aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ramips: adding DWM-158 3g ModemGiuseppe Lippolis2016-12-141-0/+14
| | | | | | | | | This patch add the 3G modem DWM-158 to the usb-serial option driver. The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem supportet by lede. The patch has been submitted and merged in the upstream linux-next repository. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ar71xx: Add support for Netgear WNR2000v1Huan Truong2016-12-144-44/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the WNR2000v1 board with 4MB flash, and produces device-specific factory, rootfs, and sysupgrade files for the WNR2000v1. This board is errorneously claimed as supported on the OpenWRT wiki as AP81, but AP81 image would not work because of APT81 image requiring having 8MB of flash, while WNR2000v1 has only 4MB. The image requires the u-boot bootloader to be modified to fuhry's bootloader first. Short specification: - CPU: Atheros AR9132 - 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps - 4 MB of Flash - 32 MB of RAM - UART header (J1) on board - 1x button Factory/Initial flash instructions: - Set up a TFTP server on your local machine. - Download the uImage for ar71xx-generic and the rootfs image for ar71xx-generic-wnr2000 and save in the tftp server root. - Gain serial access to the router via the UART port (telnetenable over the network only won't work!). - Upgrade the u-boot bootloader to fuhry's version by running the script: http://fuhry.com/b/wnr2000/install-repart.sh - When the router restarts, interrupt u-boot and gain access to u-boot command line. - Repartititon the board and flash initial uImage and rootfs as follow. Commands to type in u-boot: # tells u-boot that we have a tftp server on 192.168.1.10 setenv serverip 192.168.1.10 # tells u-boot that the router should take the address 192.168.1.1 setenv ipaddr 192.168.1.1 # erase the region from 0x050000-0x3f0000 erase 0xbf050000 +0x3A0000 # loads sqfs.bin on TFTP server, and put it to memory address 0x81000000 tftpboot 0x81000000 sqfs.bin # it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ # copy bit by bit 0xZZZZZZ bytes from offset 0x050000 cp.b 0x81000000 0xbf050000 0xZZZZZZ # same to the uImage.bin, write it right next to sqfs.bin # again, 0xYYYYYY is the length that tftpboot reports tftpboot 0x81000000 uImage.bin cp.b 0x81000000 0xbf2a0000 0xYYYYYY # We need to tell the kernel what board it is booting into, and where to find the partitions setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd" # Tell u-boot where to find the uImage setenv bootcmd "bootm 0xbf2a0000" # Tell u-boot to save parameters to the u-boot-env partitions saveenv # Reset the board reset Tested on: - WNR2000v1 board. - Initial flash works. Known bugs: - I don't know why factory image doesn't work on initial flash on stock firmware in u-boot recovery mode while it should. - Sysupgrade does not yet work, if you do -f it will mess up your installation (requiring a reinstall of sqfs and uImage). Signed-off-by: Huan Truong <htruong@tnhh.net>
* ar71xx: Add ath10k-firmware-qca988x for DomyWifi DW33DJing Lin2016-12-141-1/+1
| | | | | | | The default package selection was missing the correct FW for ath10k to work. Signed-off-by: Jing Lin <mumuqz@163.com>
* netfilter: drop proprietary xt_id matchJo-Philipp Wich2016-12-143-285/+0
| | | | | | | | The xt_id match was used by the firewall3 package to track its own rules but the approach has been changed to use xt_comment instead now, so we can drop this nonstandard extension. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: backport ubifs support for dirty_writeback_intervalRafał Miłecki2016-12-132-0/+148
| | | | | | | These patches were queued for 4.10. For possible use cases see added: [PATCH] ubifs: Use dirty_writeback_interval value for wbuf timer Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport missed BCM53573 ILP patch from 4.10Rafał Miłecki2016-12-133-13/+39
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump to 4.4.38Kevin Darbyshire-Bryant2016-12-136-17/+17
| | | | | | | | Bump & refresh patches for all 4.4 supported targets. Compile & run tested: ar71xx - Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* bcm53xx: backport DTS patches accepted for 4.11Rafał Miłecki2016-12-138-160/+502
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: simplify model detection for TP-Link Pharos devicesMatthias Schiffer2016-12-121-19/+2
| | | | | | | This also makes the detection more flexible, as it doesn't need to check for each model explicitly. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: remove obsolete flash chip locking codeFelix Fietkau2016-12-125-52/+11
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove PB92 reference design board supportFelix Fietkau2016-12-1210-89/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP113 reference design board supportFelix Fietkau2016-12-1212-106/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP81 reference design board supportFelix Fietkau2016-12-1219-122/+10
| | | | | | This board is very old and unlikely to still be relevant today. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove obsolete duplicate driver source fileFelix Fietkau2016-12-121-294/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP83 reference design board supportFelix Fietkau2016-12-1218-661/+2
| | | | | | | | This board is very old and unlikely to still be relevant today. Support for it contains a significant amount of device specific baggage which is worth getting rid of. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: clean up spi controller related patchesFelix Fietkau2016-12-1223-667/+202
| | | | | | Remove various hacks for fast read, un-break device tree support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm53xx: disable CONFIG_FW_LOADER_USER_HELPER_FALLBACKRafał Miłecki2016-12-121-0/+1
| | | | | | | | | | | There are many targets using user space scripts to generate firmware but bcm53xx doesn't need this, so let's disable that kernel option. This lets us avoid some scary-looking kernel warnings like: brcmfmac 0001:04:00.0: Falling back to user helper firmware brcm!brcmfmac43602-pcie.txt: firmware_loading_store: map pages failed Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* lantiq: remove "init" kernel command line parameter from bootargsMartin Blumenstingl2016-12-1234-125/+2
| | | | | | | | | | /etc/preinit has been the default init-script for a very long time (at least since Linux 2.6.30 in OpenWrt). Remove the kernel command line "init" parameter to get rid of duplicate and inconsistent definitions of this parameter (some boards, like FRITZ3370 for example did not use it at all, while it's just copy and paste on others). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: specify console using stdout-path instead of cmdline argumentMartin Blumenstingl2016-12-1240-37/+70
| | | | | | | | Use devicetree's /chosen/stdout-path instead of the kernel command line (embedded in the .dts-files) to specify the serial console. Using the chosen node is recommended on devicetree based platforms. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ar71xx: add support for YunCore SR3200 and XD3200Piotr Dymacz2016-12-1212-4/+256
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* layerscape: add 64b/32b target for ls1046ardb deviceYutang Jiang2016-12-1216-0/+2547
| | | | | | | | | | | | | | | | | | | | | | | | | | Add support for NXP layerscape ls1046ardb 64b/32b Dev board. LS1046ARDB Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 512 Mbyte NAND flash * Two 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card * On-board 4G eMMC Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: * PCIe1 (SerDes2 Lane0) to miniPCIe slot * PCIe2 (SerDes2 Lane1) to x2 PCIe slot * PCIe3 (SerDes2 Lane2) to x4 PCIe slot * USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port * UART: supports two UARTs up to 115200 bps for console Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
* lantiq: falcon: remove bootargs-appendHauke Mehrtens2016-12-1010-40/+0
| | | | | | | This attribute is not evaluated any more and the boot loader on these reference boards does not provide a broken root= or console= parameter. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: simplify ath9k eeprom extraction scriptMathias Kresin2016-12-081-11/+16
| | | | | | | | | | | Add an extra function to patch the mac and fixup the checksum afterwards. Calculate the checksum position automatically. The offset to the mac address is the same for all checksum protected EEPROMs. No EEPROM requires a byte swapped mac address. The mac byte swap code was required due to an bug in the script that is now fixed. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix ath9k EEPROM data swapping for some devicesMartin Blumenstingl2016-12-081-14/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EEPROM data in the flash of the ARV7518PW, ARV8539PW22, BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning that for example the ath9k base_eep_header fields "version" (high and low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are just 1 byte wide, thus their position is swapped). The old "ath,eep-endian" property enabled the corresponding swapping logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is based on the magic bytes in the EEPROM data which have nothing to do with the calibration data - thus this logic should not be used anymore). Since we have switched to the upstream ath9k devicetree bindings there is no binding anymore which enables swab16 in ath9k (as this logic is not recommended anymore as explained above), leading to ath9k initialization errors: ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0 (this shows that the version field is swapped, expected values are VER 0x000E and REV 0x0001) Swapping the ath9k calibration data when extracting it from the flash fixes the devices listed above (all other devices do not require additional swapping, since the position of the fields is already as expected by ath9k). This allows ath9k to read the version correctly again, as well as the more important "eepmisc" field (which is used for determining whether the data inside the EEPROM is Big or Little Endian which is required to parse the EEPROM contents correctly). Fixes: a20616863d3 ("lantiq: use ath9k device tree bindings binding/owl-loader") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* bcm53xx: update patch adding fake USB doorbellRafał Miłecki2016-12-071-26/+8
| | | | | | | Rob suggested I should use of_machine_is_compatible insteak of a new property and updated patch has been sent. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport LED patch which will allow better DT integrationRafał Miłecki2016-12-061-0/+53
| | | | | | | It's not used by any driver yet, it may just simplify development and testing new features. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: fix potential crash in usbport LED trigger driverRafał Miłecki2016-12-062-0/+70
| | | | | | This backports upstream accepted fix. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3Matthias Schiffer2016-12-064-3/+9
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: Fix led init script for Lenovo Y1/Y1sBangLang Huang2016-12-041-3/+10
| | | | | | | This commit fix the led init script for Lenovo Y1 and Y1S due to the manual and dts file. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* brcm2708: update linux 4.4 patches to latest versionÁlvaro Fernández Rojas2016-12-04531-480/+6619
| | | | | | | As usual these patches were extracted and rebased from the raspberry pi repo: https://github.com/raspberrypi/linux/tree/rpi-4.4.y Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: bump to 4.4.36Álvaro Fernández Rojas2016-12-043-21/+26
| | | | | | | Refresh patches on all 4.4 supported platforms. Compile & run tested: brcm2708/bcm2710 - Raspberry Pi 3 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* orion: make image size errors non-fatalFelix Fietkau2016-12-041-8/+4
| | | | | | Fixes build errors on the generic subtarget Signed-off-by: Felix Fietkau <nbd@nbd.name>
* orion: Enable CONFIG_MV_XORFlorian Fainelli2016-12-041-0/+2
| | | | | | | This is helpful for Orion-based NAS boxes that have the XOR engine enabled since it provides faster software RAID. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Add uboot-envtools in the default package listFlorian Fainelli2016-12-041-1/+2
| | | | | | Makes sense since most, if not all orion platforms use this bootloader. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* kernel: Add missing kernel config symbolFlorian Fainelli2016-12-041-0/+1
| | | | | | Add CONFIG_DW_DMAC_PCI Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Set appropriate DEVICE_TYPE for harddisk targetFlorian Fainelli2016-12-041-0/+1
| | | | | | | The harddisk target is for NAS boxes, so set the DEVICE_TYPE accordingly so we get a sensible default package selection. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Switch to kernel 4.4Florian Fainelli2016-12-041-1/+1
| | | | Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Advertise support for RTCFlorian Fainelli2016-12-041-1/+1
| | | | | | | Otherwise, we can't select RTC_SUPPORT and the corresponding kmod-rtc-* packages. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Make sub-targets augment FEATURES, not re-define itFlorian Fainelli2016-12-042-2/+2
| | | | Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Build images for Buffalo Terastation Pro II/LiveFlorian Fainelli2016-12-042-1/+12
| | | | | | | Enable support for this machine in the kernel and also produce valid image files with the correct machine id. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Add support for 4.4 kernelFlorian Fainelli2016-12-045-0/+1124
| | | | | | Patches and configuration apply just fine on the Marvell Orion target. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* orion: Fold DT2 setup files into patchFlorian Fainelli2016-12-043-536/+553
| | | | Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* kernel: Add check to of_scan_flat_dt() before accessing initial_boot_paramsFelix Fietkau2016-12-041-0/+30
| | | | | | | Fixes a bug that affects rt288x Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: Fix alloc_node_mem_map with ARCH_PFN_OFFSETFelix Fietkau2016-12-041-0/+86
| | | | | | | Fixes a bug that affects rt288x Signed-off-by: Tobias Wolf <github-NTEO@vplace.de> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: set GPIO reset line for Ubiquiti NanoStation Loco XWFelix Fietkau2016-12-041-0/+17
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for configuring at803x PHY GPIO reset via platform dataFelix Fietkau2016-12-041-0/+68
| | | | | | | Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW, because ar71xx is not converted to device tree yet. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add support for the AT8032 PHYFelix Fietkau2016-12-041-0/+65
| | | | | | This PHY is used on the Ubiquiti Networks NanoStation Loco XW Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport some upstream at803x fixesFelix Fietkau2016-12-043-0/+162
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: prevent packet forwarding on mt7620 between switch ports during init ↵Felix Fietkau2016-12-042-5/+7
| | | | | | | | | | | | | | | | (FS#103) By default, forwarding between all ports is allowed on init. This is problematic in cases where some ports are supposed to be isolated from each other, most commonly LAN/WAN separation. REG_ESW_PORT_PCR(port) has a destination mask for a particular port, controlling what other ports it is allowed to send packets to. Instead of initializing all to 0xff (all ports), allow each physical port to send to the CPU port, and the CPU port to send to all other ports. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix LAN port order of WeVO W2914NS v2Yong-hyu, Ban2016-12-041-1/+4
| | | | Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 13:23:50 +0000