aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: add support for TP-Link MR-3040 v2Dmitry Tunin2018-08-164-1/+178
| | | | | | Add support for the ar71xx supported TP-Link MR-3040 v2. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add support for Buffalo WHR-G301NINAGAKI Hiroshi2018-08-165-4/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240. Ported from ar71xx target. Specification: - Atheros AR7240 - 32 MB of RAM - 4 MB of Flash - 2.4 GHz 2T2R wifi - 5x 10/100 Mbps Ethernet - 9x LEDs, 4x keys - LED: 8x gpio-leds, 1x ath9k-leds - key: 2x buttons, 1x slide switch - UART header on PCB - Vcc, GND, TX, RX from LEDs side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WHR-G301N 2. Connect power cable to WHR-G301N and turn on it 3. Access to "http://192.168.11.1/" and open firmware update page ("ファーム更新") 4. Select the OpenWrt factory image and click execute ("実行") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [fix the SUPPORTED_DEVICES to be compatible with the ar71xx image] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add support for upgrade ledMathias Kresin2018-08-1636-0/+44
| | | | | | | | | | Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh script en par with the other implementations using devicetree aliases to define multiple leds for boot status indication. By default, use the boot finished led to indicate an upgrade for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop unused get_status_led functionsMathias Kresin2018-08-162-8/+0
| | | | | | | The function isn't used for targets getting the status leds from the devicetree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix upgrade led handlingMathias Kresin2018-08-164-8/+16
| | | | | | | | | | | | The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: consolidate upgrade state setMathias Kresin2018-08-164-23/+0
| | | | | | | | | | Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: fix bad indentMathias Kresin2018-08-161-7/+6
| | | | | | | Fix the indent to make the make it obvious which condition is the parent of the loop. Signed-off-by: Mathias Kresin <dev@kresin.me>
* cns3xxx: fix mtu setting with kernel 4.14Mathias Kresin2018-08-161-10/+1
| | | | | | | | | | | Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It's necessary to set a max_mtu if a mtu > 1500 is supported. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump kernel 4.9 to version 4.9.120Hauke Mehrtens2018-08-151-65/+0
| | | | | | | | | | | The following patch was integrated upstream: * target/linux/generic/backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch This fixes tries to work around the following security problems: * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump kernel 4.14 to version 4.14.63Hauke Mehrtens2018-08-154-105/+4
| | | | | | | | | | | | The following patches were integrated upstream: * target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch * target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch This fixes tries to work around the following security problems: * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: use both WNDR3x00 power leds for boot status indicationDmitry Tunin2018-08-151-5/+5
| | | | | | | | | | | Use the orange led by default to match the bootloader/stock firmware behaviour. Turn on the green power led after boot to indicate a finished boot and the orange one off. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message, keep orange power led enabled during early kernel boot] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: use both DIR-825 B1 power leds for boot status indicationDmitry Tunin2018-08-151-2/+3
| | | | | | | | | | | Use the orange led by default to match the bootloader/stock firmware behaviour. Turn on the blue power led after boot to indicate a finished boot and the orange one off. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message, keep orange power led enabled during early kernel boot] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for indicating the boot state using multiple ledsDmitry Tunin2018-08-1533-37/+157
| | | | | | | | | | | Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which supports different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A2Cezary Jackiewicz2018-08-157-0/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: enable all ports unconditionallyPawel Dembicki2018-08-151-1/+10
| | | | | | | This patch make all mt7620 ephy ports turned on. It is necessary for some JBOOT devices. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for HiWiFi HC5861Bold-masterDeng Qingfang2018-08-145-1/+155
| | | | | | | | | | | | | | | | | | | | | | | | HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN https://www.hiwifi.com/enjoy-view Specifications: - MediaTek MT7628AN 580MHz - 128 MB DDR2 RAM - 16 MB SPI Flash - 2.4G MT7628AN 802.11bgn 2T2R 300Mbps - 5G MT7612EN 802.11ac 2T2R 867Mbps - 5x 10/100 Mbps Ethernet Flash instruction: 1. Get SSH access to the router 2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one 3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP 4. Run `mtd write /tmp/<filename> firmware` 5. reboot Everything is working Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ath79: add support for TP-Link TL-WR941N/ND v2/v3Chuanhong Guo2018-08-144-0/+184
| | | | | | | | | | | | | Specification: - SoC: Atheros AR9132 - Flash: 4 MB - RAM: 32 MB - Ethernet: Marvell 88E6060 with 5 FE ports. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for TP-Link WR841N/ND v11Johann Neuhauser2018-08-143-1/+42
| | | | | | | | | | | | | | Specification: - SoC: Atheros AR9533 - Flash: 4 MB - RAM: 32 MB - Ethernet: 4x LAN (100M) / 1x WAN (100M) - WiFi: 2.4G 300M Flash instruction: Flash factory image from stock WebUI. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: move TP-Link WR841v9 aliases node from dtsi to dtsJohann Neuhauser2018-08-142-5/+5
| | | | | | | | Move the alias node of the TP-Link WR841v9 and rename the phandle of the qss led to qss_led in preparation for adding the very similar TP-Link WR841v11. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: fix sysupgrade TP-Link WR841v9Johann Neuhauser2018-08-142-2/+1
| | | | | | | Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and for consistency rename everything to tl-wr841-v9. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: Add wifi to WNDR3700, WNDR3700v2 and WNDR3800Hannu Nyman2018-08-144-1/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath9k wifi capabilities to WNDR3700 family. * use kmod-owl-loader to load firmware from "art" * add wifi to DTS * add wifi LEDs Avoid using the same MAC for eth0 LAN and wlan0 by toggling the eth0 MAC into a locally administered MAC. That is currently done by in user-space by adding a uci config item into /etc/config/network (More elegant solution might be setting it already in preinit phase.) Known issues: * wifi firmware file may not get created on the first boot after flashing on time to bring wifi normally up. Likely the overlay jffs2 is not yet ready for creating the firmware file. "wifi up" may still bring wifi up. Wifi will work normally at subsequent boots. * phy0 and phy1 may get assigned mixed, so that phy0 may be the 5GHz radio instead of the normal 2.4GHz, and vice versa for phy1. Does not happen always, but may happen. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [fix the wifi unit address in the dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Pisen WMM003N (Cloud Easy Power)Icenowy Zheng2018-08-143-0/+136
| | | | | | | | | | | | | | | | | | | | | Pisen WMM003N (sold under the name of Cloud Easy Power) is an AR9331-based router and power bank combo device. The device uses a stock firmware modified from OpenWRT for TP-Link TL-WR703N; however some GPIO definition is different on this device with TL-WR703N. An AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also added, and the stock Flash/RAM configuration is 8MiB/64MiB. The stock firmware is an old and heavily modified OpenWRT-based firmware, which has telnetd defaultly open, and the root password is "ifconfig" (quotation marks not included). The factory image format is not known yet, however the stock firmware ships the OpenWRT's sysupgrade command, and it can be used to install a newer firmware. Due to the lack of the access to the STM8 embedded controller, the SD slot is currently not usable (because it's muxed with the on-board USB port) and the AXP PMIC cannot be monitored. Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* ar7: remove linux 3.18 supportKoen Vandeputte2018-08-1314-998/+0
| | | | | | | This target is on 4.9 currently. It seems the support for this old kernel never got dropped. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add missing USB packages into ASL26555-16MZoltan HERPAI2018-08-131-1/+1
| | | | | | | Mirror the package list from the 8M device profile to the 16M device profile. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: drop tl prefix for TP-Link RE450 v2Peter Lundkvist2018-08-132-2/+2
| | | | | | | | This router is called RE450 and the tl prefix was used to identify it as a TP-Link device. Drop the tl prefix since we now have tplink in dts and device name. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* ath79: gmac: add parsers for rxd(v)- and tx(d|en)-delay for AR9344Christian Lamparter2018-08-132-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some AR9344 boards do very poorly with the default settings and need custom rxdv-delay, rxd-delay, txd-delay, txen-delay flags to perform reasonably. In this case the WD My Net Wi-Fi Range Extender can not even manage 10Mbps on a 1Gbit link: root@AR9344:~# iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from client [...] [ 5] local [...] connected to client [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 1.09 MBytes 9.16 Mbits/sec [ 5] 1.00-2.00 sec 895 KBytes 7.33 Mbits/sec [ 5] 2.00-3.00 sec 762 KBytes 6.25 Mbits/sec [...] [ 5] 10.00-10.03 sec 17.0 KBytes 4.74 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.03 sec 9.00 MBytes 7.52 Mbits/sec with but with the correct settings in place, it does much better: root@AR9344:~# iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from client [...] [ 5] local [...] connected to client [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 23.1 MBytes 193 Mbits/sec [ 5] 1.00-2.00 sec 23.1 MBytes 194 Mbits/sec [ 5] 2.00-3.00 sec 23.2 MBytes 195 Mbits/sec [...] [ 5] 10.00-10.04 sec 710 KBytes 180 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.04 sec 237 MBytes 198 Mbits/sec The tx data and enable delay bits definitions are taken from Atheros' AR9344 Data Sheet Section "8.6.1 Ethernet Configuration (ETH_CFG)" on page 153. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add QCA956x GMAC configDavid Bauer2018-08-132-0/+18
| | | | | | This commit adds the ability to configure the GMAC of the QCA956x. Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm47xx: cosmetic fix in model detectionPaul Wassi2018-08-131-1/+1
| | | | | | | | In "brcm47xx: rework model detection" the file 01_detect was moved to 01_network, therefore also update the warning message in case everything fails. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: ar913x: fix eth pll registerChuanhong Guo2018-08-131-1/+1
| | | | | | | PLL for eth0 internal clock on ar913x is at 0x18050014 and AR913X_ETH0_PLL_SHIFT is 20 instead of 17 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: fix speed applied to MII0/1_CTRL on ar71xx/ar913xChuanhong Guo2018-08-131-2/+2
| | | | | | Currently speed value is applied to interface mode field. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add WNDR3700 and WNDR3700v2Hannu Nyman2018-08-134-0/+93
| | | | | | | | | | | | Add support for WNDR3700 and WNDR3700v2. They share most things with WNDR3800. Only device IDs and partition structure needs to be set. Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has also the NA version of the factory image. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: create WNDR3700 series .dtsi and adjust WNDR3800Hannu Nyman2018-08-133-200/+212
| | | | | | | | | | | | | | | | | Prepare for addition of WNDR3700 and WNDR3700v2 by separating the common parts into wndr3700.dtsi and leaving just the device-specific things into wndr3800.dts The three routers are identical except * device IDs * WNDR3700 (v1) has only 8 MB flash, while others have 16 MB. Partition structure needs to be defined for each device. * (WNDR3800 has 128 MB RAM, but RAM size is not in DTS) Also separate the common parts of the image recipe. (Drop also the initramfs recipe.) Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ramips: fix BR-6478ACv2 supportDaniel Gimpelevich2018-08-136-70/+61
| | | | | | | | | | | | | | | | | The wholesale changes introduced in commit f9b8328 missed this DTS file because it hadn't been merged yet. This patch brings it in line to match the other mt7620a devices' DTS files. Additionally, the Internet LED is now labeled correctly and set to unused by default, since the WAN interface is not known in every configuration. Using sysupgrade between images before and after this commit will require the -F flag. Tested-by: Rohan Murch <rohan.murch@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [drop internet led default setting] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Netgear R6120Ludwig Thomeczek2018-08-135-0/+180
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6120, aka Netgear AC1200. Specification: - SoC: MediaTek MT7628 (580 MHz) - Flash: 16 MiB - RAM: 64 MiB - Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E) - LAN speed: 10/100 - LAN ports: 4 - WAN speed: 10/100 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 To flash use nmrpflash with the provided factory.img. Flashing via webinterface will not work, for now. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* at91: do not build image for at91-q5xr5Hauke Mehrtens2018-08-121-1/+1
| | | | | | | | The kernel image of the at91-q5xr5 is getting too bing now and this is breaking the build. Remove the image for the at91-q5xr5 from the build to at least build images for the other devices. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: fix eth pll for ar913xChuanhong Guo2018-08-111-1/+1
| | | | | | PLL node is missing syscon in compatible string. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for I-O DATA WN-AC1600DGR2INAGAKI Hiroshi2018-08-116-9/+252
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM - 16 MB of Flash - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR2 2. Connect power cable to WN-AC1600DGR2 and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support of D-Link DIR-825 B1Dmitry Tunin2018-08-114-0/+288
| | | | | | Add support for the ar71xx supported D-Link DIR-825 B1 to ath79. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add ath9k calibration data MAC addresses patchingChristian Lamparter2018-08-111-0/+50
| | | | | | | | | | | | | | | | | | This patch copies over the MAC patching helper functions from lantiq's target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom file. Not all vendors bothered to write the correct MAC addresses for the ath9k wifi into the calibration data. And while ath9k does have some special dt-properties to extract the addresses from a fixed position, there are still devices that require userspace to edit or modify the caldata. In my case, the MAC address for the Wi-Fi device is stored in an unsorted key-value based "nvram" database and there's an existing userspace tool to extract the data. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for TP-Link TL-WDR4900 v2Chuanhong Guo2018-08-114-2/+245
| | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 8 MB - RAM: 128 MB - Ethernet: AR8327N with 5 GE ports. - Wireless radio: QCA9558 for 2.4G and AR9580 for 5G. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: bump 4.14 to 4.14.62Koen Vandeputte2018-08-104-21/+8
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.119Koen Vandeputte2018-08-104-95/+13
| | | | | | | | | | | | Refreshed all patches. Delete upstreamed patch: - 100-tcp-add-tcp_ooo_try_coalesce-helper.patch Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for OCEDO KoalaDavid Bauer2018-08-094-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: remove PHY resetChuanhong Guo2018-08-096-22/+6
| | | | | | | | | | | | Bit 8/12 of reset controller which is marked as PHY_RESET/SWITCH_RESET in datasheets will trigger either a reset for builtin switch or assert an external ETH0_RESET_L/ETH1_RESET_L pin, which are usually connected to external PHY/switch. None of them should be triggered every time an interface is brought up in ethernet driver. Remove PHY reset support from ag71xx and definition for them in dtsi. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-08-096-9/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros QCA9558. Ported from ar71xx target. Specification: - Qualcomm Atheros QCA9558 - 64 MB of RAM - 16 MB of Flash - 5x 10/100/1000 Ethernet - QCA8337N - 4x LEDs, 2x keys - UART header on PCB - Vcc, TX, RX, GND from LED side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Connect power cable to BHR-4GRV2 and turn on it 3. Access to "http://192.168.12.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新実行") button 5. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix PLL settings for QCA955xDavid Bauer2018-08-093-2/+10
| | | | | | | | | | | | | | This adds PLL settings for the ethernet ports of the TP-Link TL-WR1043 v2/v3 and the Openmesh OM5P-AC-v2. We also change the PLL-settings in the qca9557.dtsi to match the ones used as default on the ar71xx target. As of 4b9680f138 those devices have broken ethernet ports as the default PLL settings defined in the QCA9557.dtsi are applied which are off for those devices. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add pll for archer c7Kevin Darbyshire-Bryant2018-08-091-0/+2
| | | | | | | | | | | | | | | | | | commit 4b9680f fixed pll settings and the correct pll set by bootloader is overrided by value in qca9557.dtsi which is incorrect for Archer C7 and breaks ethernet. Add pll values for archer c7 to fix ethernet connection. This individual pll tweak has been cherry picked from github pr 1260 which changes a couple of things in a single commit and should be ideally split. This commit get archer v7 back and working. Tested: archer c7 v2 Original combined commit authored by: Signed-off-by: Chuanhong Guo <gch981213@gmail.com> c7 fix only split out by: Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* sunxi: change Orange Pi PC2 MUSB/power buttonAntonio Silverio2018-08-091-0/+20
| | | | | | | Changed default role of Orange Pi PC2 MSUB port to host (in dts) Changed default function of Orange Pi PC2 power button to PWR_BTN Signed-off-by: Antonio Silverio <menion@gmail.com>
* sunxi: Added support for Xunlong Orange Pi PC2Antonio Silverio2018-08-091-0/+10
| | | | | | | | | | | | | | | | CPU: H5 High Performance Quad-core 64-bit Cortex-A53 GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL Memory: 1GB DDR3 (shared with GPU) Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB) Onboard Network: 1000M/100M Ethernet RJ45 USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode role by default in DTS Buttons: Power Button(SW4) Debug TTL UART: ..DC-IN.. >[GND][RX][TX] ..HDMI.. Signed-off-by: Antonio Silverio <menion@gmail.com>
* kernel: move e1000e patches to backportsStijn Tintel2018-08-094-0/+0
| | | | | | They're already in linux.git, so they shouldn't be in pending. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 18:09:42 +0000