | | | | | | | | | | | | | | | | | | | This target has not been updated to 5.4 yet, and the only person trying it (Koen) decided to retreat based on the following reasons: - The target is not DT-aware at all - The huge amount of effort required - The SoC itself reached EoL at Cavium for some time now - Upstream removed some important parts as it's also slowly getting EoL over there - The commercial product that used this will fade out shortly - The amount of download for this binary suggest that the target is not that popular Since nobody has picked up the work since then, and this is the last remaining 4.19-only target, finally drop it now. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: pbr-m1: fix firmware sizeChuanhong Guo2020-09-132-2/+2
| | | | | | | This board is equipped with Winbond W25Q256FV 32M SPI-NOR. Fix partition size for that. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: pbr-m1: increase SPI clock to 50MHzChuanhong Guo2020-09-131-1/+2
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: pbr-m1: add pcie reset for asm1061Chuanhong Guo2020-09-131-0/+12
| | | | | | | | this board has a pcie to sata bridge connected to pcie2 with a separated pcie reset on gpio7. add reset-gpios and corresponding pinctrl nodes into dts. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips/mediatek: improve GRO performance, fix PPE packet parsingFelix Fietkau2020-09-1311-59/+223
| | | | | | | | Backport upstream changes to initialize GDM settings and reset PPE Allow GMAC to recognize the special tag to fix PPE packet parsing Improve GRO performance by passing PPE L4 hash as skb hash Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.4 to 5.4.65John Audia2020-09-124-13/+13
| | | | | | | | | | | All modifications made by update_kernel.sh/no manual intervention needed Build-tested: x86_64 Run-tested: ipq806x (R7800) No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* ath79: support for TP-Link EAP225-Wall v2Sander Vanheule2020-09-124-1/+168
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access point. UART access and debricking require fine soldering. The device was kindly provided for porting by Stijn Segers. Device specifications: * SoC: QCA9561 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR (GD25Q127CSIG) * Wireless 2.4GHz (SoC): b/g/n, 2x2 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO * Ethernet (SoC): 4× 100Mbps * Eth0 (back): 802.3af/at PoE in * Eth1, Eth2 (bottom) * Eth3 (bottom): PoE out (can be toggled by GPIO) * One status LED * Two buttons (both work as failsafe) * LED button, implemented as KEY_BRIGHTNESS_TOGGLE * Reset button Flashing instructions, requires recent firmware (tested on 1.20.0): * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R162 (TXD) and R165 (RXD) Do NOT bridge R164 * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via sysupgrade or LuCI web interface MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From OEM ifconfig: br0 Link encap:Ethernet HWaddr 50:...:04 eth0 Link encap:Ethernet HWaddr 50:...:04 wifi0 Link encap:UNSPEC HWaddr 50-...-04-... wifi1 Link encap:UNSPEC HWaddr 50-...-05-... Signed-off-by: Sander Vanheule <sander@svanheule.net> [fix IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Mercury MW4530R v1Zhong Jianxin2020-09-125-25/+50
| | | | | | | | | | | | | | | | | | | | | Mercury MW4530R is a TP-Link TL-WDR4310 clone. Specification: * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 8192 KiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 Installation: Flash factory image via OEM web interface. Signed-off-by: Zhong Jianxin <azuwis@gmail.com>
* kernel: bump 5.4 to 5.4.64John Audia2020-09-1216-94/+43
| | | | | | | | | | | | | | | | | | | | | | Remove upstreamed patches: generic-backport 701-v5.5-net-core-use-listified-Rx-for-GRO_NORMAL-in-napi_gro.patch Manually merged: mediatek/patches-5.4 0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch All other modifications made by update_kernel.sh Build-tested: ipq806x, lantiq/xrx200, mvebu, x86/64 Run-tested: ipq806x (R7800), mvebu (mamba, rango), lantiq/xrx200 (Easybox 904 xDSL), x86/64 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [add community build/run tests to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: create common DTSI for Sunvalley Filehub devicesAdrian Schmutzler2020-09-123-258/+138
| | | | | | | | | | HooToo HT-TM05 and RAVPower RP-WD03 have almost identical hardware (except for RAM size) and are from the same vendor (SunValley). Create a common DTSI file for them. Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix baud rate for RAVPower RP-WD03Adrian Schmutzler2020-09-121-4/+0
| | | | | | | | | | | | The baud rate for the RAVPower RP-WD03 is 57600, not 115200. Since this is the default from mt7620n.dtsi, the chosen node can simply be removed from the device DTS. Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-08 20:30:58 +0000