aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* ipq40xx: abort ar40xx probe on missing PHYsDavid Bauer2019-09-252-0/+46
| | | | | | | | | | | | The ar40xx driver currently panics in case no QCA807x PHY has been successfully probed. This happens when the external PHY is still in reset when probing the ar40xx switch driver. Note that this patch does not fix the root cause, ar40xx_probe now simply fails instead of causing a kernel panic due to a nullpointer dereference. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: fix issues with output routing in flow offloadFelix Fietkau2019-09-2511-279/+92
| | | | | | | | Replace an old cleanup patch that never made it upstream with the proper upstream fix. This patch was incompatible with the recent changes that affected the way that the flow tuple dst entry was used. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: port 4.19 xt_FLOWOFFLOAD changes to 4.14Felix Fietkau2019-09-253-20/+117
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: port another missing upstream change to xt_FLOWOFFLOAD on 4.19Felix Fietkau2019-09-251-4/+8
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* layerscape: split up DEVICE_TITLE definitionsMoritz Warning2019-09-252-13/+35
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* gemini: dir685: Restore graphicsLinus Walleij2019-09-252-14/+6
| | | | | | | | | | | | | | | One of the v4.19 patches had a bug, this is fixed upstream, but in OpenWrt we can fix it by just fixing the bug in the patch. We also need to augment the config file to select the CONFIG_DRM_FBDEV_EMULATION symbol. This restores the display controller on the DIR-685 to working state: penguin and graphics on the little screen with default OpenWrt install. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* kernel: update and fix xt_FLOWOFFLOAD target on 4.19Felix Fietkau2019-09-251-13/+25
| | | | | | | Merge upstream changes to nft_flow_offload. Fixes offloading Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: initialize youhua, wr1200js WAN MAC addresses from flashAdrian Schmutzler2019-09-251-0/+1
| | | | | | | | | This patch changes wan MAC address setup for youhua,wr1200js from retrieving it by calculation to reading it from flash. This has been checked on-device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WNPR2600GINAGAKI Hiroshi2019-09-253-0/+183
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WNPR2600G is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7615 - 5 GHz : MediaTek MT7615 - Ethernet : 10/100/1000 Mbps - Switch : MT7530 (SoC) - LED/keys : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from SoC side - 57600n8 Flash instruction using factory image: 1. Boot WNPR2600G normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: move "elx-header" to Makefile from mt7620.mk and mt7621.mkINAGAKI Hiroshi2019-09-253-38/+20
| | | | | | | | | | | I-O DATA WNPR2600G has an "elx-header", so move this definition to generic makefile to use it from mt7621 subtarget. This definition is also added to mt7621.mk in f285e8634c57d28aa970b80c5c59e85485f35c7d, so remove it from mt7621.mk. And added a line to cleanup used header file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: replace MAC address configuration for I-O DATA WN-AC-GR devicesINAGAKI Hiroshi2019-09-251-1/+1
| | | | | | | | | | | | | following I-O DATA devices have a MAC address as "wanaddr" for WAN interface in u-boot-env: - WN-AC1167GR - WN-AC733GR3 I replaced MAC address configuration in these devices to omit address calculation in 02_network. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for ipTIME A3Sungbo Eo2019-09-255-92/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek MT7628AN. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 3x 10/100Mbps - Switch: SoC internal - UART: - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for XiaoYu XY-C5Qi Jiang2019-09-253-0/+114
| | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621A Flash: 32 MiB RAM: 512 MiB Ethernet: built-in switch USB: 1x USB3.0 SATA: ASM1060, 1 SATA port Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.173.22 2. Download *-sysupgrade.bin image and rename it to firmware.img 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Turn on router,press the reset button and wait ~15 seconds 6. Release the reset button and after a short time the firmware should be transferred from the tftp server 7. Wait ~3 minutes to complete recovery. Signed-off-by: Qi Jiang <rushx@live.cn> [squash commits, add label-mac-device, fix sign-off style] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: bump 4.19 to 4.19.75Koen Vandeputte2019-09-244-5/+5
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.146Koen Vandeputte2019-09-241-1/+1
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.194Koen Vandeputte2019-09-246-10/+10
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: none Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: convert devices to interrupt-driven gpio-keysAdrian Schmutzler2019-09-2247-94/+51
| | | | | | | | | | | | | This converts all remaining devices to use interrupt-driven gpio-keys compatible instead of gpio-keys-polled. The poll-interval is removed. Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as this one is using ath9k keys. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Karl Palsson <karlp@etactica.com> Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
* apm821xx: remove unnecessary kernel paddingRussell Senior2019-09-211-2/+1
| | | | | | | | | | | | | | | | | | The allocation of LEBs to ubi volumes is handled by the sysupgrade script: package/base-files/files/lib/upgrade/nand.sh and the ubimkvol and or ubirsvol command. Therefore, padding of the kernel blob is not needed at all, so use cat instead of dd. The BLOCKSIZE variable was only used in the dd command. In any case, 63k made no sense for the way BLOCKSIZE was being used. 63k (64512) does make sense for DTB_SIZE because of the offsets expected by u-boot given extant u-boot-env variables. Tested on Meraki MR24. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: add support of Netgear WNDR3800CHDmitry Tunin2019-09-214-3/+53
| | | | | | | | Add support for the ar71xx supported Netgear WNDR3800CH to ath79. The device is identical to WNDR3800 except NETGEAR_BOARD_ID. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: DIR825B1 switch to gpio-keysDmitry Tunin2019-09-211-4/+1
| | | | Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ipq40xx: fix hw-crypto detection of qce driverEneas U de Queiroz2019-09-212-0/+62
| | | | | | | | | | This adds the CRYPTO_ALG_KERN_DRIVER_ONLY flag to Qualcomm crypto engine driver algorithms, so that openssl devcrypto can recognize them as hardware-accelerated. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> [refresh, move to ipq40xx as its the only target right now] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: remove invalid uses of ath9k_patch_fw_mac_crcAdrian Schmutzler2019-09-211-3/+3
| | | | | | | | | | | | Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which is meant to generate a checksum, for fixing their ath9k MAC addresses. However, those do not have a checksum field, and the calculated checksum offset would be negative. This patch will use ath9k_patch_fw_mac function for those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: replace backticks by $(...)Adrian Schmutzler2019-09-212-4/+4
| | | | | | | | | This replaces deprecated backticks by more versatile $(...) syntax. While at it, remove some useless cat commands and deprecated egrep commands. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: image: pad kernel for Adtran/Bluesocket devicesTomasz Maciej Nowak2019-09-211-2/+2
| | | | | | | | | | | | | | | | It has been reported that using the sysupgrade-tar image will trigger "lzma_decode failed error". The RedBoot bootloader always loads data from flash till block size boundary, so if there's no padding it'll also load the beginning of rootfs, and it seems that lzma_decoder can't handle that garbage data. Previously the script creating combined-image silently padded the kernel and rootfs, but since sysupgrade-tar doesn't, pad the default kernel image. Fixes: 900330f ("ath79: image: retire combined-image for Adtran/Bluesocket devices") Cc: Brian Gonyer <bgonyer@gmail.com> Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: sort device definitions in image/*Adrian Schmutzler2019-09-216-303/+301
| | | | | | | | | | | This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: Add support for Banana Pi M2 UltraHal Martin2019-09-213-2/+13
| | | | | | | | | | | | | | | | | | CPU: Allwinner R40 Quad-Core Cortex-A7 @ 1.2GHz GPU: Mali 400 MP2 Memory: 2GB DDR3 onboard (shared with GPU) Onboard: Storage microSD card slot Onboard: Storage 8GB eMMC Onboard: Network 10/100/1000M Ethernet RJ45 Onboard: Network WiFi 802.11b/g/n 1x1 (AMPAK AP6212; brcmfmac) Onboard header: SPI, I2C, GPIO, UART USB: Two USB 2.0 Host, One USB 2.0 OTG Known issues: - WiFi doesn't work - eMMC not supported Signed-off-by: Hal Martin <hal.martin@gmail.com>
* at91:sam9x: create sdcard imagesSandeep Sheriker M2019-09-211-2/+42
| | | | | | create sdcard images for sam9x25 & sam9x35 ek targets. Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* at91:sama5: create fit imageSandeep Sheriker M2019-09-212-1/+5
| | | | | | | create fit image & add it to sdcard image for sama5 target device. Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* kernel: bump 4.19 to 4.19.74Koen Vandeputte2019-09-208-12/+10
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-15504 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.145Koen Vandeputte2019-09-2010-22/+22
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.73Koen Vandeputte2019-09-208-147/+5
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 840-media-i2c-tda1997x-select-V4L2_FWNODE.patch - 079-v4.20-ARM-dts-qcom-ipq4019-fix-PCI-range.patch - 083-ARM-dts-qcom-ipq4019-enlarge-PCIe-BAR-range.patch - 084-ARM-dts-qcom-ipq4019-Fix-MSI-IRQ-type.patch Fixes: - CVE-2019-15030 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.144Koen Vandeputte2019-09-207-180/+97
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 816-pcie-support-layerscape.patch Fixes: -CVE-2019-15030 Compile-tested on: cns3xxx, layerscape Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add support for EnGenius ESR600Nick Briggs2019-09-204-1/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit Ethernet switch, a gigabit Ethernet WAN port and a USB port. Specification: - Bootloader: U-Boot - SoC: MediaTek MT7620A (600 MHz) - Flash: 16MB, Macronix MX25L12845E - RAM: 64MB, Nanya NT5TU32M16DG-AC - Serial: 115200 baud, no header, 3.3V J2: Vcc (arrow), Gnd, Tx, Rx - USB: USB 2, 5V - Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327 - WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N 300 Mb/s, 2T2R - WiFi1: 2.4 GHz 802.11 b/g/n integrated 300 Mb/s, 2T2R - Antennas: 2 per radio, internal - LEDs: 1 programmable power (amber) 2 programable radio (blue) 1 programable WPS-5G (blue) 1 non-programable WAN activity (blue) 1 unconfigured WPS-2.4G (amber) - Buttons: GPIO: Reset, WPS Installation: Use the OEM web interface to install the ...-factory.dlf image. Use the OpenWRT ...-sysupgrade.bin image for future upgrades. The J2 serial port can be accessed either by soldering in a header, standard 0.1" spacing, or by using pogo-pins against the back side. As configured by the OEM, the U-Boot boot delay is short, however quickly typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP" prompt. The TFTP client is configured by default with client: 192.168.99.9 server: 192.168.99.8 filename: uImageESR600 It will load an OpenWRT initramfs kernel with this method. Known issues: 1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational. LAN1 and LAN2 do not appear to power up. This issue is also present in the Lava LR25G001. 2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED, is not configured in the Device Tree specification. 3) The blue WAN activity LED is not configured in the Device Tree specification as this causes the AR8327 switch to fail to initialize. Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com> [merge conflict in 02_network] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7621: Add new device AsiaRF AP7621-NV1Daniel Danzberger2019-09-205-115/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Mediatek MT7621A CPU: 4x 880Mhz Cache: 32 KB I-Cache and 32 KB D-Cach 256 KB L2 Cache (shared by Dual-Core) RAM: DDR3 512MB 16bits BUS FLASH: 16MB Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN) POE: (1x PD, 2x PSE) USB: 1x 3.0 PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface) GPS: Quectel L70B SIM: 2 Slots BTN: Reset LED: - Power - Ethernet - Wifi - USB UART: UART is present as Pads with throughholes on the PCB. They are located on left side. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ The stock image is a modified openwrt and can be overflashed via sysupgrade -F Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> [merge conflict in mt7621.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Asus RT-AC85PBirger Koblitz2019-09-205-12/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Winbond W632GG6KB-1) FLASH: 128MB (Macronix MX30LF1G18AC-TI) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x USB 3.1 (Gen 1) BTN: Reset, WPS LED: - Power (blue) - 5Ghz (blue) - 2.4GHz (blue) - Internet (blue) - 4x LAN (blue) (LAN/WAN leds are not controllable by GPIOs) UART: UART is present as Pads marked J4 on the PCB. 3.3V - TX - RX - GND / 57600-8N1 3.3V is the square pad MAC: The MAC address on the router-label matches the MAC of the 2.4 GHz WiFi. LAN and WAN MAC are identical: MAC_LABEL+4 5 GHz WiFi MAC: also MAC_LABEL+4 Installation ------------ Via U-Boot tftpd: Switch on device, within 2s press reset button and keep pressed until power LED starts blinking slowly. Upload factory image via tftp put, the router's ip is 192.168.1.1 and expects the client on 192.168.1.75. The images also work on the Asus RT-AC65P models as tested by Gabor. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Tested-by: Gabor Varga <vargagab@gmail.com> [fixed Asus -> ASUS in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax RG21SBirger Koblitz2019-09-203-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Nanya NT5CC128M) FLASH: 16MB (Macronix MX25L12835F) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: No BTN: Reset, WPS LED: 4 red LEDs, indistinguishable when casing closed UART: UART is present as Pads marked J1 on the PCB. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the OEM web-interface (by default:http://192.168.1.1) The sysupgrade image can be installed via TFTP from the U-Boot bootloader. Connect ethernet port 2. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [flash node rename, EDIMAX -> Edimax, complete device model name] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* brcm2708: fix Hifiberry DAC+DSP package definitionÁlvaro Fernández Rojas2019-09-201-1/+1
| | | | | Fixes: ce536ae ("brcm2708: add support for Hifiberry DAC+DSP") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: Correctly search for the FIT image in mtd partition.Fredrik Olofsson2019-09-191-2/+2
| | | | | | Previously all iterations of the loop checked offset=0 in the partition. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
* lantiq-dsl: fix value of FECS counterMartin Schiller2019-09-191-13/+7
| | | | | | | Instead of the nFECS value, the nFEC value (the number of corrected code words) was mistakenly used. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ath79: add SUPPORTED_DEVICES to ubnt_nanostation-m-xwRoger Pueyo Centelles2019-09-191-1/+1
| | | | | | | | | | | | | | | | The ar71xx images for the Ubiquiti NanoStation M (XW) devices use "nanostation-m-xw" as the board name, but the ath79 images are only compatible with the "nano-m-xw" board name, so sysupgrade complains. By adding this additional supported device, sysuspgrade smoothly upgrades from ar71xx to ath79. Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb. Ref: https://github.com/openwrt/openwrt/pull/2418 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add XM device variant for Ubiquiti devicesAdrian Schmutzler2019-09-191-2/+2
| | | | | | | | | | So far, XW devices have DEVICE_VARIANT defined and XM devices have no DEVICE_VARIANT set. This adds DEVICE_VARIANT for XM devices, and moves definitions for both XM and XW to the common definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: provide label MAC addressAdrian Schmutzler2019-09-1932-10/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ramips. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - cudy,wr1000 - dlink,dir-615-d - dlink,dir-615-h1 - dlink,dir-860l-b1 - glinet,gl-mt300a - glinet,gl-mt300n - glinet,gl-mt750 - vocore,vocore2 - vocore,vocore2-lite - zbtlink,zbt-we1326 - zbtlink,zbt-wg3526 For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - dlink,dir-510l - dlink,dwr-116-a1 - dlink,dwr-118-a1 - dlink,dwr-118-a2 - dlink,dwr-921-c1 - dlink,dwr-922-e2 - all hiwifi devices - lava,lr-25g001 - xiaomi,mir3p Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: provide label MAC addressAdrian Schmutzler2019-09-192-0/+2
| | | | | | | This patch adds the label MAC address for several devices in ipq806x. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: provide label MAC addressAdrian Schmutzler2019-09-192-0/+2
| | | | | | | This patch adds the label MAC address for some devices in mpc85xx. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: provide label MAC addressAdrian Schmutzler2019-09-1954-12/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ath79. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - alfa-network,ap121f - avm,fritz300e - ubnt-xm devices For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - adtran,bsap1800-v2 - adtran,bsap1840 - dlink,dir-842-c1/-c2/-c3 - engenius,ecb1750 - iodata,etg3-r - iodata,wn-ac1167dgr - iodata,wn-ac1600dgr - iodata,wn-ac1600dgr2 - iodata,wn-ag300dgr - nec,wg800hp - nec,wg1200cr - trendnet,tew-823dru Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* brcm2708: add support for Hifiberry DAC+DSPÁlvaro Fernández Rojas2019-09-191-0/+20
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm2708: add support for Raspberry Pi 2B 1.2Álvaro Fernández Rojas2019-09-193-5/+18
| | | | | | RPi 2B 1.2 has a BCM2710/BCM2837 like RPi 3 devices. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm2708: update to latest patches from RPi foundationÁlvaro Fernández Rojas2019-09-19806-1570/+3639
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: 4.19: fix crash when setting up spi-gpioDENG Qingfang2019-09-191-0/+66
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If an spi-gpio was specified with num-chipselects = <0> in dts, kernel will crash: Unable to handle kernel paging request at virtual address 32697073 pgd = (ptrval) [32697073] *pgd=00000000 Internal error: Oops: 5 [# 1] SMP ARM Modules linked in: CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.19.72 #0 Hardware name: Generic DT based system PC is at validate_desc+0x28/0x80 LR is at gpiod_direction_output+0x14/0x128 ... [<c0544db4>] (validate_desc) from [<c0545228>] (gpiod_direction_output+0x14/0x128) [<c0545228>] (gpiod_direction_output) from [<c05fa714>] (spi_gpio_setup+0x58/0x64) [<c05fa714>] (spi_gpio_setup) from [<c05f7258>] (spi_setup+0x12c/0x148) [<c05f7258>] (spi_setup) from [<c05f7330>] (spi_add_device+0xbc/0x12c) [<c05f7330>] (spi_add_device) from [<c05f7f74>] (spi_register_controller+0x838/0x924) [<c05f7f74>] (spi_register_controller) from [<c05fa494>] (spi_bitbang_start+0x108/0x120) [<c05fa494>] (spi_bitbang_start) from [<c05faa34>] (spi_gpio_probe+0x314/0x338) [<c05faa34>] (spi_gpio_probe) from [<c05a844c>] (platform_drv_probe+0x34/0x70) The cause is spi_gpio_setup() did not check if the spi-gpio has chipselect pins before setting their direction and results in derefing an invalid pointer. The bug is spotted in kernel 4.19.72 and does not occur in 4.14. There is a similar fix upstream in kernel 5.2 in commit 249e2632dcd0 ("spi: gpio: Don't request CS GPIO in DT use-case"). Ref: https://patchwork.kernel.org/patch/11150619/ Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [use upstream patch, moved from hack to pending dir, commit facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link Archer C59v2Keith Maika2019-09-165-1/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath79 support for Archer C59v2, previously supported by ar71xx. TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 13:46:47 +0000